ICSA-26-209-04: Siemens SIMATIC S7-1500 CPU 1518(F)-4 PN/DP MFP

CISA's summary

Summary: Multiple vulnerabilities have been identified in the additional GNU/Linux subsystem of the firmware version V3.1.6 for the SIMATIC S7-1500 CPU 1518(F)-4 PN/DP MFP (incl. SIPLUS variant). Siemens is preparing fix versions and recommends specific countermeasures for products where fixes are not, or not yet available.

Products, as the advisory lists them

DeSpy has not checked any unit, hardware revision or firmware.

Vulnerabilities in this advisory

• CVE-2021-41617 — CVE-2021-41617 · CWE-311

  sshd in OpenSSH 6.2 through 8.x before 8.8, when certain non-default configurations are used, allows privilege escalation because supplemental groups are not initialized as expected. Helper programs for AuthorizedKeysCommand and AuthorizedPrincipalsCommand may run with privileges associated with group memberships of the sshd process, if the configuration specifies running the command as a different user.

• CVE-2023-28531 — CVE-2023-28531 · CWE-311

  ssh-add in OpenSSH before 9.3 adds smartcard keys to ssh-agent without the intended per-hop destination constraints. The earliest affected version is 8.9.

• CVE-2023-51384 — CVE-2023-51384 · CWE-304

  In ssh-agent in OpenSSH before 9.6, certain destination constraints can be incompletely applied. When destination constraints are specified during addition of PKCS#11-hosted private keys, these constraints are only applied to the first key, even if a PKCS#11 token returns multiple keys.

• CVE-2023-52927 — CVE-2023-52927 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: netfilter: allow exp not to be removed in nf_ct_find_expectation Currently nf_conntrack_in() calling nf_ct_find_expectation() will remove the exp from the hash table. However, in some scenario, we expect the exp not to be removed when the created ct will not be confirmed, like in OVS and TC conntrack in the following patches. This patch allows exp not to be removed by setting IPS_CONFIRMED in the status of the tmpl.

• CVE-2024-26783 — CVE-2024-26783 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: mm/vmscan: fix a bug calling wakeup_kswapd() with a wrong zone index With numa balancing on, when a numa system is running where a numa node doesn't have its local memory so it has no managed zones, the following oops has been observed. It's because wakeup_kswapd() is called with a wrong zone index, -1. Fixed it by checking the index before calling wakeup_kswapd(). > BUG: unable to handle page fault for address: 00000000000033f3 > #PF: supervisor read access in kernel mode > #PF: error_code(0x0000) - not-present page > PGD 0 P4D 0 > Oops: 0000 [#1] PREEMPT SMP NOPTI > CPU: 2 PID: 895 Comm: masim Not tainted 6.6.0-dirty #255 > Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS > rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 > RIP: 0010:wakeup_kswapd (./linux/mm/vmscan.c:7812) > Code: (omitted) > RSP: 0000:ffffc90004257d58 EFLAGS: 00010286 > RAX: ffffffffffffffff RBX: ffff88883fff0480 RCX: 0000000000000003 > RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88883fff0480 > RBP: ffffffffffffffff R08: ff0003ffffffffff R09: ffffffffffffffff > R10: ffff888106c95540 R11: 0000000055555554 R12: 0000000000000003 > R13: 0000000000000000 R14: 0000000000000000 R15: ffff88883fff0940 > FS: 00007fc4b8124740(0000) GS:ffff888827c00000(0000) knlGS:0000000000000000 > CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > CR2: 00000000000033f3 CR3: 000000026cc08004 CR4: 0000000000770ee0 > DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 > DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 > PKRU: 55555554 > Call Trace: > <TASK> > ? __die > ? page_fault_oops > ? __pte_offset_map_lock > ? exc_page_fault > ? asm_exc_page_fault > ? wakeup_kswapd > migrate_misplaced_page > __handle_mm_fault > handle_mm_fault > do_user_addr_fault > exc_page_fault > asm_exc_page_fault > RIP: 0033:0x55b897ba0808 > Code: (omitted) > RSP: 002b:00007ffeefa821a0 EFLAGS: 00010287 > RAX: 000055b89983acd0 RBX: 00007ffeefa823f8 RCX: 000055b89983acd0 > RDX: 00007fc2f8122010 RSI: 0000000000020000 RDI: 000055b89983acd0 > RBP: 00007ffeefa821a0 R08: 0000000000000037 R09: 0000000000000075 > R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000 > R13: 00007ffeefa82410 R14: 000055b897ba5dd8 R15: 00007fc4b8340000 > </TASK>

• CVE-2024-27056 — CVE-2024-27056 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: ensure offloading TID queue exists The resume code path assumes that the TX queue for the offloading TID has been configured. At resume time it then tries to sync the write pointer as it may have been updated by the firmware. In the unusual event that no packets have been send on TID 0, the queue will not have been allocated and this causes a crash. Fix this by ensuring the queue exist at suspend time.

• CVE-2024-28956 — CVE-2024-28956 · CWE-1421

  Exposure of Sensitive Information in Shared Microarchitectural Structures during Transient Execution for some Intel(R) Processors may allow an authenticated user to potentially enable information disclosure via local access.

• CVE-2024-36903 — CVE-2024-36903 · CWE-362

  In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix potential uninit-value access in __ip6_make_skb() As it was done in commit fc1092f51567 ("ipv4: Fix uninit-value access in __ip_make_skb()") for IPv4, check FLOWI_FLAG_KNOWN_NH on fl6->flowi6_flags instead of testing HDRINCL on the socket to avoid a race condition which causes uninit-value access.

• CVE-2024-36927 — CVE-2024-36927 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix uninit-value access in __ip_make_skb() KMSAN reported uninit-value access in __ip_make_skb() [1]. __ip_make_skb() tests HDRINCL to know if the skb has icmphdr. However, HDRINCL can cause a race condition. If calling setsockopt(2) with IP_HDRINCL changes HDRINCL while __ip_make_skb() is running, the function will access icmphdr in the skb even if it is not included. This causes the issue reported by KMSAN. Check FLOWI_FLAG_KNOWN_NH on fl4->flowi4_flags instead of testing HDRINCL on the socket. Also, fl4->fl4_icmp_type and fl4->fl4_icmp_code are not initialized. These are union in struct flowi4 and are implicitly initialized by flowi4_init_output(), but we should not rely on specific union layout. Initialize these explicitly in raw_sendmsg(). [1] BUG: KMSAN: uninit-value in __ip_make_skb+0x2b74/0x2d20 net/ipv4/ip_output.c:1481 __ip_make_skb+0x2b74/0x2d20 net/ipv4/ip_output.c:1481 ip_finish_skb include/net/ip.h:243 [inline] ip_push_pending_frames+0x4c/0x5c0 net/ipv4/ip_output.c:1508 raw_sendmsg+0x2381/0x2690 net/ipv4/raw.c:654 inet_sendmsg+0x27b/0x2a0 net/ipv4/af_inet.c:851 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x274/0x3c0 net/socket.c:745 __sys_sendto+0x62c/0x7b0 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x130/0x200 net/socket.c:2199 do_syscall_64+0xd8/0x1f0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x6d/0x75 Uninit was created at: slab_post_alloc_hook mm/slub.c:3804 [inline] slab_alloc_node mm/slub.c:3845 [inline] kmem_cache_alloc_node+0x5f6/0xc50 mm/slub.c:3888 kmalloc_reserve+0x13c/0x4a0 net/core/skbuff.c:577 __alloc_skb+0x35a/0x7c0 net/core/skbuff.c:668 alloc_skb include/linux/skbuff.h:1318 [inline] __ip_append_data+0x49ab/0x68c0 net/ipv4/ip_output.c:1128 ip_append_data+0x1e7/0x260 net/ipv4/ip_output.c:1365 raw_sendmsg+0x22b1/0x2690 net/ipv4/raw.c:648 inet_sendmsg+0x27b/0x2a0 net/ipv4/af_inet.c:851 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x274/0x3c0 net/socket.c:745 __sys_sendto+0x62c/0x7b0 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x130/0x200 net/socket.c:2199 do_syscall_64+0xd8/0x1f0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x6d/0x75 CPU: 1 PID: 15709 Comm: syz-executor.7 Not tainted 6.8.0-11567-gb3603fcb79b1 #25 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-1.fc39 04/01/2014

• CVE-2024-42079 — CVE-2024-42079 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: gfs2: Fix NULL pointer dereference in gfs2_log_flush In gfs2_jindex_free(), set sdp->sd_jdesc to NULL under the log flush lock to provide exclusion against gfs2_log_flush(). In gfs2_log_flush(), check if sdp->sd_jdesc is non-NULL before dereferencing it. Otherwise, we could run into a NULL pointer dereference when outstanding glock work races with an unmount (glock_work_func -> run_queue -> do_xmote -> inode_go_sync -> gfs2_log_flush).

• CVE-2024-46786 — CVE-2024-46786 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: fscache: delete fscache_cookie_lru_timer when fscache exits to avoid UAF The fscache_cookie_lru_timer is initialized when the fscache module is inserted, but is not deleted when the fscache module is removed. If timer_reduce() is called before removing the fscache module, the fscache_cookie_lru_timer will be added to the timer list of the current cpu. Afterwards, a use-after-free will be triggered in the softIRQ after removing the fscache module, as follows: ================================================================== BUG: unable to handle page fault for address: fffffbfff803c9e9 PF: supervisor read access in kernel mode PF: error_code(0x0000) - not-present page PGD 21ffea067 P4D 21ffea067 PUD 21ffe6067 PMD 110a7c067 PTE 0 Oops: Oops: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Tainted: G W 6.11.0-rc3 #855 Tainted: [W]=WARN RIP: 0010:__run_timer_base.part.0+0x254/0x8a0 Call Trace: <IRQ> tmigr_handle_remote_up+0x627/0x810 __walk_groups.isra.0+0x47/0x140 tmigr_handle_remote+0x1fa/0x2f0 handle_softirqs+0x180/0x590 irq_exit_rcu+0x84/0xb0 sysvec_apic_timer_interrupt+0x6e/0x90 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x1a/0x20 RIP: 0010:default_idle+0xf/0x20 default_idle_call+0x38/0x60 do_idle+0x2b5/0x300 cpu_startup_entry+0x54/0x60 start_secondary+0x20d/0x280 common_startup_64+0x13e/0x148 </TASK> Modules linked in: [last unloaded: netfs] ================================================================== Therefore delete fscache_cookie_lru_timer when removing the fscahe module.

• CVE-2024-47736 — CVE-2024-47736 · CWE-404

  In the Linux kernel, the following vulnerability has been resolved: erofs: handle overlapped pclusters out of crafted images properly syzbot reported a task hang issue due to a deadlock case where it is waiting for the folio lock of a cached folio that will be used for cache I/Os. After looking into the crafted fuzzed image, I found it's formed with several overlapped big pclusters as below: Ext: logical offset | length : physical offset | length 0: 0.. 16384 | 16384 : 151552.. 167936 | 16384 1: 16384.. 32768 | 16384 : 155648.. 172032 | 16384 2: 32768.. 49152 | 16384 : 537223168.. 537239552 | 16384 ... Here, extent 0/1 are physically overlapped although it's entirely _impossible_ for normal filesystem images generated by mkfs. First, managed folios containing compressed data will be marked as up-to-date and then unlocked immediately (unlike in-place folios) when compressed I/Os are complete. If physical blocks are not submitted in the incremental order, there should be separate BIOs to avoid dependency issues. However, the current code mis-arranges z_erofs_fill_bio_vec() and BIO submission which causes unexpected BIO waits. Second, managed folios will be connected to their own pclusters for efficient inter-queries. However, this is somewhat hard to implement easily if overlapped big pclusters exist. Again, these only appear in fuzzed images so let's simply fall back to temporary short-lived pages for correctness. Additionally, it justifies that referenced managed folios cannot be truncated for now and reverts part of commit 2080ca1ed3e4 ("erofs: tidy up `struct z_erofs_bvec`") for simplicity although it shouldn't be any difference.

• CVE-2024-47809 — CVE-2024-47809 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: dlm: fix possible lkb_resource null dereference This patch fixes a possible null pointer dereference when this function is called from request_lock() as lkb->lkb_resource is not assigned yet, only after validate_lock_args() by calling attach_lkb(). Another issue is that a resource name could be a non printable bytearray and we cannot assume to be ASCII coded. The log functionality is probably never being hit when DLM is used in normal way and no debug logging is enabled. The null pointer dereference can only occur on a new created lkb that does not have the resource assigned yet, it probably never hits the null pointer dereference but we should be sure that other changes might not change this behaviour and we actually can hit the mentioned null pointer dereference. In this patch we just drop the printout of the resource name, the lkb id is enough to make a possible connection to a resource name if this exists.

• CVE-2024-49968 — CVE-2024-49968 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: ext4: filesystems without casefold feature cannot be mounted with siphash When mounting the ext4 filesystem, if the default hash version is set to DX_HASH_SIPHASH but the casefold feature is not set, exit the mounting.

• CVE-2024-49994 — CVE-2024-49994 · CWE-190

  In the Linux kernel, the following vulnerability has been resolved: block: fix integer overflow in BLKSECDISCARD I independently rediscovered commit 22d24a544b0d49bbcbd61c8c0eaf77d3c9297155 block: fix overflow in blk_ioctl_discard() but for secure erase. Same problem: uint64_t r[2] = {512, 18446744073709551104ULL}; ioctl(fd, BLKSECDISCARD, r); will enter near infinite loop inside blkdev_issue_secure_erase(): a.out: attempt to access beyond end of device loop0: rw=5, sector=3399043073, nr_sectors = 1024 limit=2048 bio_check_eod: 3286214 callbacks suppressed

• CVE-2024-49998 — CVE-2024-49998 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: net: dsa: improve shutdown sequence Alexander Sverdlin presents 2 problems during shutdown with the lan9303 driver. One is specific to lan9303 and the other just happens to reproduce there. The first problem is that lan9303 is unique among DSA drivers in that it calls dev_get_drvdata() at "arbitrary runtime" (not probe, not shutdown, not remove): phy_state_machine() -> ... -> dsa_user_phy_read() -> ds->ops->phy_read() -> lan9303_phy_read() -> chip->ops->phy_read() -> lan9303_mdio_phy_read() -> dev_get_drvdata() But we never stop the phy_state_machine(), so it may continue to run after dsa_switch_shutdown(). Our common pattern in all DSA drivers is to set drvdata to NULL to suppress the remove() method that may come afterwards. But in this case it will result in an NPD. The second problem is that the way in which we set dp->conduit->dsa_ptr = NULL; is concurrent with receive packet processing. dsa_switch_rcv() checks once whether dev->dsa_ptr is NULL, but afterwards, rather than continuing to use that non-NULL value, dev->dsa_ptr is dereferenced again and again without NULL checks: dsa_conduit_find_user() and many other places. In between dereferences, there is no locking to ensure that what was valid once continues to be valid. Both problems have the common aspect that closing the conduit interface solves them. In the first case, dev_close(conduit) triggers the NETDEV_GOING_DOWN event in dsa_user_netdevice_event() which closes user ports as well. dsa_port_disable_rt() calls phylink_stop(), which synchronously stops the phylink state machine, and ds->ops->phy_read() will thus no longer call into the driver after this point. In the second case, dev_close(conduit) should do this, as per Documentation/networking/driver.rst: | Quiescence | ---------- | | After the ndo_stop routine has been called, the hardware must | not receive or transmit any data. All in flight packets must | be aborted. If necessary, poll or wait for completion of | any reset commands. So it should be sufficient to ensure that later, when we zeroize conduit->dsa_ptr, there will be no concurrent dsa_switch_rcv() call on this conduit. The addition of the netif_device_detach() function is to ensure that ioctls, rtnetlinks and ethtool requests on the user ports no longer propagate down to the driver - we're no longer prepared to handle them. The race condition actually did not exist when commit 0650bf52b31f ("net: dsa: be compatible with masters which unregister on shutdown") first introduced dsa_switch_shutdown(). It was created later, when we stopped unregistering the user interfaces from a bad spot, and we just replaced that sequence with a racy zeroization of conduit->dsa_ptr (one which doesn't ensure that the interfaces aren't up).

• CVE-2024-50014 — CVE-2024-50014 · CWE-457

  In the Linux kernel, the following vulnerability has been resolved: ext4: fix access to uninitialised lock in fc replay path The following kernel trace can be triggered with fstest generic/629 when executed against a filesystem with fast-commit feature enabled: INFO: trying to register non-static key. The code is fine but needs lockdep annotation, or maybe you didn't initialize this object before use? turning off the locking correctness validator. CPU: 0 PID: 866 Comm: mount Not tainted 6.10.0+ #11 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-3-gd478f380-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x66/0x90 register_lock_class+0x759/0x7d0 __lock_acquire+0x85/0x2630 ? __find_get_block+0xb4/0x380 lock_acquire+0xd1/0x2d0 ? __ext4_journal_get_write_access+0xd5/0x160 _raw_spin_lock+0x33/0x40 ? __ext4_journal_get_write_access+0xd5/0x160 __ext4_journal_get_write_access+0xd5/0x160 ext4_reserve_inode_write+0x61/0xb0 __ext4_mark_inode_dirty+0x79/0x270 ? ext4_ext_replay_set_iblocks+0x2f8/0x450 ext4_ext_replay_set_iblocks+0x330/0x450 ext4_fc_replay+0x14c8/0x1540 ? jread+0x88/0x2e0 ? rcu_is_watching+0x11/0x40 do_one_pass+0x447/0xd00 jbd2_journal_recover+0x139/0x1b0 jbd2_journal_load+0x96/0x390 ext4_load_and_init_journal+0x253/0xd40 ext4_fill_super+0x2cc6/0x3180 ... In the replay path there's an attempt to lock sbi->s_bdev_wb_lock in function ext4_check_bdev_write_error(). Unfortunately, at this point this spinlock has not been initialized yet. Moving it's initialization to an earlier point in __ext4_fill_super() fixes this splat.

• CVE-2024-50063 — CVE-2024-50063 · CWE-841

  In the Linux kernel, the following vulnerability has been resolved: bpf: Prevent tail call between progs attached to different hooks bpf progs can be attached to kernel functions, and the attached functions can take different parameters or return different return values. If prog attached to one kernel function tail calls prog attached to another kernel function, the ctx access or return value verification could be bypassed. For example, if prog1 is attached to func1 which takes only 1 parameter and prog2 is attached to func2 which takes two parameters. Since verifier assumes the bpf ctx passed to prog2 is constructed based on func2's prototype, verifier allows prog2 to access the second parameter from the bpf ctx passed to it. The problem is that verifier does not prevent prog1 from passing its bpf ctx to prog2 via tail call. In this case, the bpf ctx passed to prog2 is constructed from func1 instead of func2, that is, the assumption for ctx access verification is bypassed. Another example, if BPF LSM prog1 is attached to hook file_alloc_security, and BPF LSM prog2 is attached to hook bpf_lsm_audit_rule_known. Verifier knows the return value rules for these two hooks, e.g. it is legal for bpf_lsm_audit_rule_known to return positive number 1, and it is illegal for file_alloc_security to return positive number. So verifier allows prog2 to return positive number 1, but does not allow prog1 to return positive number. The problem is that verifier does not prevent prog1 from calling prog2 via tail call. In this case, prog2's return value 1 will be used as the return value for prog1's hook file_alloc_security. That is, the return value rule is bypassed. This patch adds restriction for tail call to prevent such bypasses.

• CVE-2024-50164 — CVE-2024-50164 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bpf: Fix overloading of MEM_UNINIT's meaning Lonial reported an issue in the BPF verifier where check_mem_size_reg() has the following code: if (!tnum_is_const(reg->var_off)) /* For unprivileged variable accesses, disable raw * mode so that the program is required to * initialize all the memory that the helper could * just partially fill up. */ meta = NULL; This means that writes are not checked when the register containing the size of the passed buffer has not a fixed size. Through this bug, a BPF program can write to a map which is marked as read-only, for example, .rodata global maps. The problem is that MEM_UNINIT's initial meaning that "the passed buffer to the BPF helper does not need to be initialized" which was added back in commit 435faee1aae9 ("bpf, verifier: add ARG_PTR_TO_RAW_STACK type") got overloaded over time with "the passed buffer is being written to". The problem however is that checks such as the above which were added later via 06c1c049721a ("bpf: allow helpers access to variable memory") set meta to NULL in order force the user to always initialize the passed buffer to the helper. Due to the current double meaning of MEM_UNINIT, this bypasses verifier write checks to the memory (not boundary checks though) and only assumes the latter memory is read instead. Fix this by reverting MEM_UNINIT back to its original meaning, and having MEM_WRITE as an annotation to BPF helpers in order to then trigger the BPF verifier checks for writing to memory. Some notes: check_arg_pair_ok() ensures that for ARG_CONST_SIZE{,_OR_ZERO} we can access fn->arg_type[arg - 1] since it must contain a preceding ARG_PTR_TO_MEM. For check_mem_reg() the meta argument can be removed altogether since we do check both BPF_READ and BPF_WRITE. Same for the equivalent check_kfunc_mem_size_reg().

• CVE-2024-50298 — CVE-2024-50298 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: net: enetc: allocate vf_state during PF probes In the previous implementation, vf_state is allocated memory only when VF is enabled. However, net_device_ops::ndo_set_vf_mac() may be called before VF is enabled to configure the MAC address of VF. If this is the case, enetc_pf_set_vf_mac() will access vf_state, resulting in access to a null pointer. The simplified error log is as follows. root@ls1028ardb:~# ip link set eno0 vf 1 mac 00:0c:e7:66:77:89 [ 173.543315] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004 [ 173.637254] pc : enetc_pf_set_vf_mac+0x3c/0x80 Message from sy [ 173.641973] lr : do_setlink+0x4a8/0xec8 [ 173.732292] Call trace: [ 173.734740] enetc_pf_set_vf_mac+0x3c/0x80 [ 173.738847] __rtnl_newlink+0x530/0x89c [ 173.742692] rtnl_newlink+0x50/0x7c [ 173.746189] rtnetlink_rcv_msg+0x128/0x390 [ 173.750298] netlink_rcv_skb+0x60/0x130 [ 173.754145] rtnetlink_rcv+0x18/0x24 [ 173.757731] netlink_unicast+0x318/0x380 [ 173.761665] netlink_sendmsg+0x17c/0x3c8

• CVE-2024-53124 — CVE-2024-53124 · CWE-362

  In the Linux kernel, the following vulnerability has been resolved: net: fix data-races around sk->sk_forward_alloc Syzkaller reported this warning: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 16 at net/ipv4/af_inet.c:156 inet_sock_destruct+0x1c5/0x1e0 Modules linked in: CPU: 0 UID: 0 PID: 16 Comm: ksoftirqd/0 Not tainted 6.12.0-rc5 #26 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:inet_sock_destruct+0x1c5/0x1e0 Code: 24 12 4c 89 e2 5b 48 c7 c7 98 ec bb 82 41 5c e9 d1 18 17 ff 4c 89 e6 5b 48 c7 c7 d0 ec bb 82 41 5c e9 bf 18 17 ff 0f 0b eb 83 <0f> 0b eb 97 0f 0b eb 87 0f 0b e9 68 ff ff ff 66 66 2e 0f 1f 84 00 RSP: 0018:ffffc9000008bd90 EFLAGS: 00010206 RAX: 0000000000000300 RBX: ffff88810b172a90 RCX: 0000000000000007 RDX: 0000000000000002 RSI: 0000000000000300 RDI: ffff88810b172a00 RBP: ffff88810b172a00 R08: ffff888104273c00 R09: 0000000000100007 R10: 0000000000020000 R11: 0000000000000006 R12: ffff88810b172a00 R13: 0000000000000004 R14: 0000000000000000 R15: ffff888237c31f78 FS: 0000000000000000(0000) GS:ffff888237c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffc63fecac8 CR3: 000000000342e000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __warn+0x88/0x130 ? inet_sock_destruct+0x1c5/0x1e0 ? report_bug+0x18e/0x1a0 ? handle_bug+0x53/0x90 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? inet_sock_destruct+0x1c5/0x1e0 __sk_destruct+0x2a/0x200 rcu_do_batch+0x1aa/0x530 ? rcu_do_batch+0x13b/0x530 rcu_core+0x159/0x2f0 handle_softirqs+0xd3/0x2b0 ? __pfx_smpboot_thread_fn+0x10/0x10 run_ksoftirqd+0x25/0x30 smpboot_thread_fn+0xdd/0x1d0 kthread+0xd3/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x34/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ---[ end trace 0000000000000000 ]--- Its possible that two threads call tcp_v6_do_rcv()/sk_forward_alloc_add() concurrently when sk->sk_state == TCP_LISTEN with sk->sk_lock unlocked, which triggers a data-race around sk->sk_forward_alloc: tcp_v6_rcv tcp_v6_do_rcv skb_clone_and_charge_r sk_rmem_schedule __sk_mem_schedule sk_forward_alloc_add() skb_set_owner_r sk_mem_charge sk_forward_alloc_add() __kfree_skb skb_release_all skb_release_head_state sock_rfree sk_mem_uncharge sk_forward_alloc_add() sk_mem_reclaim // set local var reclaimable __sk_mem_reclaim sk_forward_alloc_add() In this syzkaller testcase, two threads call tcp_v6_do_rcv() with skb->truesize=768, the sk_forward_alloc changes like this: (cpu 1) | (cpu 2) | sk_forward_alloc ... | ... | 0 __sk_mem_schedule() | | +4096 = 4096 | __sk_mem_schedule() | +4096 = 8192 sk_mem_charge() | | -768 = 7424 | sk_mem_charge() | -768 = 6656 ... | ... | sk_mem_uncharge() | | +768 = 7424 reclaimable=7424 | | | sk_mem_uncharge() | +768 = 8192 | reclaimable=8192 | __sk_mem_reclaim() | | -4096 = 4096 | __sk_mem_reclaim() | -8192 = -4096 != 0 The skb_clone_and_charge_r() should not be called in tcp_v6_do_rcv() when sk->sk_state is TCP_LISTEN, it happens later in tcp_v6_syn_recv_sock(). Fix the same issue in dccp_v6_do_rcv().

• CVE-2024-53170 — CVE-2024-53170 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: block: fix uaf for flush rq while iterating tags blk_mq_clear_flush_rq_mapping() is not called during scsi probe, by checking blk_queue_init_done(). However, QUEUE_FLAG_INIT_DONE is cleared in del_gendisk by commit aec89dc5d421 ("block: keep q_usage_counter in atomic mode after del_gendisk"), hence for disk like scsi, following blk_mq_destroy_queue() will not clear flush rq from tags->rqs[] as well, cause following uaf that is found by our syzkaller for v6.6: ================================================================== BUG: KASAN: slab-use-after-free in blk_mq_find_and_get_req+0x16e/0x1a0 block/blk-mq-tag.c:261 Read of size 4 at addr ffff88811c969c20 by task kworker/1:2H/224909 CPU: 1 PID: 224909 Comm: kworker/1:2H Not tainted 6.6.0-ga836a5060850 #32 Workqueue: kblockd blk_mq_timeout_work Call Trace: __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x91/0xf0 lib/dump_stack.c:106 print_address_description.constprop.0+0x66/0x300 mm/kasan/report.c:364 print_report+0x3e/0x70 mm/kasan/report.c:475 kasan_report+0xb8/0xf0 mm/kasan/report.c:588 blk_mq_find_and_get_req+0x16e/0x1a0 block/blk-mq-tag.c:261 bt_iter block/blk-mq-tag.c:288 [inline] __sbitmap_for_each_set include/linux/sbitmap.h:295 [inline] sbitmap_for_each_set include/linux/sbitmap.h:316 [inline] bt_for_each+0x455/0x790 block/blk-mq-tag.c:325 blk_mq_queue_tag_busy_iter+0x320/0x740 block/blk-mq-tag.c:534 blk_mq_timeout_work+0x1a3/0x7b0 block/blk-mq.c:1673 process_one_work+0x7c4/0x1450 kernel/workqueue.c:2631 process_scheduled_works kernel/workqueue.c:2704 [inline] worker_thread+0x804/0xe40 kernel/workqueue.c:2785 kthread+0x346/0x450 kernel/kthread.c:388 ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1b/0x30 arch/x86/entry/entry_64.S:293 Allocated by task 942: kasan_save_stack+0x22/0x50 mm/kasan/common.c:45 kasan_set_track+0x25/0x30 mm/kasan/common.c:52 ____kasan_kmalloc mm/kasan/common.c:374 [inline] __kasan_kmalloc mm/kasan/common.c:383 [inline] __kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:380 kasan_kmalloc include/linux/kasan.h:198 [inline] __do_kmalloc_node mm/slab_common.c:1007 [inline] __kmalloc_node+0x69/0x170 mm/slab_common.c:1014 kmalloc_node include/linux/slab.h:620 [inline] kzalloc_node include/linux/slab.h:732 [inline] blk_alloc_flush_queue+0x144/0x2f0 block/blk-flush.c:499 blk_mq_alloc_hctx+0x601/0x940 block/blk-mq.c:3788 blk_mq_alloc_and_init_hctx+0x27f/0x330 block/blk-mq.c:4261 blk_mq_realloc_hw_ctxs+0x488/0x5e0 block/blk-mq.c:4294 blk_mq_init_allocated_queue+0x188/0x860 block/blk-mq.c:4350 blk_mq_init_queue_data block/blk-mq.c:4166 [inline] blk_mq_init_queue+0x8d/0x100 block/blk-mq.c:4176 scsi_alloc_sdev+0x843/0xd50 drivers/scsi/scsi_scan.c:335 scsi_probe_and_add_lun+0x77c/0xde0 drivers/scsi/scsi_scan.c:1189 __scsi_scan_target+0x1fc/0x5a0 drivers/scsi/scsi_scan.c:1727 scsi_scan_channel drivers/scsi/scsi_scan.c:1815 [inline] scsi_scan_channel+0x14b/0x1e0 drivers/scsi/scsi_scan.c:1791 scsi_scan_host_selected+0x2fe/0x400 drivers/scsi/scsi_scan.c:1844 scsi_scan+0x3a0/0x3f0 drivers/scsi/scsi_sysfs.c:151 store_scan+0x2a/0x60 drivers/scsi/scsi_sysfs.c:191 dev_attr_store+0x5c/0x90 drivers/base/core.c:2388 sysfs_kf_write+0x11c/0x170 fs/sysfs/file.c:136 kernfs_fop_write_iter+0x3fc/0x610 fs/kernfs/file.c:338 call_write_iter include/linux/fs.h:2083 [inline] new_sync_write+0x1b4/0x2d0 fs/read_write.c:493 vfs_write+0x76c/0xb00 fs/read_write.c:586 ksys_write+0x127/0x250 fs/read_write.c:639 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x70/0x120 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x78/0xe2 Freed by task 244687: kasan_save_stack+0x22/0x50 mm/kasan/common.c:45 kasan_set_track+0x25/0x30 mm/kasan/common.c:52 kasan_save_free_info+0x2b/0x50 mm/kasan/generic.c:522 ____kasan_slab_free mm/kasan/common.c:236 [inline] __kasan_slab_free+0x12a/0x1b0 mm/kasan/common.c:244 kasan_slab_free include/linux/kasan.h:164 [in ---truncated---

• CVE-2024-54458 — CVE-2024-54458 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: bsg: Set bsg_queue to NULL after removal Currently, this does not cause any issues, but I believe it is necessary to set bsg_queue to NULL after removing it to prevent potential use-after-free (UAF) access.

• CVE-2024-56631 — CVE-2024-56631 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: scsi: sg: Fix slab-use-after-free read in sg_release() Fix a use-after-free bug in sg_release(), detected by syzbot with KASAN: BUG: KASAN: slab-use-after-free in lock_release+0x151/0xa30 kernel/locking/lockdep.c:5838 __mutex_unlock_slowpath+0xe2/0x750 kernel/locking/mutex.c:912 sg_release+0x1f4/0x2e0 drivers/scsi/sg.c:407 In sg_release(), the function kref_put(&sfp->f_ref, sg_remove_sfp) is called before releasing the open_rel_lock mutex. The kref_put() call may decrement the reference count of sfp to zero, triggering its cleanup through sg_remove_sfp(). This cleanup includes scheduling deferred work via sg_remove_sfp_usercontext(), which ultimately frees sfp. After kref_put(), sg_release() continues to unlock open_rel_lock and may reference sfp or sdp. If sfp has already been freed, this results in a slab-use-after-free error. Move the kref_put(&sfp->f_ref, sg_remove_sfp) call after unlocking the open_rel_lock mutex. This ensures: - No references to sfp or sdp occur after the reference count is decremented. - Cleanup functions such as sg_remove_sfp() and sg_remove_sfp_usercontext() can safely execute without impacting the mutex handling in sg_release(). The fix has been tested and validated by syzbot. This patch closes the bug reported at the following syzkaller link and ensures proper sequencing of resource cleanup and mutex operations, eliminating the risk of use-after-free errors in sg_release().

• CVE-2024-56703 — CVE-2024-56703 · CWE-835

  In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix soft lockups in fib6_select_path under high next hop churn Soft lockups have been observed on a cluster of Linux-based edge routers located in a highly dynamic environment. Using the `bird` service, these routers continuously update BGP-advertised routes due to frequently changing nexthop destinations, while also managing significant IPv6 traffic. The lockups occur during the traversal of the multipath circular linked-list in the `fib6_select_path` function, particularly while iterating through the siblings in the list. The issue typically arises when the nodes of the linked list are unexpectedly deleted concurrently on a different core—indicated by their 'next' and 'previous' elements pointing back to the node itself and their reference count dropping to zero. This results in an infinite loop, leading to a soft lockup that triggers a system panic via the watchdog timer. Apply RCU primitives in the problematic code sections to resolve the issue. Where necessary, update the references to fib6_siblings to annotate or use the RCU APIs. Include a test script that reproduces the issue. The script periodically updates the routing table while generating a heavy load of outgoing IPv6 traffic through multiple iperf3 clients. It consistently induces infinite soft lockups within a couple of minutes. Kernel log: 0 [ffffbd13003e8d30] machine_kexec at ffffffff8ceaf3eb 1 [ffffbd13003e8d90] __crash_kexec at ffffffff8d0120e3 2 [ffffbd13003e8e58] panic at ffffffff8cef65d4 3 [ffffbd13003e8ed8] watchdog_timer_fn at ffffffff8d05cb03 4 [ffffbd13003e8f08] __hrtimer_run_queues at ffffffff8cfec62f 5 [ffffbd13003e8f70] hrtimer_interrupt at ffffffff8cfed756 6 [ffffbd13003e8fd0] __sysvec_apic_timer_interrupt at ffffffff8cea01af 7 [ffffbd13003e8ff0] sysvec_apic_timer_interrupt at ffffffff8df1b83d -- <IRQ stack> -- 8 [ffffbd13003d3708] asm_sysvec_apic_timer_interrupt at ffffffff8e000ecb [exception RIP: fib6_select_path+299] RIP: ffffffff8ddafe7b RSP: ffffbd13003d37b8 RFLAGS: 00000287 RAX: ffff975850b43600 RBX: ffff975850b40200 RCX: 0000000000000000 RDX: 000000003fffffff RSI: 0000000051d383e4 RDI: ffff975850b43618 RBP: ffffbd13003d3800 R8: 0000000000000000 R9: ffff975850b40200 R10: 0000000000000000 R11: 0000000000000000 R12: ffffbd13003d3830 R13: ffff975850b436a8 R14: ffff975850b43600 R15: 0000000000000007 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 9 [ffffbd13003d3808] ip6_pol_route at ffffffff8ddb030c 10 [ffffbd13003d3888] ip6_pol_route_input at ffffffff8ddb068c 11 [ffffbd13003d3898] fib6_rule_lookup at ffffffff8ddf02b5 12 [ffffbd13003d3928] ip6_route_input at ffffffff8ddb0f47 13 [ffffbd13003d3a18] ip6_rcv_finish_core.constprop.0 at ffffffff8dd950d0 14 [ffffbd13003d3a30] ip6_list_rcv_finish.constprop.0 at ffffffff8dd96274 15 [ffffbd13003d3a98] ip6_sublist_rcv at ffffffff8dd96474 16 [ffffbd13003d3af8] ipv6_list_rcv at ffffffff8dd96615 17 [ffffbd13003d3b60] __netif_receive_skb_list_core at ffffffff8dc16fec 18 [ffffbd13003d3be0] netif_receive_skb_list_internal at ffffffff8dc176b3 19 [ffffbd13003d3c50] napi_gro_receive at ffffffff8dc565b9 20 [ffffbd13003d3c80] ice_receive_skb at ffffffffc087e4f5 [ice] 21 [ffffbd13003d3c90] ice_clean_rx_irq at ffffffffc0881b80 [ice] 22 [ffffbd13003d3d20] ice_napi_poll at ffffffffc088232f [ice] 23 [ffffbd13003d3d80] __napi_poll at ffffffff8dc18000 24 [ffffbd13003d3db8] net_rx_action at ffffffff8dc18581 25 [ffffbd13003d3e40] __do_softirq at ffffffff8df352e9 26 [ffffbd13003d3eb0] run_ksoftirqd at ffffffff8ceffe47 27 [ffffbd13003d3ec0] smpboot_thread_fn at ffffffff8cf36a30 28 [ffffbd13003d3ee8] kthread at ffffffff8cf2b39f 29 [ffffbd13003d3f28] ret_from_fork at ffffffff8ce5fa64 30 [ffffbd13003d3f50] ret_from_fork_asm at ffffffff8ce03cbb

• CVE-2024-56719 — CVE-2024-56719 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: stmmac: fix TSO DMA API usage causing oops Commit 66600fac7a98 ("net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data") moved the assignment of tx_skbuff_dma[]'s members to be later in stmmac_tso_xmit(). The buf (dma cookie) and len stored in this structure are passed to dma_unmap_single() by stmmac_tx_clean(). The DMA API requires that the dma cookie passed to dma_unmap_single() is the same as the value returned from dma_map_single(). However, by moving the assignment later, this is not the case when priv->dma_cap.addr64 > 32 as "des" is offset by proto_hdr_len. This causes problems such as: dwc-eth-dwmac 2490000.ethernet eth0: Tx DMA map failed and with DMA_API_DEBUG enabled: DMA-API: dwc-eth-dwmac 2490000.ethernet: device driver tries to +free DMA memory it has not allocated [device address=0x000000ffffcf65c0] [size=66 bytes] Fix this by maintaining "des" as the original DMA cookie, and use tso_des to pass the offset DMA cookie to stmmac_tso_allocator(). Full details of the crashes can be found at: https://lore.kernel.org/all/d8112193-0386-4e14-b516-37c2d838171a@nvidia.com/ https://lore.kernel.org/all/klkzp5yn5kq5efgtrow6wbvnc46bcqfxs65nz3qy77ujr5turc@bwwhelz2l4dw/

• CVE-2024-57917 — CVE-2024-57917 · CWE-362

  In the Linux kernel, the following vulnerability has been resolved: topology: Keep the cpumask unchanged when printing cpumap During fuzz testing, the following warning was discovered: different return values (15 and 11) from vsnprintf("%*pbl ", ...) test:keyward is WARNING in kvasprintf WARNING: CPU: 55 PID: 1168477 at lib/kasprintf.c:30 kvasprintf+0x121/0x130 Call Trace: kvasprintf+0x121/0x130 kasprintf+0xa6/0xe0 bitmap_print_to_buf+0x89/0x100 core_siblings_list_read+0x7e/0xb0 kernfs_file_read_iter+0x15b/0x270 new_sync_read+0x153/0x260 vfs_read+0x215/0x290 ksys_read+0xb9/0x160 do_syscall_64+0x56/0x100 entry_SYSCALL_64_after_hwframe+0x78/0xe2 The call trace shows that kvasprintf() reported this warning during the printing of core_siblings_list. kvasprintf() has several steps: (1) First, calculate the length of the resulting formatted string. (2) Allocate a buffer based on the returned length. (3) Then, perform the actual string formatting. (4) Check whether the lengths of the formatted strings returned in steps (1) and (2) are consistent. If the core_cpumask is modified between steps (1) and (3), the lengths obtained in these two steps may not match. Indeed our test includes cpu hotplugging, which should modify core_cpumask while printing. To fix this issue, cache the cpumask into a temporary variable before calling cpumap_print_{list, cpumask}_to_buf(), to keep it unchanged during the printing process.

• CVE-2024-57924 — CVE-2024-57924 · CWE-617

  In the Linux kernel, the following vulnerability has been resolved: fs: relax assertions on failure to encode file handles Encoding file handles is usually performed by a filesystem >encode_fh() method that may fail for various reasons. The legacy users of exportfs_encode_fh(), namely, nfsd and name_to_handle_at(2) syscall are ready to cope with the possibility of failure to encode a file handle. There are a few other users of exportfs_encode_{fh,fid}() that currently have a WARN_ON() assertion when ->encode_fh() fails. Relax those assertions because they are wrong. The second linked bug report states commit 16aac5ad1fa9 ("ovl: support encoding non-decodable file handles") in v6.6 as the regressing commit, but this is not accurate. The aforementioned commit only increases the chances of the assertion and allows triggering the assertion with the reproducer using overlayfs, inotify and drop_caches. Triggering this assertion was always possible with other filesystems and other reasons of ->encode_fh() failures and more particularly, it was also possible with the exact same reproducer using overlayfs that is mounted with options index=on,nfs_export=on also on kernels < v6.6. Therefore, I am not listing the aforementioned commit as a Fixes commit. Backport hint: this patch will have a trivial conflict applying to v6.6.y, and other trivial conflicts applying to stable kernels < v6.6.

• CVE-2024-57973 — CVE-2024-57973 · CWE-190

  In the Linux kernel, the following vulnerability has been resolved: rdma/cxgb4: Prevent potential integer overflow on 32bit The "gl->tot_len" variable is controlled by the user. It comes from process_responses(). On 32bit systems, the "gl->tot_len + sizeof(struct cpl_pass_accept_req) + sizeof(struct rss_header)" addition could have an integer wrapping bug. Use size_add() to prevent this.

• CVE-2024-57977 — CVE-2024-57977 · CWE-667

  In the Linux kernel, the following vulnerability has been resolved: memcg: fix soft lockup in the OOM process A soft lockup issue was found in the product with about 56,000 tasks were in the OOM cgroup, it was traversing them when the soft lockup was triggered. watchdog: BUG: soft lockup - CPU#2 stuck for 23s! [VM Thread:1503066] CPU: 2 PID: 1503066 Comm: VM Thread Kdump: loaded Tainted: G Hardware name: Huawei Cloud OpenStack Nova, BIOS RIP: 0010:console_unlock+0x343/0x540 RSP: 0000:ffffb751447db9a0 EFLAGS: 00000247 ORIG_RAX: ffffffffffffff13 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 00000000ffffffff RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000247 RBP: ffffffffafc71f90 R08: 0000000000000000 R09: 0000000000000040 R10: 0000000000000080 R11: 0000000000000000 R12: ffffffffafc74bd0 R13: ffffffffaf60a220 R14: 0000000000000247 R15: 0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2fe6ad91f0 CR3: 00000004b2076003 CR4: 0000000000360ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: vprintk_emit+0x193/0x280 printk+0x52/0x6e dump_task+0x114/0x130 mem_cgroup_scan_tasks+0x76/0x100 dump_header+0x1fe/0x210 oom_kill_process+0xd1/0x100 out_of_memory+0x125/0x570 mem_cgroup_out_of_memory+0xb5/0xd0 try_charge+0x720/0x770 mem_cgroup_try_charge+0x86/0x180 mem_cgroup_try_charge_delay+0x1c/0x40 do_anonymous_page+0xb5/0x390 handle_mm_fault+0xc4/0x1f0 This is because thousands of processes are in the OOM cgroup, it takes a long time to traverse all of them. As a result, this lead to soft lockup in the OOM process. To fix this issue, call 'cond_resched' in the 'mem_cgroup_scan_tasks' function per 1000 iterations. For global OOM, call 'touch_softlockup_watchdog' per 1000 iterations to avoid this issue.

• CVE-2024-57979 — CVE-2024-57979 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: pps: Fix a use-after-free On a board running ntpd and gpsd, I'm seeing a consistent use-after-free in sys_exit() from gpsd when rebooting: pps pps1: removed ------------[ cut here ]------------ kobject: '(null)' (00000000db4bec24): is not initialized, yet kobject_put() is being called. WARNING: CPU: 2 PID: 440 at lib/kobject.c:734 kobject_put+0x120/0x150 CPU: 2 UID: 299 PID: 440 Comm: gpsd Not tainted 6.11.0-rc6-00308-gb31c44928842 #1 Hardware name: Raspberry Pi 4 Model B Rev 1.1 (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : kobject_put+0x120/0x150 lr : kobject_put+0x120/0x150 sp : ffffffc0803d3ae0 x29: ffffffc0803d3ae0 x28: ffffff8042dc9738 x27: 0000000000000001 x26: 0000000000000000 x25: ffffff8042dc9040 x24: ffffff8042dc9440 x23: ffffff80402a4620 x22: ffffff8042ef4bd0 x21: ffffff80405cb600 x20: 000000000008001b x19: ffffff8040b3b6e0 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 696e6920746f6e20 x14: 7369203a29343263 x13: 205d303434542020 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: kobject_put+0x120/0x150 cdev_put+0x20/0x3c __fput+0x2c4/0x2d8 ____fput+0x1c/0x38 task_work_run+0x70/0xfc do_exit+0x2a0/0x924 do_group_exit+0x34/0x90 get_signal+0x7fc/0x8c0 do_signal+0x128/0x13b4 do_notify_resume+0xdc/0x160 el0_svc+0xd4/0xf8 el0t_64_sync_handler+0x140/0x14c el0t_64_sync+0x190/0x194 ---[ end trace 0000000000000000 ]--- ...followed by more symptoms of corruption, with similar stacks: refcount_t: underflow; use-after-free. kernel BUG at lib/list_debug.c:62! Kernel panic - not syncing: Oops - BUG: Fatal exception This happens because pps_device_destruct() frees the pps_device with the embedded cdev immediately after calling cdev_del(), but, as the comment above cdev_del() notes, fops for previously opened cdevs are still callable even after cdev_del() returns. I think this bug has always been there: I can't explain why it suddenly started happening every time I reboot this particular board. In commit d953e0e837e6 ("pps: Fix a use-after free bug when unregistering a source."), George Spelvin suggested removing the embedded cdev. That seems like the simplest way to fix this, so I've implemented his suggestion, using __register_chrdev() with pps_idr becoming the source of truth for which minor corresponds to which device. But now that pps_idr defines userspace visibility instead of cdev_add(), we need to be sure the pps->dev refcount can't reach zero while userspace can still find it again. So, the idr_remove() call moves to pps_unregister_cdev(), and pps_idr now holds a reference to pps->dev. pps_core: source serial1 got cdev (251:1) <...> pps pps1: removed pps_core: unregistering pps1 pps_core: deallocating pps1

• CVE-2024-58011 — CVE-2024-58011 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: platform/x86: int3472: Check for adev == NULL Not all devices have an ACPI companion fwnode, so adev might be NULL. This can e.g. (theoretically) happen when a user manually binds one of the int3472 drivers to another i2c/platform device through sysfs. Add a check for adev not being set and return -ENODEV in that case to avoid a possible NULL pointer deref in skl_int3472_get_acpi_buffer().

• CVE-2024-58016 — CVE-2024-58016 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: safesetid: check size of policy writes syzbot attempts to write a buffer with a large size to a sysfs entry with writes handled by handle_policy_update(), triggering a warning in kmalloc. Check the size specified for write buffers before allocating. [PM: subject tweak]

• CVE-2024-58020 — CVE-2024-58020 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: Add NULL check in mt_input_configured devm_kasprintf() can return a NULL pointer on failure,but this returned value in mt_input_configured() is not checked. Add NULL check in mt_input_configured(), to handle kernel NULL pointer dereference error.

• CVE-2024-58056 — CVE-2024-58056 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: remoteproc: core: Fix ida_free call while not allocated In the rproc_alloc() function, on error, put_device(&rproc->dev) is called, leading to the call of the rproc_type_release() function. An error can occurs before ida_alloc is called. In such case in rproc_type_release(), the condition (rproc->index >= 0) is true as rproc->index has been initialized to 0. ida_free() is called reporting a warning: [ 4.181906] WARNING: CPU: 1 PID: 24 at lib/idr.c:525 ida_free+0x100/0x164 [ 4.186378] stm32-display-dsi 5a000000.dsi: Fixed dependency cycle(s) with /soc/dsi@5a000000/panel@0 [ 4.188854] ida_free called for id=0 which is not allocated. [ 4.198256] mipi-dsi 5a000000.dsi.0: Fixed dependency cycle(s) with /soc/dsi@5a000000 [ 4.203556] Modules linked in: panel_orisetech_otm8009a dw_mipi_dsi_stm(+) gpu_sched dw_mipi_dsi stm32_rproc stm32_crc32 stm32_ipcc(+) optee(+) [ 4.224307] CPU: 1 UID: 0 PID: 24 Comm: kworker/u10:0 Not tainted 6.12.0 #442 [ 4.231481] Hardware name: STM32 (Device Tree Support) [ 4.236627] Workqueue: events_unbound deferred_probe_work_func [ 4.242504] Call trace: [ 4.242522] unwind_backtrace from show_stack+0x10/0x14 [ 4.250218] show_stack from dump_stack_lvl+0x50/0x64 [ 4.255274] dump_stack_lvl from __warn+0x80/0x12c [ 4.260134] __warn from warn_slowpath_fmt+0x114/0x188 [ 4.265199] warn_slowpath_fmt from ida_free+0x100/0x164 [ 4.270565] ida_free from rproc_type_release+0x38/0x60 [ 4.275832] rproc_type_release from device_release+0x30/0xa0 [ 4.281601] device_release from kobject_put+0xc4/0x294 [ 4.286762] kobject_put from rproc_alloc.part.0+0x208/0x28c [ 4.292430] rproc_alloc.part.0 from devm_rproc_alloc+0x80/0xc4 [ 4.298393] devm_rproc_alloc from stm32_rproc_probe+0xd0/0x844 [stm32_rproc] [ 4.305575] stm32_rproc_probe [stm32_rproc] from platform_probe+0x5c/0xbc Calling ida_alloc earlier in rproc_alloc ensures that the rproc->index is properly set.

• CVE-2024-58058 — CVE-2024-58058 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: ubifs: skip dumping tnc tree when zroot is null Clearing slab cache will free all znode in memory and make c->zroot.znode = NULL, then dumping tnc tree will access c->zroot.znode which cause null pointer dereference.

• CVE-2024-58061 — CVE-2024-58061 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: prohibit deactivating all links In the internal API this calls this is a WARN_ON, but that should remain since internally we want to know about bugs that may cause this. Prevent deactivating all links in the debugfs write directly.

• CVE-2024-58086 — CVE-2024-58086 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Stop active perfmon if it is being destroyed If the active performance monitor (`v3d->active_perfmon`) is being destroyed, stop it first. Currently, the active perfmon is not stopped during destruction, leaving the `v3d->active_perfmon` pointer stale. This can lead to undefined behavior and instability. This patch ensures that the active perfmon is stopped before being destroyed, aligning with the behavior introduced in commit 7d1fd3638ee3 ("drm/v3d: Stop the active perfmon before being destroyed").

• CVE-2025-21645 — CVE-2025-21645 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: platform/x86/amd/pmc: Only disable IRQ1 wakeup where i8042 actually enabled it Wakeup for IRQ1 should be disabled only in cases where i8042 had actually enabled it, otherwise "wake_depth" for this IRQ will try to drop below zero and there will be an unpleasant WARN() logged: kernel: atkbd serio0: Disabling IRQ1 wakeup source to avoid platform firmware bug kernel: ------------[ cut here ]------------ kernel: Unbalanced IRQ 1 wake disable kernel: WARNING: CPU: 10 PID: 6431 at kernel/irq/manage.c:920 irq_set_irq_wake+0x147/0x1a0 The PMC driver uses DEFINE_SIMPLE_DEV_PM_OPS() to define its dev_pm_ops which sets amd_pmc_suspend_handler() to the .suspend, .freeze, and .poweroff handlers. i8042_pm_suspend(), however, is only set as the .suspend handler. Fix the issue by call PMC suspend handler only from the same set of dev_pm_ops handlers as i8042_pm_suspend(), which currently means just the .suspend handler. To reproduce this issue try hibernating (S4) the machine after a fresh boot without putting it into s2idle first. [ij: edited the commit message.]

• CVE-2025-21648 — CVE-2025-21648 · CWE-789

  In the Linux kernel, the following vulnerability has been resolved: netfilter: conntrack: clamp maximum hashtable size to INT_MAX Use INT_MAX as maximum size for the conntrack hashtable. Otherwise, it is possible to hit WARN_ON_ONCE in __kvmalloc_node_noprof() when resizing hashtable because __GFP_NOWARN is unset. See: 0708a0afe291 ("mm: Consider __GFP_NOWARN flag for oversized kvmalloc() calls") Note: hashtable resize is only possible from init_netns.

• CVE-2025-21655 — CVE-2025-21655 · CWE-362

  In the Linux kernel, the following vulnerability has been resolved: io_uring/eventfd: ensure io_eventfd_signal() defers another RCU period io_eventfd_do_signal() is invoked from an RCU callback, but when dropping the reference to the io_ev_fd, it calls io_eventfd_free() directly if the refcount drops to zero. This isn't correct, as any potential freeing of the io_ev_fd should be deferred another RCU grace period. Just call io_eventfd_put() rather than open-code the dec-and-test and free, which will correctly defer it another RCU grace period.

• CVE-2025-21676 — CVE-2025-21676 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: net: fec: handle page_pool_dev_alloc_pages error The fec_enet_update_cbd function calls page_pool_dev_alloc_pages but did not handle the case when it returned NULL. There was a WARN_ON(!new_page) but it would still proceed to use the NULL pointer and then crash. This case does seem somewhat rare but when the system is under memory pressure it can happen. One case where I can duplicate this with some frequency is when writing over a smbd share to a SATA HDD attached to an imx6q. Setting /proc/sys/vm/min_free_kbytes to higher values also seems to solve the problem for my test case. But it still seems wrong that the fec driver ignores the memory allocation error and can crash. This commit handles the allocation error by dropping the current packet.

• CVE-2025-21682 — CVE-2025-21682 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: eth: bnxt: always recalculate features after XDP clearing, fix null-deref Recalculate features when XDP is detached. Before: # ip li set dev eth0 xdp obj xdp_dummy.bpf.o sec xdp # ip li set dev eth0 xdp off # ethtool -k eth0 | grep gro rx-gro-hw: off [requested on] After: # ip li set dev eth0 xdp obj xdp_dummy.bpf.o sec xdp # ip li set dev eth0 xdp off # ethtool -k eth0 | grep gro rx-gro-hw: on The fact that HW-GRO doesn't get re-enabled automatically is just a minor annoyance. The real issue is that the features will randomly come back during another reconfiguration which just happens to invoke netdev_update_features(). The driver doesn't handle reconfiguring two things at a time very robustly. Starting with commit 98ba1d931f61 ("bnxt_en: Fix RSS logic in __bnxt_reserve_rings()") we only reconfigure the RSS hash table if the "effective" number of Rx rings has changed. If HW-GRO is enabled "effective" number of rings is 2x what user sees. So if we are in the bad state, with HW-GRO re-enablement "pending" after XDP off, and we lower the rings by / 2 - the HW-GRO rings doing 2x and the ethtool -L doing / 2 may cancel each other out, and the: if (old_rx_rings != bp->hw_resc.resv_rx_rings && condition in __bnxt_reserve_rings() will be false. The RSS map won't get updated, and we'll crash with: BUG: kernel NULL pointer dereference, address: 0000000000000168 RIP: 0010:__bnxt_hwrm_vnic_set_rss+0x13a/0x1a0 bnxt_hwrm_vnic_rss_cfg_p5+0x47/0x180 __bnxt_setup_vnic_p5+0x58/0x110 bnxt_init_nic+0xb72/0xf50 __bnxt_open_nic+0x40d/0xab0 bnxt_open_nic+0x2b/0x60 ethtool_set_channels+0x18c/0x1d0 As we try to access a freed ring. The issue is present since XDP support was added, really, but prior to commit 98ba1d931f61 ("bnxt_en: Fix RSS logic in __bnxt_reserve_rings()") it wasn't causing major issues.

• CVE-2025-21702 — CVE-2025-21702 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: pfifo_tail_enqueue: Drop new packet when sch->limit == 0 Expected behaviour: In case we reach scheduler's limit, pfifo_tail_enqueue() will drop a packet in scheduler's queue and decrease scheduler's qlen by one. Then, pfifo_tail_enqueue() enqueue new packet and increase scheduler's qlen by one. Finally, pfifo_tail_enqueue() return `NET_XMIT_CN` status code. Weird behaviour: In case we set `sch->limit == 0` and trigger pfifo_tail_enqueue() on a scheduler that has no packet, the 'drop a packet' step will do nothing. This means the scheduler's qlen still has value equal 0. Then, we continue to enqueue new packet and increase scheduler's qlen by one. In summary, we can leverage pfifo_tail_enqueue() to increase qlen by one and return `NET_XMIT_CN` status code. The problem is: Let's say we have two qdiscs: Qdisc_A and Qdisc_B. - Qdisc_A's type must have '->graft()' function to create parent/child relationship. Let's say Qdisc_A's type is `hfsc`. Enqueue packet to this qdisc will trigger `hfsc_enqueue`. - Qdisc_B's type is pfifo_head_drop. Enqueue packet to this qdisc will trigger `pfifo_tail_enqueue`. - Qdisc_B is configured to have `sch->limit == 0`. - Qdisc_A is configured to route the enqueued's packet to Qdisc_B. Enqueue packet through Qdisc_A will lead to: - hfsc_enqueue(Qdisc_A) -> pfifo_tail_enqueue(Qdisc_B) - Qdisc_B->q.qlen += 1 - pfifo_tail_enqueue() return `NET_XMIT_CN` - hfsc_enqueue() check for `NET_XMIT_SUCCESS` and see `NET_XMIT_CN` => hfsc_enqueue() don't increase qlen of Qdisc_A. The whole process lead to a situation where Qdisc_A->q.qlen == 0 and Qdisc_B->q.qlen == 1. Replace 'hfsc' with other type (for example: 'drr') still lead to the same problem. This violate the design where parent's qlen should equal to the sum of its childrens'qlen. Bug impact: This issue can be used for user->kernel privilege escalation when it is reachable.

• CVE-2025-21705 — CVE-2025-21705 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: mptcp: handle fastopen disconnect correctly Syzbot was able to trigger a data stream corruption: WARNING: CPU: 0 PID: 9846 at net/mptcp/protocol.c:1024 __mptcp_clean_una+0xddb/0xff0 net/mptcp/protocol.c:1024 Modules linked in: CPU: 0 UID: 0 PID: 9846 Comm: syz-executor351 Not tainted 6.13.0-rc2-syzkaller-00059-g00a5acdbf398 #0 Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 11/25/2024 RIP: 0010:__mptcp_clean_una+0xddb/0xff0 net/mptcp/protocol.c:1024 Code: fa ff ff 48 8b 4c 24 18 80 e1 07 fe c1 38 c1 0f 8c 8e fa ff ff 48 8b 7c 24 18 e8 e0 db 54 f6 e9 7f fa ff ff e8 e6 80 ee f5 90 <0f> 0b 90 4c 8b 6c 24 40 4d 89 f4 e9 04 f5 ff ff 44 89 f1 80 e1 07 RSP: 0018:ffffc9000c0cf400 EFLAGS: 00010293 RAX: ffffffff8bb0dd5a RBX: ffff888033f5d230 RCX: ffff888059ce8000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffc9000c0cf518 R08: ffffffff8bb0d1dd R09: 1ffff110170c8928 R10: dffffc0000000000 R11: ffffed10170c8929 R12: 0000000000000000 R13: ffff888033f5d220 R14: dffffc0000000000 R15: ffff8880592b8000 FS: 00007f6e866496c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f6e86f491a0 CR3: 00000000310e6000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __mptcp_clean_una_wakeup+0x7f/0x2d0 net/mptcp/protocol.c:1074 mptcp_release_cb+0x7cb/0xb30 net/mptcp/protocol.c:3493 release_sock+0x1aa/0x1f0 net/core/sock.c:3640 inet_wait_for_connect net/ipv4/af_inet.c:609 [inline] __inet_stream_connect+0x8bd/0xf30 net/ipv4/af_inet.c:703 mptcp_sendmsg_fastopen+0x2a2/0x530 net/mptcp/protocol.c:1755 mptcp_sendmsg+0x1884/0x1b10 net/mptcp/protocol.c:1830 sock_sendmsg_nosec net/socket.c:711 [inline] __sock_sendmsg+0x1a6/0x270 net/socket.c:726 ____sys_sendmsg+0x52a/0x7e0 net/socket.c:2583 ___sys_sendmsg net/socket.c:2637 [inline] __sys_sendmsg+0x269/0x350 net/socket.c:2669 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f6e86ebfe69 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 b1 1f 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f6e86649168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f6e86f491b8 RCX: 00007f6e86ebfe69 RDX: 0000000030004001 RSI: 0000000020000080 RDI: 0000000000000003 RBP: 00007f6e86f491b0 R08: 00007f6e866496c0 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6e86f491bc R13: 000000000000006e R14: 00007ffe445d9420 R15: 00007ffe445d9508 </TASK> The root cause is the bad handling of disconnect() generated internally by the MPTCP protocol in case of connect FASTOPEN errors. Address the issue increasing the socket disconnect counter even on such a case, to allow other threads waiting on the same socket lock to properly error out.

• CVE-2025-21706 — CVE-2025-21706 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: only set fullmesh for subflow endp With the in-kernel path-manager, it is possible to change the 'fullmesh' flag. The code in mptcp_pm_nl_fullmesh() expects to change it only on 'subflow' endpoints, to recreate more or less subflows using the linked address. Unfortunately, the set_flags() hook was a bit more permissive, and allowed 'implicit' endpoints to get the 'fullmesh' flag while it is not allowed before. That's what syzbot found, triggering the following warning: WARNING: CPU: 0 PID: 6499 at net/mptcp/pm_netlink.c:1496 __mark_subflow_endp_available net/mptcp/pm_netlink.c:1496 [inline] WARNING: CPU: 0 PID: 6499 at net/mptcp/pm_netlink.c:1496 mptcp_pm_nl_fullmesh net/mptcp/pm_netlink.c:1980 [inline] WARNING: CPU: 0 PID: 6499 at net/mptcp/pm_netlink.c:1496 mptcp_nl_set_flags net/mptcp/pm_netlink.c:2003 [inline] WARNING: CPU: 0 PID: 6499 at net/mptcp/pm_netlink.c:1496 mptcp_pm_nl_set_flags+0x974/0xdc0 net/mptcp/pm_netlink.c:2064 Modules linked in: CPU: 0 UID: 0 PID: 6499 Comm: syz.1.413 Not tainted 6.13.0-rc5-syzkaller-00172-gd1bf27c4e176 #0 Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:__mark_subflow_endp_available net/mptcp/pm_netlink.c:1496 [inline] RIP: 0010:mptcp_pm_nl_fullmesh net/mptcp/pm_netlink.c:1980 [inline] RIP: 0010:mptcp_nl_set_flags net/mptcp/pm_netlink.c:2003 [inline] RIP: 0010:mptcp_pm_nl_set_flags+0x974/0xdc0 net/mptcp/pm_netlink.c:2064 Code: 01 00 00 49 89 c5 e8 fb 45 e8 f5 e9 b8 fc ff ff e8 f1 45 e8 f5 4c 89 f7 be 03 00 00 00 e8 44 1d 0b f9 eb a0 e8 dd 45 e8 f5 90 <0f> 0b 90 e9 17 ff ff ff 89 d9 80 e1 07 38 c1 0f 8c c9 fc ff ff 48 RSP: 0018:ffffc9000d307240 EFLAGS: 00010293 RAX: ffffffff8bb72e03 RBX: 0000000000000000 RCX: ffff88807da88000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffc9000d307430 R08: ffffffff8bb72cf0 R09: 1ffff1100b842a5e R10: dffffc0000000000 R11: ffffed100b842a5f R12: ffff88801e2e5ac0 R13: ffff88805c214800 R14: ffff88805c2152e8 R15: 1ffff1100b842a5d FS: 00005555619f6500(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020002840 CR3: 00000000247e6000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> genl_family_rcv_msg_doit net/netlink/genetlink.c:1115 [inline] genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0xb14/0xec0 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x1e3/0x430 net/netlink/af_netlink.c:2542 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1321 [inline] netlink_unicast+0x7f6/0x990 net/netlink/af_netlink.c:1347 netlink_sendmsg+0x8e4/0xcb0 net/netlink/af_netlink.c:1891 sock_sendmsg_nosec net/socket.c:711 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:726 ____sys_sendmsg+0x52a/0x7e0 net/socket.c:2583 ___sys_sendmsg net/socket.c:2637 [inline] __sys_sendmsg+0x269/0x350 net/socket.c:2669 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f5fe8785d29 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fff571f5558 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f5fe8975fa0 RCX: 00007f5fe8785d29 RDX: 0000000000000000 RSI: 0000000020000480 RDI: 0000000000000007 RBP: 00007f5fe8801b08 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007f5fe8975fa0 R14: 00007f5fe8975fa0 R15: 000000 ---truncated---

• CVE-2025-21707 — CVE-2025-21707 · CWE-908

  In the Linux kernel, the following vulnerability has been resolved: mptcp: consolidate suboption status MPTCP maintains the received sub-options status is the bitmask carrying the received suboptions and in several bitfields carrying per suboption additional info. Zeroing the bitmask before parsing is not enough to ensure a consistent status, and the MPTCP code has to additionally clear some bitfiled depending on the actually parsed suboption. The above schema is fragile, and syzbot managed to trigger a path where a relevant bitfield is not cleared/initialized: BUG: KMSAN: uninit-value in __mptcp_expand_seq net/mptcp/options.c:1030 [inline] BUG: KMSAN: uninit-value in mptcp_expand_seq net/mptcp/protocol.h:864 [inline] BUG: KMSAN: uninit-value in ack_update_msk net/mptcp/options.c:1060 [inline] BUG: KMSAN: uninit-value in mptcp_incoming_options+0x2036/0x3d30 net/mptcp/options.c:1209 __mptcp_expand_seq net/mptcp/options.c:1030 [inline] mptcp_expand_seq net/mptcp/protocol.h:864 [inline] ack_update_msk net/mptcp/options.c:1060 [inline] mptcp_incoming_options+0x2036/0x3d30 net/mptcp/options.c:1209 tcp_data_queue+0xb4/0x7be0 net/ipv4/tcp_input.c:5233 tcp_rcv_established+0x1061/0x2510 net/ipv4/tcp_input.c:6264 tcp_v4_do_rcv+0x7f3/0x11a0 net/ipv4/tcp_ipv4.c:1916 tcp_v4_rcv+0x51df/0x5750 net/ipv4/tcp_ipv4.c:2351 ip_protocol_deliver_rcu+0x2a3/0x13d0 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x336/0x500 net/ipv4/ip_input.c:233 NF_HOOK include/linux/netfilter.h:314 [inline] ip_local_deliver+0x21f/0x490 net/ipv4/ip_input.c:254 dst_input include/net/dst.h:460 [inline] ip_rcv_finish+0x4a2/0x520 net/ipv4/ip_input.c:447 NF_HOOK include/linux/netfilter.h:314 [inline] ip_rcv+0xcd/0x380 net/ipv4/ip_input.c:567 __netif_receive_skb_one_core net/core/dev.c:5704 [inline] __netif_receive_skb+0x319/0xa00 net/core/dev.c:5817 process_backlog+0x4ad/0xa50 net/core/dev.c:6149 __napi_poll+0xe7/0x980 net/core/dev.c:6902 napi_poll net/core/dev.c:6971 [inline] net_rx_action+0xa5a/0x19b0 net/core/dev.c:7093 handle_softirqs+0x1a0/0x7c0 kernel/softirq.c:561 __do_softirq+0x14/0x1a kernel/softirq.c:595 do_softirq+0x9a/0x100 kernel/softirq.c:462 __local_bh_enable_ip+0x9f/0xb0 kernel/softirq.c:389 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:919 [inline] __dev_queue_xmit+0x2758/0x57d0 net/core/dev.c:4493 dev_queue_xmit include/linux/netdevice.h:3168 [inline] neigh_hh_output include/net/neighbour.h:523 [inline] neigh_output include/net/neighbour.h:537 [inline] ip_finish_output2+0x187c/0x1b70 net/ipv4/ip_output.c:236 __ip_finish_output+0x287/0x810 ip_finish_output+0x4b/0x600 net/ipv4/ip_output.c:324 NF_HOOK_COND include/linux/netfilter.h:303 [inline] ip_output+0x15f/0x3f0 net/ipv4/ip_output.c:434 dst_output include/net/dst.h:450 [inline] ip_local_out net/ipv4/ip_output.c:130 [inline] __ip_queue_xmit+0x1f2a/0x20d0 net/ipv4/ip_output.c:536 ip_queue_xmit+0x60/0x80 net/ipv4/ip_output.c:550 __tcp_transmit_skb+0x3cea/0x4900 net/ipv4/tcp_output.c:1468 tcp_transmit_skb net/ipv4/tcp_output.c:1486 [inline] tcp_write_xmit+0x3b90/0x9070 net/ipv4/tcp_output.c:2829 __tcp_push_pending_frames+0xc4/0x380 net/ipv4/tcp_output.c:3012 tcp_send_fin+0x9f6/0xf50 net/ipv4/tcp_output.c:3618 __tcp_close+0x140c/0x1550 net/ipv4/tcp.c:3130 __mptcp_close_ssk+0x74e/0x16f0 net/mptcp/protocol.c:2496 mptcp_close_ssk+0x26b/0x2c0 net/mptcp/protocol.c:2550 mptcp_pm_nl_rm_addr_or_subflow+0x635/0xd10 net/mptcp/pm_netlink.c:889 mptcp_pm_nl_rm_subflow_received net/mptcp/pm_netlink.c:924 [inline] mptcp_pm_flush_addrs_and_subflows net/mptcp/pm_netlink.c:1688 [inline] mptcp_nl_flush_addrs_list net/mptcp/pm_netlink.c:1709 [inline] mptcp_pm_nl_flush_addrs_doit+0xe10/0x1630 net/mptcp/pm_netlink.c:1750 genl_family_rcv_msg_doit net/netlink/genetlink.c:1115 [inline] ---truncated---

• CVE-2025-21718 — CVE-2025-21718 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: net: rose: fix timer races against user threads Rose timers only acquire the socket spinlock, without checking if the socket is owned by one user thread. Add a check and rearm the timers if needed. BUG: KASAN: slab-use-after-free in rose_timer_expiry+0x31d/0x360 net/rose/rose_timer.c:174 Read of size 2 at addr ffff88802f09b82a by task swapper/0/0 CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.13.0-rc5-syzkaller-00172-gd1bf27c4e176 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x169/0x550 mm/kasan/report.c:489 kasan_report+0x143/0x180 mm/kasan/report.c:602 rose_timer_expiry+0x31d/0x360 net/rose/rose_timer.c:174 call_timer_fn+0x187/0x650 kernel/time/timer.c:1793 expire_timers kernel/time/timer.c:1844 [inline] __run_timers kernel/time/timer.c:2418 [inline] __run_timer_base+0x66a/0x8e0 kernel/time/timer.c:2430 run_timer_base kernel/time/timer.c:2439 [inline] run_timer_softirq+0xb7/0x170 kernel/time/timer.c:2449 handle_softirqs+0x2d4/0x9b0 kernel/softirq.c:561 __do_softirq kernel/softirq.c:595 [inline] invoke_softirq kernel/softirq.c:435 [inline] __irq_exit_rcu+0xf7/0x220 kernel/softirq.c:662 irq_exit_rcu+0x9/0x30 kernel/softirq.c:678 instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1049 [inline] sysvec_apic_timer_interrupt+0xa6/0xc0 arch/x86/kernel/apic/apic.c:1049 </IRQ>

• CVE-2025-21731 — CVE-2025-21731 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: nbd: don't allow reconnect after disconnect Following process can cause nbd_config UAF: 1) grab nbd_config temporarily; 2) nbd_genl_disconnect() flush all recv_work() and release the initial reference: nbd_genl_disconnect nbd_disconnect_and_put nbd_disconnect flush_workqueue(nbd->recv_workq) if (test_and_clear_bit(NBD_RT_HAS_CONFIG_REF, ...)) nbd_config_put -> due to step 1), reference is still not zero 3) nbd_genl_reconfigure() queue recv_work() again; nbd_genl_reconfigure config = nbd_get_config_unlocked(nbd) if (!config) -> succeed if (!test_bit(NBD_RT_BOUND, ...)) -> succeed nbd_reconnect_socket queue_work(nbd->recv_workq, &args->work) 4) step 1) release the reference; 5) Finially, recv_work() will trigger UAF: recv_work nbd_config_put(nbd) -> nbd_config is freed atomic_dec(&config->recv_threads) -> UAF Fix the problem by clearing NBD_RT_BOUND in nbd_genl_disconnect(), so that nbd_genl_reconfigure() will fail.

• CVE-2025-21745 — CVE-2025-21745 · CWE-401

  In the Linux kernel, the following vulnerability has been resolved: blk-cgroup: Fix class @block_class's subsystem refcount leakage blkcg_fill_root_iostats() iterates over @block_class's devices by class_dev_iter_(init|next)(), but does not end iterating with class_dev_iter_exit(), so causes the class's subsystem refcount leakage. Fix by ending the iterating with class_dev_iter_exit().

• CVE-2025-21758 — CVE-2025-21758 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: ipv6: mcast: add RCU protection to mld_newpack() mld_newpack() can be called without RTNL or RCU being held. Note that we no longer can use sock_alloc_send_skb() because ipv6.igmp_sk uses GFP_KERNEL allocations which can sleep. Instead use alloc_skb() and charge the net->ipv6.igmp_sk socket under RCU protection.

• CVE-2025-21760 — CVE-2025-21760 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: ndisc: extend RCU protection in ndisc_send_skb() ndisc_send_skb() can be called without RTNL or RCU held. Acquire rcu_read_lock() earlier, so that we can use dev_net_rcu() and avoid a potential UAF.

• CVE-2025-21764 — CVE-2025-21764 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: ndisc: use RCU protection in ndisc_alloc_skb() ndisc_alloc_skb() can be called without RTNL or RCU being held. Add RCU protection to avoid possible UAF.

• CVE-2025-21765 — CVE-2025-21765 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: ipv6: use RCU protection in ip6_default_advmss() ip6_default_advmss() needs rcu protection to make sure the net structure it reads does not disappear.

• CVE-2025-21780 — CVE-2025-21780 · CWE-120

  In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: avoid buffer overflow attach in smu_sys_set_pp_table() It malicious user provides a small pptable through sysfs and then a bigger pptable, it may cause buffer overflow attack in function smu_sys_set_pp_table().

• CVE-2025-21795 — CVE-2025-21795 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: NFSD: fix hang in nfsd4_shutdown_callback If nfs4_client is in courtesy state then there is no point to send the callback. This causes nfsd4_shutdown_callback to hang since cl_cb_inflight is not 0. This hang lasts about 15 minutes until TCP notifies NFSD that the connection was dropped. This patch modifies nfsd4_run_cb_work to skip the RPC call if nfs4_client is in courtesy state.

• CVE-2025-21796 — CVE-2025-21796 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: nfsd: clear acl_access/acl_default after releasing them If getting acl_default fails, acl_access and acl_default will be released simultaneously. However, acl_access will still retain a pointer pointing to the released posix_acl, which will trigger a WARNING in nfs3svc_release_getacl like this: ------------[ cut here ]------------ refcount_t: underflow; use-after-free. WARNING: CPU: 26 PID: 3199 at lib/refcount.c:28 refcount_warn_saturate+0xb5/0x170 Modules linked in: CPU: 26 UID: 0 PID: 3199 Comm: nfsd Not tainted 6.12.0-rc6-00079-g04ae226af01f-dirty #8 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 RIP: 0010:refcount_warn_saturate+0xb5/0x170 Code: cc cc 0f b6 1d b3 20 a5 03 80 fb 01 0f 87 65 48 d8 00 83 e3 01 75 e4 48 c7 c7 c0 3b 9b 85 c6 05 97 20 a5 03 01 e8 fb 3e 30 ff <0f> 0b eb cd 0f b6 1d 8a3 RSP: 0018:ffffc90008637cd8 EFLAGS: 00010282 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff83904fde RDX: dffffc0000000000 RSI: 0000000000000008 RDI: ffff88871ed36380 RBP: ffff888158beeb40 R08: 0000000000000001 R09: fffff520010c6f56 R10: ffffc90008637ab7 R11: 0000000000000001 R12: 0000000000000001 R13: ffff888140e77400 R14: ffff888140e77408 R15: ffffffff858b42c0 FS: 0000000000000000(0000) GS:ffff88871ed00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000562384d32158 CR3: 000000055cc6a000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? refcount_warn_saturate+0xb5/0x170 ? __warn+0xa5/0x140 ? refcount_warn_saturate+0xb5/0x170 ? report_bug+0x1b1/0x1e0 ? handle_bug+0x53/0xa0 ? exc_invalid_op+0x17/0x40 ? asm_exc_invalid_op+0x1a/0x20 ? tick_nohz_tick_stopped+0x1e/0x40 ? refcount_warn_saturate+0xb5/0x170 ? refcount_warn_saturate+0xb5/0x170 nfs3svc_release_getacl+0xc9/0xe0 svc_process_common+0x5db/0xb60 ? __pfx_svc_process_common+0x10/0x10 ? __rcu_read_unlock+0x69/0xa0 ? __pfx_nfsd_dispatch+0x10/0x10 ? svc_xprt_received+0xa1/0x120 ? xdr_init_decode+0x11d/0x190 svc_process+0x2a7/0x330 svc_handle_xprt+0x69d/0x940 svc_recv+0x180/0x2d0 nfsd+0x168/0x200 ? __pfx_nfsd+0x10/0x10 kthread+0x1a2/0x1e0 ? kthread+0xf4/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x34/0x60 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Kernel panic - not syncing: kernel: panic_on_warn set ... Clear acl_access/acl_default after posix_acl_release is called to prevent UAF from being triggered.

• CVE-2025-21802 — CVE-2025-21802 · CWE-413

  In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix oops when unload drivers paralleling When unload hclge driver, it tries to disable sriov first for each ae_dev node from hnae3_ae_dev_list. If user unloads hns3 driver at the time, because it removes all the ae_dev nodes, and it may cause oops. But we can't simply use hnae3_common_lock for this. Because in the process flow of pci_disable_sriov(), it will trigger the remove flow of VF, which will also take hnae3_common_lock. To fixes it, introduce a new mutex to protect the unload process.

• CVE-2025-21814 — CVE-2025-21814 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: ptp: Ensure info->enable callback is always set The ioctl and sysfs handlers unconditionally call the ->enable callback. Not all drivers implement that callback, leading to NULL dereferences. Example of affected drivers: ptp_s390.c, ptp_vclock.c and ptp_mock.c. Instead use a dummy callback if no better was specified by the driver.

• CVE-2025-21846 — CVE-2025-21846 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: acct: perform last write from workqueue In [1] it was reported that the acct(2) system call can be used to trigger NULL deref in cases where it is set to write to a file that triggers an internal lookup. This can e.g., happen when pointing acc(2) to /sys/power/resume. At the point the where the write to this file happens the calling task has already exited and called exit_fs(). A lookup will thus trigger a NULL-deref when accessing current->fs. Reorganize the code so that the the final write happens from the workqueue but with the caller's credentials. This preserves the (strange) permission model and has almost no regression risk. This api should stop to exist though.

• CVE-2025-21853 — CVE-2025-21853 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bpf: avoid holding freeze_mutex during mmap operation We use map->freeze_mutex to prevent races between map_freeze() and memory mapping BPF map contents with writable permissions. The way we naively do this means we'll hold freeze_mutex for entire duration of all the mm and VMA manipulations, which is completely unnecessary. This can potentially also lead to deadlocks, as reported by syzbot in [0]. So, instead, hold freeze_mutex only during writeability checks, bump (proactively) "write active" count for the map, unlock the mutex and proceed with mmap logic. And only if something went wrong during mmap logic, then undo that "write active" counter increment. [0] https://lore.kernel.org/bpf/678dcbc9.050a0220.303755.0066.GAE@google.com/

• CVE-2025-21861 — CVE-2025-21861 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: mm/migrate_device: don't add folio to be freed to LRU in migrate_device_finalize() If migration succeeded, we called folio_migrate_flags()->mem_cgroup_migrate() to migrate the memcg from the old to the new folio. This will set memcg_data of the old folio to 0. Similarly, if migration failed, memcg_data of the dst folio is left unset. If we call folio_putback_lru() on such folios (memcg_data == 0), we will add the folio to be freed to the LRU, making memcg code unhappy. Running the hmm selftests: # ./hmm-tests ... # RUN hmm.hmm_device_private.migrate ... [ 102.078007][T14893] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x7ff27d200 pfn:0x13cc00 [ 102.079974][T14893] anon flags: 0x17ff00000020018(uptodate|dirty|swapbacked|node=0|zone=2|lastcpupid=0x7ff) [ 102.082037][T14893] raw: 017ff00000020018 dead000000000100 dead000000000122 ffff8881353896c9 [ 102.083687][T14893] raw: 00000007ff27d200 0000000000000000 00000001ffffffff 0000000000000000 [ 102.085331][T14893] page dumped because: VM_WARN_ON_ONCE_FOLIO(!memcg && !mem_cgroup_disabled()) [ 102.087230][T14893] ------------[ cut here ]------------ [ 102.088279][T14893] WARNING: CPU: 0 PID: 14893 at ./include/linux/memcontrol.h:726 folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.090478][T14893] Modules linked in: [ 102.091244][T14893] CPU: 0 UID: 0 PID: 14893 Comm: hmm-tests Not tainted 6.13.0-09623-g6c216bc522fd #151 [ 102.093089][T14893] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 [ 102.094848][T14893] RIP: 0010:folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.096104][T14893] Code: ... [ 102.099908][T14893] RSP: 0018:ffffc900236c37b0 EFLAGS: 00010293 [ 102.101152][T14893] RAX: 0000000000000000 RBX: ffffea0004f30000 RCX: ffffffff8183f426 [ 102.102684][T14893] RDX: ffff8881063cb880 RSI: ffffffff81b8117f RDI: ffff8881063cb880 [ 102.104227][T14893] RBP: 0000000000000000 R08: 0000000000000005 R09: 0000000000000000 [ 102.105757][T14893] R10: 0000000000000001 R11: 0000000000000002 R12: ffffc900236c37d8 [ 102.107296][T14893] R13: ffff888277a2bcb0 R14: 000000000000001f R15: 0000000000000000 [ 102.108830][T14893] FS: 00007ff27dbdd740(0000) GS:ffff888277a00000(0000) knlGS:0000000000000000 [ 102.110643][T14893] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 102.111924][T14893] CR2: 00007ff27d400000 CR3: 000000010866e000 CR4: 0000000000750ef0 [ 102.113478][T14893] PKRU: 55555554 [ 102.114172][T14893] Call Trace: [ 102.114805][T14893] <TASK> [ 102.115397][T14893] ? folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.116547][T14893] ? __warn.cold+0x110/0x210 [ 102.117461][T14893] ? folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.118667][T14893] ? report_bug+0x1b9/0x320 [ 102.119571][T14893] ? handle_bug+0x54/0x90 [ 102.120494][T14893] ? exc_invalid_op+0x17/0x50 [ 102.121433][T14893] ? asm_exc_invalid_op+0x1a/0x20 [ 102.122435][T14893] ? __wake_up_klogd.part.0+0x76/0xd0 [ 102.123506][T14893] ? dump_page+0x4f/0x60 [ 102.124352][T14893] ? folio_lruvec_lock_irqsave+0x10e/0x170 [ 102.125500][T14893] folio_batch_move_lru+0xd4/0x200 [ 102.126577][T14893] ? __pfx_lru_add+0x10/0x10 [ 102.127505][T14893] __folio_batch_add_and_move+0x391/0x720 [ 102.128633][T14893] ? __pfx_lru_add+0x10/0x10 [ 102.129550][T14893] folio_putback_lru+0x16/0x80 [ 102.130564][T14893] migrate_device_finalize+0x9b/0x530 [ 102.131640][T14893] dmirror_migrate_to_device.constprop.0+0x7c5/0xad0 [ 102.133047][T14893] dmirror_fops_unlocked_ioctl+0x89b/0xc80 Likely, nothing else goes wrong: putting the last folio reference will remove the folio from the LRU again. So besides memcg complaining, adding the folio to be freed to the LRU is just an unnecessary step. The new flow resembles what we have in migrate_folio_move(): add the dst to the lru, rem ---truncated---

• CVE-2025-21864 — CVE-2025-21864 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: tcp: drop secpath at the same time as we currently drop dst Xiumei reported hitting the WARN in xfrm6_tunnel_net_exit while running tests that boil down to: - create a pair of netns - run a basic TCP test over ipcomp6 - delete the pair of netns The xfrm_state found on spi_byaddr was not deleted at the time we delete the netns, because we still have a reference on it. This lingering reference comes from a secpath (which holds a ref on the xfrm_state), which is still attached to an skb. This skb is not leaked, it ends up on sk_receive_queue and then gets defer-free'd by skb_attempt_defer_free. The problem happens when we defer freeing an skb (push it on one CPU's defer_list), and don't flush that list before the netns is deleted. In that case, we still have a reference on the xfrm_state that we don't expect at this point. We already drop the skb's dst in the TCP receive path when it's no longer needed, so let's also drop the secpath. At this point, tcp_filter has already called into the LSM hooks that may require the secpath, so it should not be needed anymore. However, in some of those places, the MPTCP extension has just been attached to the skb, so we cannot simply drop all extensions.

• CVE-2025-21867 — CVE-2025-21867 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: bpf, test_run: Fix use-after-free issue in eth_skb_pkt_type() KMSAN reported a use-after-free issue in eth_skb_pkt_type()[1]. The cause of the issue was that eth_skb_pkt_type() accessed skb's data that didn't contain an Ethernet header. This occurs when bpf_prog_test_run_xdp() passes an invalid value as the user_data argument to bpf_test_init(). Fix this by returning an error when user_data is less than ETH_HLEN in bpf_test_init(). Additionally, remove the check for "if (user_size > size)" as it is unnecessary. [1] BUG: KMSAN: use-after-free in eth_skb_pkt_type include/linux/etherdevice.h:627 [inline] BUG: KMSAN: use-after-free in eth_type_trans+0x4ee/0x980 net/ethernet/eth.c:165 eth_skb_pkt_type include/linux/etherdevice.h:627 [inline] eth_type_trans+0x4ee/0x980 net/ethernet/eth.c:165 __xdp_build_skb_from_frame+0x5a8/0xa50 net/core/xdp.c:635 xdp_recv_frames net/bpf/test_run.c:272 [inline] xdp_test_run_batch net/bpf/test_run.c:361 [inline] bpf_test_run_xdp_live+0x2954/0x3330 net/bpf/test_run.c:390 bpf_prog_test_run_xdp+0x148e/0x1b10 net/bpf/test_run.c:1318 bpf_prog_test_run+0x5b7/0xa30 kernel/bpf/syscall.c:4371 __sys_bpf+0x6a6/0xe20 kernel/bpf/syscall.c:5777 __do_sys_bpf kernel/bpf/syscall.c:5866 [inline] __se_sys_bpf kernel/bpf/syscall.c:5864 [inline] __x64_sys_bpf+0xa4/0xf0 kernel/bpf/syscall.c:5864 x64_sys_call+0x2ea0/0x3d90 arch/x86/include/generated/asm/syscalls_64.h:322 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd9/0x1d0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: free_pages_prepare mm/page_alloc.c:1056 [inline] free_unref_page+0x156/0x1320 mm/page_alloc.c:2657 __free_pages+0xa3/0x1b0 mm/page_alloc.c:4838 bpf_ringbuf_free kernel/bpf/ringbuf.c:226 [inline] ringbuf_map_free+0xff/0x1e0 kernel/bpf/ringbuf.c:235 bpf_map_free kernel/bpf/syscall.c:838 [inline] bpf_map_free_deferred+0x17c/0x310 kernel/bpf/syscall.c:862 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xa2b/0x1b60 kernel/workqueue.c:3310 worker_thread+0xedf/0x1550 kernel/workqueue.c:3391 kthread+0x535/0x6b0 kernel/kthread.c:389 ret_from_fork+0x6e/0x90 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 CPU: 1 UID: 0 PID: 17276 Comm: syz.1.16450 Not tainted 6.12.0-05490-g9bb88c659673 #8 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014

• CVE-2025-21875 — CVE-2025-21875 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: mptcp: always handle address removal under msk socket lock Syzkaller reported a lockdep splat in the PM control path: WARNING: CPU: 0 PID: 6693 at ./include/net/sock.h:1711 sock_owned_by_me include/net/sock.h:1711 [inline] WARNING: CPU: 0 PID: 6693 at ./include/net/sock.h:1711 msk_owned_by_me net/mptcp/protocol.h:363 [inline] WARNING: CPU: 0 PID: 6693 at ./include/net/sock.h:1711 mptcp_pm_nl_addr_send_ack+0x57c/0x610 net/mptcp/pm_netlink.c:788 Modules linked in: CPU: 0 UID: 0 PID: 6693 Comm: syz.0.205 Not tainted 6.14.0-rc2-syzkaller-00303-gad1b832bf1cf #0 Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 12/27/2024 RIP: 0010:sock_owned_by_me include/net/sock.h:1711 [inline] RIP: 0010:msk_owned_by_me net/mptcp/protocol.h:363 [inline] RIP: 0010:mptcp_pm_nl_addr_send_ack+0x57c/0x610 net/mptcp/pm_netlink.c:788 Code: 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc e8 ca 7b d3 f5 eb b9 e8 c3 7b d3 f5 90 0f 0b 90 e9 dd fb ff ff e8 b5 7b d3 f5 90 <0f> 0b 90 e9 3e fb ff ff 44 89 f1 80 e1 07 38 c1 0f 8c eb fb ff ff RSP: 0000:ffffc900034f6f60 EFLAGS: 00010283 RAX: ffffffff8bee3c2b RBX: 0000000000000001 RCX: 0000000000080000 RDX: ffffc90004d42000 RSI: 000000000000a407 RDI: 000000000000a408 RBP: ffffc900034f7030 R08: ffffffff8bee37f6 R09: 0100000000000000 R10: dffffc0000000000 R11: ffffed100bcc62e4 R12: ffff88805e6316e0 R13: ffff88805e630c00 R14: dffffc0000000000 R15: ffff88805e630c00 FS: 00007f7e9a7e96c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b2fd18ff8 CR3: 0000000032c24000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> mptcp_pm_remove_addr+0x103/0x1d0 net/mptcp/pm.c:59 mptcp_pm_remove_anno_addr+0x1f4/0x2f0 net/mptcp/pm_netlink.c:1486 mptcp_nl_remove_subflow_and_signal_addr net/mptcp/pm_netlink.c:1518 [inline] mptcp_pm_nl_del_addr_doit+0x118d/0x1af0 net/mptcp/pm_netlink.c:1629 genl_family_rcv_msg_doit net/netlink/genetlink.c:1115 [inline] genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0xb1f/0xec0 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x206/0x480 net/netlink/af_netlink.c:2543 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1322 [inline] netlink_unicast+0x7f6/0x990 net/netlink/af_netlink.c:1348 netlink_sendmsg+0x8de/0xcb0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:718 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:733 ____sys_sendmsg+0x53a/0x860 net/socket.c:2573 ___sys_sendmsg net/socket.c:2627 [inline] __sys_sendmsg+0x269/0x350 net/socket.c:2659 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f7e9998cde9 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f7e9a7e9038 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f7e99ba5fa0 RCX: 00007f7e9998cde9 RDX: 000000002000c094 RSI: 0000400000000000 RDI: 0000000000000007 RBP: 00007f7e99a0e2a0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 00007f7e99ba5fa0 R15: 00007fff49231088 Indeed the PM can try to send a RM_ADDR over a msk without acquiring first the msk socket lock. The bugged code-path comes from an early optimization: when there are no subflows, the PM should (usually) not send RM_ADDR notifications. The above statement is incorrect, as without locks another process could concur ---truncated---

• CVE-2025-21887 — CVE-2025-21887 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: ovl: fix UAF in ovl_dentry_update_reval by moving dput() in ovl_link_up The issue was caused by dput(upper) being called before ovl_dentry_update_reval(), while upper->d_flags was still accessed in ovl_dentry_remote(). Move dput(upper) after its last use to prevent use-after-free. BUG: KASAN: slab-use-after-free in ovl_dentry_remote fs/overlayfs/util.c:162 [inline] BUG: KASAN: slab-use-after-free in ovl_dentry_update_reval+0xd2/0xf0 fs/overlayfs/util.c:167 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:114 print_address_description mm/kasan/report.c:377 [inline] print_report+0xc3/0x620 mm/kasan/report.c:488 kasan_report+0xd9/0x110 mm/kasan/report.c:601 ovl_dentry_remote fs/overlayfs/util.c:162 [inline] ovl_dentry_update_reval+0xd2/0xf0 fs/overlayfs/util.c:167 ovl_link_up fs/overlayfs/copy_up.c:610 [inline] ovl_copy_up_one+0x2105/0x3490 fs/overlayfs/copy_up.c:1170 ovl_copy_up_flags+0x18d/0x200 fs/overlayfs/copy_up.c:1223 ovl_rename+0x39e/0x18c0 fs/overlayfs/dir.c:1136 vfs_rename+0xf84/0x20a0 fs/namei.c:4893 ... </TASK>

• CVE-2025-21913 — CVE-2025-21913 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: x86/amd_nb: Use rdmsr_safe() in amd_get_mmconfig_range() Xen doesn't offer MSR_FAM10H_MMIO_CONF_BASE to all guests. This results in the following warning: unchecked MSR access error: RDMSR from 0xc0010058 at rIP: 0xffffffff8101d19f (xen_do_read_msr+0x7f/0xa0) Call Trace: xen_read_msr+0x1e/0x30 amd_get_mmconfig_range+0x2b/0x80 quirk_amd_mmconfig_area+0x28/0x100 pnp_fixup_device+0x39/0x50 __pnp_add_device+0xf/0x150 pnp_add_device+0x3d/0x100 pnpacpi_add_device_handler+0x1f9/0x280 acpi_ns_get_device_callback+0x104/0x1c0 acpi_ns_walk_namespace+0x1d0/0x260 acpi_get_devices+0x8a/0xb0 pnpacpi_init+0x50/0x80 do_one_initcall+0x46/0x2e0 kernel_init_freeable+0x1da/0x2f0 kernel_init+0x16/0x1b0 ret_from_fork+0x30/0x50 ret_from_fork_asm+0x1b/0x30 based on quirks for a "PNP0c01" device. Treating MMCFG as disabled is the right course of action, so no change is needed there. This was most likely exposed by fixing the Xen MSR accessors to not be silently-safe.

• CVE-2025-21919 — CVE-2025-21919 · CWE-787

  In the Linux kernel, the following vulnerability has been resolved: sched/fair: Fix potential memory corruption in child_cfs_rq_on_list child_cfs_rq_on_list attempts to convert a 'prev' pointer to a cfs_rq. This 'prev' pointer can originate from struct rq's leaf_cfs_rq_list, making the conversion invalid and potentially leading to memory corruption. Depending on the relative positions of leaf_cfs_rq_list and the task group (tg) pointer within the struct, this can cause a memory fault or access garbage data. The issue arises in list_add_leaf_cfs_rq, where both cfs_rq->leaf_cfs_rq_list and rq->leaf_cfs_rq_list are added to the same leaf list. Also, rq->tmp_alone_branch can be set to rq->leaf_cfs_rq_list. This adds a check `if (prev == &rq->leaf_cfs_rq_list)` after the main conditional in child_cfs_rq_on_list. This ensures that the container_of operation will convert a correct cfs_rq struct. This check is sufficient because only cfs_rqs on the same CPU are added to the list, so verifying the 'prev' pointer against the current rq's list head is enough. Fixes a potential memory corruption issue that due to current struct layout might not be manifesting as a crash but could lead to unpredictable behavior when the layout changes.

• CVE-2025-21925 — CVE-2025-21925 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: llc: do not use skb_get() before dev_queue_xmit() syzbot is able to crash hosts [1], using llc and devices not supporting IFF_TX_SKB_SHARING. In this case, e1000 driver calls eth_skb_pad(), while the skb is shared. Simply replace skb_get() by skb_clone() in net/llc/llc_s_ac.c Note that e1000 driver might have an issue with pktgen, because it does not clear IFF_TX_SKB_SHARING, this is an orthogonal change. We need to audit other skb_get() uses in net/llc. [1] kernel BUG at net/core/skbuff.c:2178 ! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI CPU: 0 UID: 0 PID: 16371 Comm: syz.2.2764 Not tainted 6.14.0-rc4-syzkaller-00052-gac9c34d1e45a #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:pskb_expand_head+0x6ce/0x1240 net/core/skbuff.c:2178 Call Trace: <TASK> __skb_pad+0x18a/0x610 net/core/skbuff.c:2466 __skb_put_padto include/linux/skbuff.h:3843 [inline] skb_put_padto include/linux/skbuff.h:3862 [inline] eth_skb_pad include/linux/etherdevice.h:656 [inline] e1000_xmit_frame+0x2d99/0x5800 drivers/net/ethernet/intel/e1000/e1000_main.c:3128 __netdev_start_xmit include/linux/netdevice.h:5151 [inline] netdev_start_xmit include/linux/netdevice.h:5160 [inline] xmit_one net/core/dev.c:3806 [inline] dev_hard_start_xmit+0x9a/0x7b0 net/core/dev.c:3822 sch_direct_xmit+0x1ae/0xc30 net/sched/sch_generic.c:343 __dev_xmit_skb net/core/dev.c:4045 [inline] __dev_queue_xmit+0x13d4/0x43e0 net/core/dev.c:4621 dev_queue_xmit include/linux/netdevice.h:3313 [inline] llc_sap_action_send_test_c+0x268/0x320 net/llc/llc_s_ac.c:144 llc_exec_sap_trans_actions net/llc/llc_sap.c:153 [inline] llc_sap_next_state net/llc/llc_sap.c:182 [inline] llc_sap_state_process+0x239/0x510 net/llc/llc_sap.c:209 llc_ui_sendmsg+0xd0d/0x14e0 net/llc/af_llc.c:993 sock_sendmsg_nosec net/socket.c:718 [inline]

• CVE-2025-21926 — CVE-2025-21926 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: net: gso: fix ownership in __udp_gso_segment In __udp_gso_segment the skb destructor is removed before segmenting the skb but the socket reference is kept as-is. This is an issue if the original skb is later orphaned as we can hit the following bug: kernel BUG at ./include/linux/skbuff.h:3312! (skb_orphan) RIP: 0010:ip_rcv_core+0x8b2/0xca0 Call Trace: ip_rcv+0xab/0x6e0 __netif_receive_skb_one_core+0x168/0x1b0 process_backlog+0x384/0x1100 __napi_poll.constprop.0+0xa1/0x370 net_rx_action+0x925/0xe50 The above can happen following a sequence of events when using OpenVSwitch, when an OVS_ACTION_ATTR_USERSPACE action precedes an OVS_ACTION_ATTR_OUTPUT action: 1. OVS_ACTION_ATTR_USERSPACE is handled (in do_execute_actions): the skb goes through queue_gso_packets and then __udp_gso_segment, where its destructor is removed. 2. The segments' data are copied and sent to userspace. 3. OVS_ACTION_ATTR_OUTPUT is handled (in do_execute_actions) and the same original skb is sent to its path. 4. If it later hits skb_orphan, we hit the bug. Fix this by also removing the reference to the socket in __udp_gso_segment.

• CVE-2025-21938 — CVE-2025-21938 · CWE-362

  In the Linux kernel, the following vulnerability has been resolved: mptcp: fix 'scheduling while atomic' in mptcp_pm_nl_append_new_local_addr If multiple connection requests attempt to create an implicit mptcp endpoint in parallel, more than one caller may end up in mptcp_pm_nl_append_new_local_addr because none found the address in local_addr_list during their call to mptcp_pm_nl_get_local_id. In this case, the concurrent new_local_addr calls may delete the address entry created by the previous caller. These deletes use synchronize_rcu, but this is not permitted in some of the contexts where this function may be called. During packet recv, the caller may be in a rcu read critical section and have preemption disabled. An example stack: BUG: scheduling while atomic: swapper/2/0/0x00000302 Call Trace: <IRQ> dump_stack_lvl (lib/dump_stack.c:117 (discriminator 1)) dump_stack (lib/dump_stack.c:124) __schedule_bug (kernel/sched/core.c:5943) schedule_debug.constprop.0 (arch/x86/include/asm/preempt.h:33 kernel/sched/core.c:5970) __schedule (arch/x86/include/asm/jump_label.h:27 include/linux/jump_label.h:207 kernel/sched/features.h:29 kernel/sched/core.c:6621) schedule (arch/x86/include/asm/preempt.h:84 kernel/sched/core.c:6804 kernel/sched/core.c:6818) schedule_timeout (kernel/time/timer.c:2160) wait_for_completion (kernel/sched/completion.c:96 kernel/sched/completion.c:116 kernel/sched/completion.c:127 kernel/sched/completion.c:148) __wait_rcu_gp (include/linux/rcupdate.h:311 kernel/rcu/update.c:444) synchronize_rcu (kernel/rcu/tree.c:3609) mptcp_pm_nl_append_new_local_addr (net/mptcp/pm_netlink.c:966 net/mptcp/pm_netlink.c:1061) mptcp_pm_nl_get_local_id (net/mptcp/pm_netlink.c:1164) mptcp_pm_get_local_id (net/mptcp/pm.c:420) subflow_check_req (net/mptcp/subflow.c:98 net/mptcp/subflow.c:213) subflow_v4_route_req (net/mptcp/subflow.c:305) tcp_conn_request (net/ipv4/tcp_input.c:7216) subflow_v4_conn_request (net/mptcp/subflow.c:651) tcp_rcv_state_process (net/ipv4/tcp_input.c:6709) tcp_v4_do_rcv (net/ipv4/tcp_ipv4.c:1934) tcp_v4_rcv (net/ipv4/tcp_ipv4.c:2334) ip_protocol_deliver_rcu (net/ipv4/ip_input.c:205 (discriminator 1)) ip_local_deliver_finish (include/linux/rcupdate.h:813 net/ipv4/ip_input.c:234) ip_local_deliver (include/linux/netfilter.h:314 include/linux/netfilter.h:308 net/ipv4/ip_input.c:254) ip_sublist_rcv_finish (include/net/dst.h:461 net/ipv4/ip_input.c:580) ip_sublist_rcv (net/ipv4/ip_input.c:640) ip_list_rcv (net/ipv4/ip_input.c:675) __netif_receive_skb_list_core (net/core/dev.c:5583 net/core/dev.c:5631) netif_receive_skb_list_internal (net/core/dev.c:5685 net/core/dev.c:5774) napi_complete_done (include/linux/list.h:37 include/net/gro.h:449 include/net/gro.h:444 net/core/dev.c:6114) igb_poll (drivers/net/ethernet/intel/igb/igb_main.c:8244) igb __napi_poll (net/core/dev.c:6582) net_rx_action (net/core/dev.c:6653 net/core/dev.c:6787) handle_softirqs (kernel/softirq.c:553) __irq_exit_rcu (kernel/softirq.c:588 kernel/softirq.c:427 kernel/softirq.c:636) irq_exit_rcu (kernel/softirq.c:651) common_interrupt (arch/x86/kernel/irq.c:247 (discriminator 14)) </IRQ> This problem seems particularly prevalent if the user advertises an endpoint that has a different external vs internal address. In the case where the external address is advertised and multiple connections already exist, multiple subflow SYNs arrive in parallel which tends to trigger the race during creation of the first local_addr_list entries which have the internal address instead. Fix by skipping the replacement of an existing implicit local address if called via mptcp_pm_nl_get_local_id.

• CVE-2025-21959 — CVE-2025-21959 · CWE-908

  In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conncount: Fully initialize struct nf_conncount_tuple in insert_tree() Since commit b36e4523d4d5 ("netfilter: nf_conncount: fix garbage collection confirm race"), `cpu` and `jiffies32` were introduced to the struct nf_conncount_tuple. The commit made nf_conncount_add() initialize `conn->cpu` and `conn->jiffies32` when allocating the struct. In contrast, count_tree() was not changed to initialize them. By commit 34848d5c896e ("netfilter: nf_conncount: Split insert and traversal"), count_tree() was split and the relevant allocation code now resides in insert_tree(). Initialize `conn->cpu` and `conn->jiffies32` in insert_tree(). BUG: KMSAN: uninit-value in find_or_evict net/netfilter/nf_conncount.c:117 [inline] BUG: KMSAN: uninit-value in __nf_conncount_add+0xd9c/0x2850 net/netfilter/nf_conncount.c:143 find_or_evict net/netfilter/nf_conncount.c:117 [inline] __nf_conncount_add+0xd9c/0x2850 net/netfilter/nf_conncount.c:143 count_tree net/netfilter/nf_conncount.c:438 [inline] nf_conncount_count+0x82f/0x1e80 net/netfilter/nf_conncount.c:521 connlimit_mt+0x7f6/0xbd0 net/netfilter/xt_connlimit.c:72 __nft_match_eval net/netfilter/nft_compat.c:403 [inline] nft_match_eval+0x1a5/0x300 net/netfilter/nft_compat.c:433 expr_call_ops_eval net/netfilter/nf_tables_core.c:240 [inline] nft_do_chain+0x426/0x2290 net/netfilter/nf_tables_core.c:288 nft_do_chain_ipv4+0x1a5/0x230 net/netfilter/nft_chain_filter.c:23 nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline] nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626 nf_hook_slow_list+0x24d/0x860 net/netfilter/core.c:663 NF_HOOK_LIST include/linux/netfilter.h:350 [inline] ip_sublist_rcv+0x17b7/0x17f0 net/ipv4/ip_input.c:633 ip_list_rcv+0x9ef/0xa40 net/ipv4/ip_input.c:669 __netif_receive_skb_list_ptype net/core/dev.c:5936 [inline] __netif_receive_skb_list_core+0x15c5/0x1670 net/core/dev.c:5983 __netif_receive_skb_list net/core/dev.c:6035 [inline] netif_receive_skb_list_internal+0x1085/0x1700 net/core/dev.c:6126 netif_receive_skb_list+0x5a/0x460 net/core/dev.c:6178 xdp_recv_frames net/bpf/test_run.c:280 [inline] xdp_test_run_batch net/bpf/test_run.c:361 [inline] bpf_test_run_xdp_live+0x2e86/0x3480 net/bpf/test_run.c:390 bpf_prog_test_run_xdp+0xf1d/0x1ae0 net/bpf/test_run.c:1316 bpf_prog_test_run+0x5e5/0xa30 kernel/bpf/syscall.c:4407 __sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5813 __do_sys_bpf kernel/bpf/syscall.c:5902 [inline] __se_sys_bpf kernel/bpf/syscall.c:5900 [inline] __ia32_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5900 ia32_sys_call+0x394d/0x4180 arch/x86/include/generated/asm/syscalls_32.h:358 do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline] __do_fast_syscall_32+0xb0/0x110 arch/x86/entry/common.c:387 do_fast_syscall_32+0x38/0x80 arch/x86/entry/common.c:412 do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:450 entry_SYSENTER_compat_after_hwframe+0x84/0x8e Uninit was created at: slab_post_alloc_hook mm/slub.c:4121 [inline] slab_alloc_node mm/slub.c:4164 [inline] kmem_cache_alloc_noprof+0x915/0xe10 mm/slub.c:4171 insert_tree net/netfilter/nf_conncount.c:372 [inline] count_tree net/netfilter/nf_conncount.c:450 [inline] nf_conncount_count+0x1415/0x1e80 net/netfilter/nf_conncount.c:521 connlimit_mt+0x7f6/0xbd0 net/netfilter/xt_connlimit.c:72 __nft_match_eval net/netfilter/nft_compat.c:403 [inline] nft_match_eval+0x1a5/0x300 net/netfilter/nft_compat.c:433 expr_call_ops_eval net/netfilter/nf_tables_core.c:240 [inline] nft_do_chain+0x426/0x2290 net/netfilter/nf_tables_core.c:288 nft_do_chain_ipv4+0x1a5/0x230 net/netfilter/nft_chain_filter.c:23 nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline] nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626 nf_hook_slow_list+0x24d/0x860 net/netfilter/core.c:663 NF_HOOK_LIST include/linux/netfilter.h:350 [inline] ip_sublist_rcv+0x17b7/0x17f0 net/ipv4/ip_input.c:633 ip_list_rcv+0x9ef/0xa40 net/ip ---truncated---

• CVE-2025-21999 — CVE-2025-21999 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: proc: fix UAF in proc_get_inode() Fix race between rmmod and /proc/XXX's inode instantiation. The bug is that pde->proc_ops don't belong to /proc, it belongs to a module, therefore dereferencing it after /proc entry has been registered is a bug unless use_pde/unuse_pde() pair has been used. use_pde/unuse_pde can be avoided (2 atomic ops!) because pde->proc_ops never changes so information necessary for inode instantiation can be saved _before_ proc_register() in PDE itself and used later, avoiding pde->proc_ops->... dereference. rmmod lookup sys_delete_module proc_lookup_de pde_get(de); proc_get_inode(dir->i_sb, de); mod->exit() proc_remove remove_proc_subtree proc_entry_rundown(de); free_module(mod); if (S_ISREG(inode->i_mode)) if (de->proc_ops->proc_read_iter) --> As module is already freed, will trigger UAF BUG: unable to handle page fault for address: fffffbfff80a702b PGD 817fc4067 P4D 817fc4067 PUD 817fc0067 PMD 102ef4067 PTE 0 Oops: Oops: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 26 UID: 0 PID: 2667 Comm: ls Tainted: G Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) RIP: 0010:proc_get_inode+0x302/0x6e0 RSP: 0018:ffff88811c837998 EFLAGS: 00010a06 RAX: dffffc0000000000 RBX: ffffffffc0538140 RCX: 0000000000000007 RDX: 1ffffffff80a702b RSI: 0000000000000001 RDI: ffffffffc0538158 RBP: ffff8881299a6000 R08: 0000000067bbe1e5 R09: 1ffff11023906f20 R10: ffffffffb560ca07 R11: ffffffffb2b43a58 R12: ffff888105bb78f0 R13: ffff888100518048 R14: ffff8881299a6004 R15: 0000000000000001 FS: 00007f95b9686840(0000) GS:ffff8883af100000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: fffffbfff80a702b CR3: 0000000117dd2000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> proc_lookup_de+0x11f/0x2e0 __lookup_slow+0x188/0x350 walk_component+0x2ab/0x4f0 path_lookupat+0x120/0x660 filename_lookup+0x1ce/0x560 vfs_statx+0xac/0x150 __do_sys_newstat+0x96/0x110 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e [adobriyan@gmail.com: don't do 2 atomic ops on the common path]

• CVE-2025-22005 — CVE-2025-22005 · CWE-401

  In the Linux kernel, the following vulnerability has been resolved: ipv6: Fix memleak of nhc_pcpu_rth_output in fib_check_nh_v6_gw(). fib_check_nh_v6_gw() expects that fib6_nh_init() cleans up everything when it fails. Commit 7dd73168e273 ("ipv6: Always allocate pcpu memory in a fib6_nh") moved fib_nh_common_init() before alloc_percpu_gfp() within fib6_nh_init() but forgot to add cleanup for fib6_nh->nh_common.nhc_pcpu_rth_output in case it fails to allocate fib6_nh->rt6i_pcpu, resulting in memleak. Let's call fib_nh_common_release() and clear nhc_pcpu_rth_output in the error path. Note that we can remove the fib6_nh_release() call in nh_create_ipv6() later in net-next.git.

• CVE-2025-22015 — CVE-2025-22015 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: mm/migrate: fix shmem xarray update during migration A shmem folio can be either in page cache or in swap cache, but not at the same time. Namely, once it is in swap cache, folio->mapping should be NULL, and the folio is no longer in a shmem mapping. In __folio_migrate_mapping(), to determine the number of xarray entries to update, folio_test_swapbacked() is used, but that conflates shmem in page cache case and shmem in swap cache case. It leads to xarray multi-index entry corruption, since it turns a sibling entry to a normal entry during xas_store() (see [1] for a userspace reproduction). Fix it by only using folio_test_swapcache() to determine whether xarray is storing swap cache entries or not to choose the right number of xarray entries to update. [1] https://lore.kernel.org/linux-mm/Z8idPCkaJW1IChjT@casper.infradead.org/ Note: In __split_huge_page(), folio_test_anon() && folio_test_swapcache() is used to get swap_cache address space, but that ignores the shmem folio in swap cache case. It could lead to NULL pointer dereferencing when a in-swap-cache shmem folio is split at __xa_store(), since !folio_test_anon() is true and folio->mapping is NULL. But fortunately, its caller split_huge_page_to_list_to_order() bails out early with EBUSY when folio->mapping is NULL. So no need to take care of it here.

• CVE-2025-22055 — CVE-2025-22055 · CWE-125

  In the Linux kernel, the following vulnerability has been resolved: net: fix geneve_opt length integer overflow struct geneve_opt uses 5 bit length for each single option, which means every vary size option should be smaller than 128 bytes. However, all current related Netlink policies cannot promise this length condition and the attacker can exploit a exact 128-byte size option to *fake* a zero length option and confuse the parsing logic, further achieve heap out-of-bounds read. One example crash log is like below: [ 3.905425] ================================================================== [ 3.905925] BUG: KASAN: slab-out-of-bounds in nla_put+0xa9/0xe0 [ 3.906255] Read of size 124 at addr ffff888005f291cc by task poc/177 [ 3.906646] [ 3.906775] CPU: 0 PID: 177 Comm: poc-oob-read Not tainted 6.1.132 #1 [ 3.907131] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 [ 3.907784] Call Trace: [ 3.907925] <TASK> [ 3.908048] dump_stack_lvl+0x44/0x5c [ 3.908258] print_report+0x184/0x4be [ 3.909151] kasan_report+0xc5/0x100 [ 3.909539] kasan_check_range+0xf3/0x1a0 [ 3.909794] memcpy+0x1f/0x60 [ 3.909968] nla_put+0xa9/0xe0 [ 3.910147] tunnel_key_dump+0x945/0xba0 [ 3.911536] tcf_action_dump_1+0x1c1/0x340 [ 3.912436] tcf_action_dump+0x101/0x180 [ 3.912689] tcf_exts_dump+0x164/0x1e0 [ 3.912905] fw_dump+0x18b/0x2d0 [ 3.913483] tcf_fill_node+0x2ee/0x460 [ 3.914778] tfilter_notify+0xf4/0x180 [ 3.915208] tc_new_tfilter+0xd51/0x10d0 [ 3.918615] rtnetlink_rcv_msg+0x4a2/0x560 [ 3.919118] netlink_rcv_skb+0xcd/0x200 [ 3.919787] netlink_unicast+0x395/0x530 [ 3.921032] netlink_sendmsg+0x3d0/0x6d0 [ 3.921987] __sock_sendmsg+0x99/0xa0 [ 3.922220] __sys_sendto+0x1b7/0x240 [ 3.922682] __x64_sys_sendto+0x72/0x90 [ 3.922906] do_syscall_64+0x5e/0x90 [ 3.923814] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 [ 3.924122] RIP: 0033:0x7e83eab84407 [ 3.924331] Code: 48 89 fa 4c 89 df e8 38 aa 00 00 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 1a 5b c3 0f 1f 84 00 00 00 00 00 48 8b 44 24 10 0f 05 <5b> c3 0f 1f 80 00 00 00 00 83 e2 39 83 faf [ 3.925330] RSP: 002b:00007ffff505e370 EFLAGS: 00000202 ORIG_RAX: 000000000000002c [ 3.925752] RAX: ffffffffffffffda RBX: 00007e83eaafa740 RCX: 00007e83eab84407 [ 3.926173] RDX: 00000000000001a8 RSI: 00007ffff505e3c0 RDI: 0000000000000003 [ 3.926587] RBP: 00007ffff505f460 R08: 00007e83eace1000 R09: 000000000000000c [ 3.926977] R10: 0000000000000000 R11: 0000000000000202 R12: 00007ffff505f3c0 [ 3.927367] R13: 00007ffff505f5c8 R14: 00007e83ead1b000 R15: 00005d4fbbe6dcb8 Fix these issues by enforing correct length condition in related policies.

• CVE-2025-22056 — CVE-2025-22056 · CWE-787

  In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_tunnel: fix geneve_opt type confusion addition When handling multiple NFTA_TUNNEL_KEY_OPTS_GENEVE attributes, the parsing logic should place every geneve_opt structure one by one compactly. Hence, when deciding the next geneve_opt position, the pointer addition should be in units of char *. However, the current implementation erroneously does type conversion before the addition, which will lead to heap out-of-bounds write. [ 6.989857] ================================================================== [ 6.990293] BUG: KASAN: slab-out-of-bounds in nft_tunnel_obj_init+0x977/0xa70 [ 6.990725] Write of size 124 at addr ffff888005f18974 by task poc/178 [ 6.991162] [ 6.991259] CPU: 0 PID: 178 Comm: poc-oob-write Not tainted 6.1.132 #1 [ 6.991655] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 [ 6.992281] Call Trace: [ 6.992423] <TASK> [ 6.992586] dump_stack_lvl+0x44/0x5c [ 6.992801] print_report+0x184/0x4be [ 6.993790] kasan_report+0xc5/0x100 [ 6.994252] kasan_check_range+0xf3/0x1a0 [ 6.994486] memcpy+0x38/0x60 [ 6.994692] nft_tunnel_obj_init+0x977/0xa70 [ 6.995677] nft_obj_init+0x10c/0x1b0 [ 6.995891] nf_tables_newobj+0x585/0x950 [ 6.996922] nfnetlink_rcv_batch+0xdf9/0x1020 [ 6.998997] nfnetlink_rcv+0x1df/0x220 [ 6.999537] netlink_unicast+0x395/0x530 [ 7.000771] netlink_sendmsg+0x3d0/0x6d0 [ 7.001462] __sock_sendmsg+0x99/0xa0 [ 7.001707] ____sys_sendmsg+0x409/0x450 [ 7.002391] ___sys_sendmsg+0xfd/0x170 [ 7.003145] __sys_sendmsg+0xea/0x170 [ 7.004359] do_syscall_64+0x5e/0x90 [ 7.005817] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 [ 7.006127] RIP: 0033:0x7ec756d4e407 [ 7.006339] Code: 48 89 fa 4c 89 df e8 38 aa 00 00 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 1a 5b c3 0f 1f 84 00 00 00 00 00 48 8b 44 24 10 0f 05 <5b> c3 0f 1f 80 00 00 00 00 83 e2 39 83 faf [ 7.007364] RSP: 002b:00007ffed5d46760 EFLAGS: 00000202 ORIG_RAX: 000000000000002e [ 7.007827] RAX: ffffffffffffffda RBX: 00007ec756cc4740 RCX: 00007ec756d4e407 [ 7.008223] RDX: 0000000000000000 RSI: 00007ffed5d467f0 RDI: 0000000000000003 [ 7.008620] RBP: 00007ffed5d468a0 R08: 0000000000000000 R09: 0000000000000000 [ 7.009039] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000 [ 7.009429] R13: 00007ffed5d478b0 R14: 00007ec756ee5000 R15: 00005cbd4e655cb8 Fix this bug with correct pointer addition and conversion in parse and dump code.

• CVE-2025-22060 — CVE-2025-22060 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: mvpp2: Prevent parser TCAM memory corruption Protect the parser TCAM/SRAM memory, and the cached (shadow) SRAM information, from concurrent modifications. Both the TCAM and SRAM tables are indirectly accessed by configuring an index register that selects the row to read or write to. This means that operations must be atomic in order to, e.g., avoid spreading writes across multiple rows. Since the shadow SRAM array is used to find free rows in the hardware table, it must also be protected in order to avoid TOCTOU errors where multiple cores allocate the same row. This issue was detected in a situation where `mvpp2_set_rx_mode()` ran concurrently on two CPUs. In this particular case the MVPP2_PE_MAC_UC_PROMISCUOUS entry was corrupted, causing the classifier unit to drop all incoming unicast - indicated by the `rx_classifier_drops` counter.

• CVE-2025-22083 — CVE-2025-22083 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: vhost-scsi: Fix handling of multiple calls to vhost_scsi_set_endpoint If vhost_scsi_set_endpoint is called multiple times without a vhost_scsi_clear_endpoint between them, we can hit multiple bugs found by Haoran Zhang: 1. Use-after-free when no tpgs are found: This fixes a use after free that occurs when vhost_scsi_set_endpoint is called more than once and calls after the first call do not find any tpgs to add to the vs_tpg. When vhost_scsi_set_endpoint first finds tpgs to add to the vs_tpg array match=true, so we will do: vhost_vq_set_backend(vq, vs_tpg); ... kfree(vs->vs_tpg); vs->vs_tpg = vs_tpg; If vhost_scsi_set_endpoint is called again and no tpgs are found match=false so we skip the vhost_vq_set_backend call leaving the pointer to the vs_tpg we then free via: kfree(vs->vs_tpg); vs->vs_tpg = vs_tpg; If a scsi request is then sent we do: vhost_scsi_handle_vq -> vhost_scsi_get_req -> vhost_vq_get_backend which sees the vs_tpg we just did a kfree on. 2. Tpg dir removal hang: This patch fixes an issue where we cannot remove a LIO/target layer tpg (and structs above it like the target) dir due to the refcount dropping to -1. The problem is that if vhost_scsi_set_endpoint detects a tpg is already in the vs->vs_tpg array or if the tpg has been removed so target_depend_item fails, the undepend goto handler will do target_undepend_item on all tpgs in the vs_tpg array dropping their refcount to 0. At this time vs_tpg contains both the tpgs we have added in the current vhost_scsi_set_endpoint call as well as tpgs we added in previous calls which are also in vs->vs_tpg. Later, when vhost_scsi_clear_endpoint runs it will do target_undepend_item on all the tpgs in the vs->vs_tpg which will drop their refcount to -1. Userspace will then not be able to remove the tpg and will hang when it tries to do rmdir on the tpg dir. 3. Tpg leak: This fixes a bug where we can leak tpgs and cause them to be un-removable because the target name is overwritten when vhost_scsi_set_endpoint is called multiple times but with different target names. The bug occurs if a user has called VHOST_SCSI_SET_ENDPOINT and setup a vhost-scsi device to target/tpg mapping, then calls VHOST_SCSI_SET_ENDPOINT again with a new target name that has tpgs we haven't seen before (target1 has tpg1 but target2 has tpg2). When this happens we don't teardown the old target tpg mapping and just overwrite the target name and the vs->vs_tpg array. Later when we do vhost_scsi_clear_endpoint, we are passed in either target1 or target2's name and we will only match that target's tpgs when we loop over the vs->vs_tpg. We will then return from the function without doing target_undepend_item on the tpgs. Because of all these bugs, it looks like being able to call vhost_scsi_set_endpoint multiple times was never supported. The major user, QEMU, already has checks to prevent this use case. So to fix the issues, this patch prevents vhost_scsi_set_endpoint from being called if it's already successfully added tpgs. To add, remove or change the tpg config or target name, you must do a vhost_scsi_clear_endpoint first.

• CVE-2025-22090 — CVE-2025-22090 · CWE-459

  In the Linux kernel, the following vulnerability has been resolved: x86/mm/pat: Fix VM_PAT handling when fork() fails in copy_page_range() If track_pfn_copy() fails, we already added the dst VMA to the maple tree. As fork() fails, we'll cleanup the maple tree, and stumble over the dst VMA for which we neither performed any reservation nor copied any page tables. Consequently untrack_pfn() will see VM_PAT and try obtaining the PAT information from the page table -- which fails because the page table was not copied. The easiest fix would be to simply clear the VM_PAT flag of the dst VMA if track_pfn_copy() fails. However, the whole thing is about "simply" clearing the VM_PAT flag is shaky as well: if we passed track_pfn_copy() and performed a reservation, but copying the page tables fails, we'll simply clear the VM_PAT flag, not properly undoing the reservation ... which is also wrong. So let's fix it properly: set the VM_PAT flag only if the reservation succeeded (leaving it clear initially), and undo the reservation if anything goes wrong while copying the page tables: clearing the VM_PAT flag after undoing the reservation. Note that any copied page table entries will get zapped when the VMA will get removed later, after copy_page_range() succeeded; as VM_PAT is not set then, we won't try cleaning VM_PAT up once more and untrack_pfn() will be happy. Note that leaving these page tables in place without a reservation is not a problem, as we are aborting fork(); this process will never run. A reproducer can trigger this usually at the first try: https://gitlab.com/davidhildenbrand/scratchspace/-/raw/main/reproducers/pat_fork.c WARNING: CPU: 26 PID: 11650 at arch/x86/mm/pat/memtype.c:983 get_pat_info+0xf6/0x110 Modules linked in: ... CPU: 26 UID: 0 PID: 11650 Comm: repro3 Not tainted 6.12.0-rc5+ #92 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:get_pat_info+0xf6/0x110 ... Call Trace: <TASK> ... untrack_pfn+0x52/0x110 unmap_single_vma+0xa6/0xe0 unmap_vmas+0x105/0x1f0 exit_mmap+0xf6/0x460 __mmput+0x4b/0x120 copy_process+0x1bf6/0x2aa0 kernel_clone+0xab/0x440 __do_sys_clone+0x66/0x90 do_syscall_64+0x95/0x180 Likely this case was missed in: d155df53f310 ("x86/mm/pat: clear VM_PAT if copy_p4d_range failed") ... and instead of undoing the reservation we simply cleared the VM_PAT flag. Keep the documentation of these functions in include/linux/pgtable.h, one place is more than sufficient -- we should clean that up for the other functions like track_pfn_remap/untrack_pfn separately.

• CVE-2025-22095 — CVE-2025-22095 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: PCI: brcmstb: Fix error path after a call to regulator_bulk_get() If the regulator_bulk_get() returns an error and no regulators are created, we need to set their number to zero. If we don't do this and the PCIe link up fails, a call to the regulator_bulk_free() will result in a kernel panic. While at it, print the error value, as we cannot return an error upwards as the kernel will WARN() on an error from add_bus(). [kwilczynski: commit log, use comma in the message to match style with other similar messages]

• CVE-2025-22107 — CVE-2025-22107 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: dsa: sja1105: fix kasan out-of-bounds warning in sja1105_table_delete_entry() There are actually 2 problems: - deleting the last element doesn't require the memmove of elements [i + 1, end) over it. Actually, element i+1 is out of bounds. - The memmove itself should move size - i - 1 elements, because the last element is out of bounds. The out-of-bounds element still remains out of bounds after being accessed, so the problem is only that we touch it, not that it becomes in active use. But I suppose it can lead to issues if the out-of-bounds element is part of an unmapped page.

• CVE-2025-22111 — CVE-2025-22111 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: Remove RTNL dance for SIOCBRADDIF and SIOCBRDELIF. SIOCBRDELIF is passed to dev_ioctl() first and later forwarded to br_ioctl_call(), which causes unnecessary RTNL dance and the splat below [0] under RTNL pressure. Let's say Thread A is trying to detach a device from a bridge and Thread B is trying to remove the bridge. In dev_ioctl(), Thread A bumps the bridge device's refcnt by netdev_hold() and releases RTNL because the following br_ioctl_call() also re-acquires RTNL. In the race window, Thread B could acquire RTNL and try to remove the bridge device. Then, rtnl_unlock() by Thread B will release RTNL and wait for netdev_put() by Thread A. Thread A, however, must hold RTNL after the unlock in dev_ifsioc(), which may take long under RTNL pressure, resulting in the splat by Thread B. Thread A (SIOCBRDELIF) Thread B (SIOCBRDELBR) ---------------------- ---------------------- sock_ioctl sock_ioctl `- sock_do_ioctl `- br_ioctl_call `- dev_ioctl `- br_ioctl_stub |- rtnl_lock | |- dev_ifsioc ' ' |- dev = __dev_get_by_name(...) |- netdev_hold(dev, ...) . / |- rtnl_unlock ------. | | |- br_ioctl_call `---> |- rtnl_lock Race | | `- br_ioctl_stub |- br_del_bridge Window | | | |- dev = __dev_get_by_name(...) | | | May take long | `- br_dev_delete(dev, ...) | | | under RTNL pressure | `- unregister_netdevice_queue(dev, ...) | | | | `- rtnl_unlock \ | |- rtnl_lock <-' `- netdev_run_todo | |- ... `- netdev_run_todo | `- rtnl_unlock |- __rtnl_unlock | |- netdev_wait_allrefs_any |- netdev_put(dev, ...) <----------------' Wait refcnt decrement and log splat below To avoid blocking SIOCBRDELBR unnecessarily, let's not call dev_ioctl() for SIOCBRADDIF and SIOCBRDELIF. In the dev_ioctl() path, we do the following: 1. Copy struct ifreq by get_user_ifreq in sock_do_ioctl() 2. Check CAP_NET_ADMIN in dev_ioctl() 3. Call dev_load() in dev_ioctl() 4. Fetch the master dev from ifr.ifr_name in dev_ifsioc() 3. can be done by request_module() in br_ioctl_call(), so we move 1., 2., and 4. to br_ioctl_stub(). Note that 2. is also checked later in add_del_if(), but it's better performed before RTNL. SIOCBRADDIF and SIOCBRDELIF have been processed in dev_ioctl() since the pre-git era, and there seems to be no specific reason to process them there. [0]: unregister_netdevice: waiting for wpan3 to become free. Usage count = 2 ref_tracker: wpan3@ffff8880662d8608 has 1/1 users at __netdev_tracker_alloc include/linux/netdevice.h:4282 [inline] netdev_hold include/linux/netdevice.h:4311 [inline] dev_ifsioc+0xc6a/0x1160 net/core/dev_ioctl.c:624 dev_ioctl+0x255/0x10c0 net/core/dev_ioctl.c:826 sock_do_ioctl+0x1ca/0x260 net/socket.c:1213 sock_ioctl+0x23a/0x6c0 net/socket.c:1318 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl fs/ioctl.c:892 [inline] __x64_sys_ioctl+0x1a4/0x210 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcb/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

• CVE-2025-22121 — CVE-2025-22121 · CWE-125

  In the Linux kernel, the following vulnerability has been resolved: ext4: fix out-of-bound read in ext4_xattr_inode_dec_ref_all() There's issue as follows: BUG: KASAN: use-after-free in ext4_xattr_inode_dec_ref_all+0x6ff/0x790 Read of size 4 at addr ffff88807b003000 by task syz-executor.0/15172 CPU: 3 PID: 15172 Comm: syz-executor.0 Call Trace: __dump_stack lib/dump_stack.c:82 [inline] dump_stack+0xbe/0xfd lib/dump_stack.c:123 print_address_description.constprop.0+0x1e/0x280 mm/kasan/report.c:400 __kasan_report.cold+0x6c/0x84 mm/kasan/report.c:560 kasan_report+0x3a/0x50 mm/kasan/report.c:585 ext4_xattr_inode_dec_ref_all+0x6ff/0x790 fs/ext4/xattr.c:1137 ext4_xattr_delete_inode+0x4c7/0xda0 fs/ext4/xattr.c:2896 ext4_evict_inode+0xb3b/0x1670 fs/ext4/inode.c:323 evict+0x39f/0x880 fs/inode.c:622 iput_final fs/inode.c:1746 [inline] iput fs/inode.c:1772 [inline] iput+0x525/0x6c0 fs/inode.c:1758 ext4_orphan_cleanup fs/ext4/super.c:3298 [inline] ext4_fill_super+0x8c57/0xba40 fs/ext4/super.c:5300 mount_bdev+0x355/0x410 fs/super.c:1446 legacy_get_tree+0xfe/0x220 fs/fs_context.c:611 vfs_get_tree+0x8d/0x2f0 fs/super.c:1576 do_new_mount fs/namespace.c:2983 [inline] path_mount+0x119a/0x1ad0 fs/namespace.c:3316 do_mount+0xfc/0x110 fs/namespace.c:3329 __do_sys_mount fs/namespace.c:3540 [inline] __se_sys_mount+0x219/0x2e0 fs/namespace.c:3514 do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x67/0xd1 Memory state around the buggy address: ffff88807b002f00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88807b002f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff88807b003000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff88807b003080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88807b003100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Above issue happens as ext4_xattr_delete_inode() isn't check xattr is valid if xattr is in inode. To solve above issue call xattr_check_inode() check if xattr if valid in inode. In fact, we can directly verify in ext4_iget_extra_inode(), so that there is no divergent verification.

• CVE-2025-23136 — CVE-2025-23136 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: thermal: int340x: Add NULL check for adev Not all devices have an ACPI companion fwnode, so adev might be NULL. This is similar to the commit cd2fd6eab480 ("platform/x86: int3472: Check for adev == NULL"). Add a check for adev not being set and return -ENODEV in that case to avoid a possible NULL pointer deref in int3402_thermal_probe(). Note, under the same directory, int3400_thermal_probe() has such a check. [ rjw: Subject edit, added Fixes: ]

• CVE-2025-23143 — CVE-2025-23143 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: net: Fix null-ptr-deref by sock_lock_init_class_and_name() and rmmod. When I ran the repro [0] and waited a few seconds, I observed two LOCKDEP splats: a warning immediately followed by a null-ptr-deref. [1] Reproduction Steps: 1) Mount CIFS 2) Add an iptables rule to drop incoming FIN packets for CIFS 3) Unmount CIFS 4) Unload the CIFS module 5) Remove the iptables rule At step 3), the CIFS module calls sock_release() for the underlying TCP socket, and it returns quickly. However, the socket remains in FIN_WAIT_1 because incoming FIN packets are dropped. At this point, the module's refcnt is 0 while the socket is still alive, so the following rmmod command succeeds. # ss -tan State Recv-Q Send-Q Local Address:Port Peer Address:Port FIN-WAIT-1 0 477 10.0.2.15:51062 10.0.0.137:445 # lsmod | grep cifs cifs 1159168 0 This highlights a discrepancy between the lifetime of the CIFS module and the underlying TCP socket. Even after CIFS calls sock_release() and it returns, the TCP socket does not die immediately in order to close the connection gracefully. While this is generally fine, it causes an issue with LOCKDEP because CIFS assigns a different lock class to the TCP socket's sk->sk_lock using sock_lock_init_class_and_name(). Once an incoming packet is processed for the socket or a timer fires, sk->sk_lock is acquired. Then, LOCKDEP checks the lock context in check_wait_context(), where hlock_class() is called to retrieve the lock class. However, since the module has already been unloaded, hlock_class() logs a warning and returns NULL, triggering the null-ptr-deref. If LOCKDEP is enabled, we must ensure that a module calling sock_lock_init_class_and_name() (CIFS, NFS, etc) cannot be unloaded while such a socket is still alive to prevent this issue. Let's hold the module reference in sock_lock_init_class_and_name() and release it when the socket is freed in sk_prot_free(). Note that sock_lock_init() clears sk->sk_owner for svc_create_socket() that calls sock_lock_init_class_and_name() for a listening socket, which clones a socket by sk_clone_lock() without GFP_ZERO. [0]: CIFS_SERVER="10.0.0.137" CIFS_PATH="//${CIFS_SERVER}/Users/Administrator/Desktop/CIFS_TEST" DEV="enp0s3" CRED="/root/WindowsCredential.txt" MNT=$(mktemp -d /tmp/XXXXXX) mount -t cifs ${CIFS_PATH} ${MNT} -o vers=3.0,credentials=${CRED},cache=none,echo_interval=1 iptables -A INPUT -s ${CIFS_SERVER} -j DROP for i in $(seq 10); do umount ${MNT} rmmod cifs sleep 1 done rm -r ${MNT} iptables -D INPUT -s ${CIFS_SERVER} -j DROP [1]: DEBUG_LOCKS_WARN_ON(1) WARNING: CPU: 10 PID: 0 at kernel/locking/lockdep.c:234 hlock_class (kernel/locking/lockdep.c:234 kernel/locking/lockdep.c:223) Modules linked in: cifs_arc4 nls_ucs2_utils cifs_md4 [last unloaded: cifs] CPU: 10 UID: 0 PID: 0 Comm: swapper/10 Not tainted 6.14.0 #36 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:hlock_class (kernel/locking/lockdep.c:234 kernel/locking/lockdep.c:223) ... Call Trace: <IRQ> __lock_acquire (kernel/locking/lockdep.c:4853 kernel/locking/lockdep.c:5178) lock_acquire (kernel/locking/lockdep.c:469 kernel/locking/lockdep.c:5853 kernel/locking/lockdep.c:5816) _raw_spin_lock_nested (kernel/locking/spinlock.c:379) tcp_v4_rcv (./include/linux/skbuff.h:1678 ./include/net/tcp.h:2547 net/ipv4/tcp_ipv4.c:2350) ... BUG: kernel NULL pointer dereference, address: 00000000000000c4 PF: supervisor read access in kernel mode PF: error_code(0x0000) - not-present page PGD 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 10 UID: 0 PID: 0 Comm: swapper/10 Tainted: G W 6.14.0 #36 Tainted: [W]=WARN Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:__lock_acquire (kernel/ ---truncated---

• CVE-2025-37785 — CVE-2025-37785 · CWE-125

  In the Linux kernel, the following vulnerability has been resolved: ext4: fix OOB read when checking dotdot dir Mounting a corrupted filesystem with directory which contains '.' dir entry with rec_len == block size results in out-of-bounds read (later on, when the corrupted directory is removed). ext4_empty_dir() assumes every ext4 directory contains at least '.' and '..' as directory entries in the first data block. It first loads the '.' dir entry, performs sanity checks by calling ext4_check_dir_entry() and then uses its rec_len member to compute the location of '..' dir entry (in ext4_next_entry). It assumes the '..' dir entry fits into the same data block. If the rec_len of '.' is precisely one block (4KB), it slips through the sanity checks (it is considered the last directory entry in the data block) and leaves "struct ext4_dir_entry_2 *de" point exactly past the memory slot allocated to the data block. The following call to ext4_check_dir_entry() on new value of de then dereferences this pointer which results in out-of-bounds mem access. Fix this by extending __ext4_check_dir_entry() to check for '.' dir entries that reach the end of data block. Make sure to ignore the phony dir entries for checksum (by checking name_len for non-zero). Note: This is reported by KASAN as use-after-free in case another structure was recently freed from the slot past the bound, but it is really an OOB read. This issue was found by syzkaller tool. Call Trace: [ 38.594108] BUG: KASAN: slab-use-after-free in __ext4_check_dir_entry+0x67e/0x710 [ 38.594649] Read of size 2 at addr ffff88802b41a004 by task syz-executor/5375 [ 38.595158] [ 38.595288] CPU: 0 UID: 0 PID: 5375 Comm: syz-executor Not tainted 6.14.0-rc7 #1 [ 38.595298] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 [ 38.595304] Call Trace: [ 38.595308] <TASK> [ 38.595311] dump_stack_lvl+0xa7/0xd0 [ 38.595325] print_address_description.constprop.0+0x2c/0x3f0 [ 38.595339] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595349] print_report+0xaa/0x250 [ 38.595359] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595368] ? kasan_addr_to_slab+0x9/0x90 [ 38.595378] kasan_report+0xab/0xe0 [ 38.595389] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595400] __ext4_check_dir_entry+0x67e/0x710 [ 38.595410] ext4_empty_dir+0x465/0x990 [ 38.595421] ? __pfx_ext4_empty_dir+0x10/0x10 [ 38.595432] ext4_rmdir.part.0+0x29a/0xd10 [ 38.595441] ? __dquot_initialize+0x2a7/0xbf0 [ 38.595455] ? __pfx_ext4_rmdir.part.0+0x10/0x10 [ 38.595464] ? __pfx___dquot_initialize+0x10/0x10 [ 38.595478] ? down_write+0xdb/0x140 [ 38.595487] ? __pfx_down_write+0x10/0x10 [ 38.595497] ext4_rmdir+0xee/0x140 [ 38.595506] vfs_rmdir+0x209/0x670 [ 38.595517] ? lookup_one_qstr_excl+0x3b/0x190 [ 38.595529] do_rmdir+0x363/0x3c0 [ 38.595537] ? __pfx_do_rmdir+0x10/0x10 [ 38.595544] ? strncpy_from_user+0x1ff/0x2e0 [ 38.595561] __x64_sys_unlinkat+0xf0/0x130 [ 38.595570] do_syscall_64+0x5b/0x180 [ 38.595583] entry_SYSCALL_64_after_hwframe+0x76/0x7e

• CVE-2025-37909 — CVE-2025-37909 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: lan743x: Fix memleak issue when GSO enabled Always map the `skb` to the LS descriptor. Previously skb was mapped to EXT descriptor when the number of fragments is zero with GSO enabled. Mapping the skb to EXT descriptor prevents it from being freed, leading to a memory leak

• CVE-2025-37917 — CVE-2025-37917 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk-star-emac: fix spinlock recursion issues on rx/tx poll Use spin_lock_irqsave and spin_unlock_irqrestore instead of spin_lock and spin_unlock in mtk_star_emac driver to avoid spinlock recursion occurrence that can happen when enabling the DMA interrupts again in rx/tx poll. ``` BUG: spinlock recursion on CPU#0, swapper/0/0 lock: 0xffff00000db9cf20, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0 CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.15.0-rc2-next-20250417-00001-gf6a27738686c-dirty #28 PREEMPT Hardware name: MediaTek MT8365 Open Platform EVK (DT) Call trace: show_stack+0x18/0x24 (C) dump_stack_lvl+0x60/0x80 dump_stack+0x18/0x24 spin_dump+0x78/0x88 do_raw_spin_lock+0x11c/0x120 _raw_spin_lock+0x20/0x2c mtk_star_handle_irq+0xc0/0x22c [mtk_star_emac] __handle_irq_event_percpu+0x48/0x140 handle_irq_event+0x4c/0xb0 handle_fasteoi_irq+0xa0/0x1bc handle_irq_desc+0x34/0x58 generic_handle_domain_irq+0x1c/0x28 gic_handle_irq+0x4c/0x120 do_interrupt_handler+0x50/0x84 el1_interrupt+0x34/0x68 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x6c/0x70 regmap_mmio_read32le+0xc/0x20 (P) _regmap_bus_reg_read+0x6c/0xac _regmap_read+0x60/0xdc regmap_read+0x4c/0x80 mtk_star_rx_poll+0x2f4/0x39c [mtk_star_emac] __napi_poll+0x38/0x188 net_rx_action+0x164/0x2c0 handle_softirqs+0x100/0x244 __do_softirq+0x14/0x20 ____do_softirq+0x10/0x20 call_on_irq_stack+0x24/0x64 do_softirq_own_stack+0x1c/0x40 __irq_exit_rcu+0xd4/0x10c irq_exit_rcu+0x10/0x1c el1_interrupt+0x38/0x68 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x6c/0x70 cpuidle_enter_state+0xac/0x320 (P) cpuidle_enter+0x38/0x50 do_idle+0x1e4/0x260 cpu_startup_entry+0x34/0x3c rest_init+0xdc/0xe0 console_on_rootfs+0x0/0x6c __primary_switched+0x88/0x90 ```

• CVE-2025-37945 — CVE-2025-37945 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY DSA has 2 kinds of drivers: 1. Those who call dsa_switch_suspend() and dsa_switch_resume() from their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz 2. Those who don't: all others. The above methods should be optional. For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(), and dsa_switch_resume() calls dsa_user_resume() -> phylink_start(). These seem good candidates for setting mac_managed_pm = true because that is essentially its definition [1], but that does not seem to be the biggest problem for now, and is not what this change focuses on. Talking strictly about the 2nd category of DSA drivers here (which do not have MAC managed PM, meaning that for their attached PHYs, mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full), I have noticed that the following warning from mdio_bus_phy_resume() is triggered: WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY && phydev->state != PHY_UP); because the PHY state machine is running. It's running as a result of a previous dsa_user_open() -> ... -> phylink_start() -> phy_start() having been initiated by the user. The previous mdio_bus_phy_suspend() was supposed to have called phy_stop_machine(), but it didn't. So this is why the PHY is in state PHY_NOLINK by the time mdio_bus_phy_resume() runs. mdio_bus_phy_suspend() did not call phy_stop_machine() because for phylink, the phydev->adjust_link function pointer is NULL. This seems a technicality introduced by commit fddd91016d16 ("phylib: fix PAL state machine restart on resume"). That commit was written before phylink existed, and was intended to avoid crashing with consumer drivers which don't use the PHY state machine - phylink always does, when using a PHY. But phylink itself has historically not been developed with suspend/resume in mind, and apparently not tested too much in that scenario, allowing this bug to exist unnoticed for so long. Plus, prior to the WARN_ON(), it would have likely been invisible. This issue is not in fact restricted to type 2 DSA drivers (according to the above ad-hoc classification), but can be extrapolated to any MAC driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where the issue was reported. Assuming mac_managed_pm is set correctly, a quick search indicates the following other drivers might be affected: $ grep -Zlr PHYLINK_NETDEV drivers/ | xargs -0 grep -L mac_managed_pm drivers/net/ethernet/atheros/ag71xx.c drivers/net/ethernet/microchip/sparx5/sparx5_main.c drivers/net/ethernet/microchip/lan966x/lan966x_main.c drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c drivers/net/ethernet/freescale/dpaa/dpaa_eth.c drivers/net/ethernet/freescale/ucc_geth.c drivers/net/ethernet/freescale/enetc/enetc_pf_common.c drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c drivers/net/ethernet/marvell/mvneta.c drivers/net/ethernet/marvell/prestera/prestera_main.c drivers/net/ethernet/mediatek/mtk_eth_soc.c drivers/net/ethernet/altera/altera_tse_main.c drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c drivers/net/ethernet/meta/fbnic/fbnic_phylink.c drivers/net/ethernet/tehuti/tn40_phy.c drivers/net/ethernet/mscc/ocelot_net.c Make the existing conditions dependent on the PHY device having a phydev->phy_link_change() implementation equal to the default phy_link_change() provided by phylib. Otherwise, we implicitly know that the phydev has the phylink-provided phylink_phy_change() callback, and when phylink is used, the PHY state machine always needs to be stopped/ started on the suspend/resume path. The code is structured as such that if phydev->phy_link_change() is absent, it is a matter of time until the kernel will crash - no need to further complicate the test. Thus, for the situation where the PM is not managed b ---truncated---

• CVE-2025-37959 — CVE-2025-37959 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bpf: Scrub packet on bpf_redirect_peer When bpf_redirect_peer is used to redirect packets to a device in another network namespace, the skb isn't scrubbed. That can lead skb information from one namespace to be "misused" in another namespace. As one example, this is causing Cilium to drop traffic when using bpf_redirect_peer to redirect packets that just went through IPsec decryption to a container namespace. The following pwru trace shows (1) the packet path from the host's XFRM layer to the container's XFRM layer where it's dropped and (2) the number of active skb extensions at each function. NETNS MARK IFACE TUPLE FUNC 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm_rcv_cb .active_extensions = (__u8)2, 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm4_rcv_cb .active_extensions = (__u8)2, 4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 gro_cells_receive .active_extensions = (__u8)2, [...] 4026533547 0 eth0 10.244.3.124:35473->10.244.2.158:53 skb_do_redirect .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv_core .active_extensions = (__u8)2, [...] 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 udp_queue_rcv_one_skb .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_policy_check .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_decode_session .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 security_xfrm_decode_session .active_extensions = (__u8)2, 4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 kfree_skb_reason(SKB_DROP_REASON_XFRM_POLICY) .active_extensions = (__u8)2, In this case, there are no XFRM policies in the container's network namespace so the drop is unexpected. When we decrypt the IPsec packet, the XFRM state used for decryption is set in the skb extensions. This information is preserved across the netns switch. When we reach the XFRM policy check in the container's netns, __xfrm_policy_check drops the packet with LINUX_MIB_XFRMINNOPOLS because a (container-side) XFRM policy can't be found that matches the (host-side) XFRM state used for decryption. This patch fixes this by scrubbing the packet when using bpf_redirect_peer, as is done on typical netns switches via veth devices except skb->mark and skb->tstamp are not zeroed.

• CVE-2025-37964 — CVE-2025-37964 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: x86/mm: Eliminate window where TLB flushes may be inadvertently skipped tl;dr: There is a window in the mm switching code where the new CR3 is set and the CPU should be getting TLB flushes for the new mm. But should_flush_tlb() has a bug and suppresses the flush. Fix it by widening the window where should_flush_tlb() sends an IPI. Long Version: === History === There were a few things leading up to this. First, updating mm_cpumask() was observed to be too expensive, so it was made lazier. But being lazy caused too many unnecessary IPIs to CPUs due to the now-lazy mm_cpumask(). So code was added to cull mm_cpumask() periodically[2]. But that culling was a bit too aggressive and skipped sending TLB flushes to CPUs that need them. So here we are again. === Problem === The too-aggressive code in should_flush_tlb() strikes in this window: // Turn on IPIs for this CPU/mm combination, but only // if should_flush_tlb() agrees: cpumask_set_cpu(cpu, mm_cpumask(next)); next_tlb_gen = atomic64_read(&next->context.tlb_gen); choose_new_asid(next, next_tlb_gen, &new_asid, &need_flush); load_new_mm_cr3(need_flush); // ^ After 'need_flush' is set to false, IPIs *MUST* // be sent to this CPU and not be ignored. this_cpu_write(cpu_tlbstate.loaded_mm, next); // ^ Not until this point does should_flush_tlb() // become true! should_flush_tlb() will suppress TLB flushes between load_new_mm_cr3() and writing to 'loaded_mm', which is a window where they should not be suppressed. Whoops. === Solution === Thankfully, the fuzzy "just about to write CR3" window is already marked with loaded_mm==LOADED_MM_SWITCHING. Simply checking for that state in should_flush_tlb() is sufficient to ensure that the CPU is targeted with an IPI. This will cause more TLB flush IPIs. But the window is relatively small and I do not expect this to cause any kind of measurable performance impact. Update the comment where LOADED_MM_SWITCHING is written since it grew yet another user. Peter Z also raised a concern that should_flush_tlb() might not observe 'loaded_mm' and 'is_lazy' in the same order that switch_mm_irqs_off() writes them. Add a barrier to ensure that they are observed in the order they are written.

• CVE-2025-37972 — CVE-2025-37972 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: Input: mtk-pmic-keys - fix possible null pointer dereference In mtk_pmic_keys_probe, the regs parameter is only set if the button is parsed in the device tree. However, on hardware where the button is left floating, that node will most likely be removed not to enable that input. In that case the code will try to dereference a null pointer. Let's use the regs struct instead as it is defined for all supported platforms. Note that it is ok setting the key reg even if that latter is disabled as the interrupt won't be enabled anyway.

• CVE-2025-37980 — CVE-2025-37980 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: block: fix resource leak in blk_register_queue() error path When registering a queue fails after blk_mq_sysfs_register() is successful but the function later encounters an error, we need to clean up the blk_mq_sysfs resources. Add the missing blk_mq_sysfs_unregister() call in the error path to properly clean up these resources and prevent a memory leak.

• CVE-2025-38125 — CVE-2025-38125 · CWE-369

  In the Linux kernel, the following vulnerability has been resolved: net: stmmac: make sure that ptp_rate is not 0 before configuring EST If the ptp_rate recorded earlier in the driver happens to be 0, this bogus value will propagate up to EST configuration, where it will trigger a division by 0. Prevent this division by 0 by adding the corresponding check and error code.

• CVE-2025-38162 — CVE-2025-38162 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_set_pipapo: prevent overflow in lookup table allocation When calculating the lookup table size, ensure the following multiplication does not overflow: - desc->field_len[] maximum value is U8_MAX multiplied by NFT_PIPAPO_GROUPS_PER_BYTE(f) that can be 2, worst case. - NFT_PIPAPO_BUCKETS(f->bb) is 2^8, worst case. - sizeof(unsigned long), from sizeof(*f->lt), lt in struct nft_pipapo_field. Then, use check_mul_overflow() to multiply by bucket size and then use check_add_overflow() to the alignment for avx2 (if needed). Finally, add lt_size_check_overflow() helper and use it to consolidate this. While at it, replace leftover allocation using the GFP_KERNEL to GFP_KERNEL_ACCOUNT for consistency, in pipapo_resize().

• CVE-2025-38192 — CVE-2025-38192 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: clear the dst when changing skb protocol A not-so-careful NAT46 BPF program can crash the kernel if it indiscriminately flips ingress packets from v4 to v6: BUG: kernel NULL pointer dereference, address: 0000000000000000 ip6_rcv_core (net/ipv6/ip6_input.c:190:20) ipv6_rcv (net/ipv6/ip6_input.c:306:8) process_backlog (net/core/dev.c:6186:4) napi_poll (net/core/dev.c:6906:9) net_rx_action (net/core/dev.c:7028:13) do_softirq (kernel/softirq.c:462:3) netif_rx (net/core/dev.c:5326:3) dev_loopback_xmit (net/core/dev.c:4015:2) ip_mc_finish_output (net/ipv4/ip_output.c:363:8) NF_HOOK (./include/linux/netfilter.h:314:9) ip_mc_output (net/ipv4/ip_output.c:400:5) dst_output (./include/net/dst.h:459:9) ip_local_out (net/ipv4/ip_output.c:130:9) ip_send_skb (net/ipv4/ip_output.c:1496:8) udp_send_skb (net/ipv4/udp.c:1040:8) udp_sendmsg (net/ipv4/udp.c:1328:10) The output interface has a 4->6 program attached at ingress. We try to loop the multicast skb back to the sending socket. Ingress BPF runs as part of netif_rx(), pushes a valid v6 hdr and changes skb->protocol to v6. We enter ip6_rcv_core which tries to use skb_dst(). But the dst is still an IPv4 one left after IPv4 mcast output. Clear the dst in all BPF helpers which change the protocol. Try to preserve metadata dsts, those may carry non-routing metadata.

• CVE-2025-38201 — CVE-2025-38201 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_set_pipapo: clamp maximum map bucket size to INT_MAX Otherwise, it is possible to hit WARN_ON_ONCE in __kvmalloc_node_noprof() when resizing hashtable because __GFP_NOWARN is unset. Similar to: b541ba7d1f5a ("netfilter: conntrack: clamp maximum hashtable size to INT_MAX")

• CVE-2025-38232 — CVE-2025-38232 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: NFSD: fix race between nfsd registration and exports_proc As of now nfsd calls create_proc_exports_entry() at start of init_nfsd and cleanup by remove_proc_entry() at last of exit_nfsd. Which causes kernel OOPs if there is race between below 2 operations: (i) exportfs -r (ii) mount -t nfsd none /proc/fs/nfsd for 5.4 kernel ARM64: CPU 1: el1_irq+0xbc/0x180 arch_counter_get_cntvct+0x14/0x18 running_clock+0xc/0x18 preempt_count_add+0x88/0x110 prep_new_page+0xb0/0x220 get_page_from_freelist+0x2d8/0x1778 __alloc_pages_nodemask+0x15c/0xef0 __vmalloc_node_range+0x28c/0x478 __vmalloc_node_flags_caller+0x8c/0xb0 kvmalloc_node+0x88/0xe0 nfsd_init_net+0x6c/0x108 [nfsd] ops_init+0x44/0x170 register_pernet_operations+0x114/0x270 register_pernet_subsys+0x34/0x50 init_nfsd+0xa8/0x718 [nfsd] do_one_initcall+0x54/0x2e0 CPU 2 : Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010 PC is at : exports_net_open+0x50/0x68 [nfsd] Call trace: exports_net_open+0x50/0x68 [nfsd] exports_proc_open+0x2c/0x38 [nfsd] proc_reg_open+0xb8/0x198 do_dentry_open+0x1c4/0x418 vfs_open+0x38/0x48 path_openat+0x28c/0xf18 do_filp_open+0x70/0xe8 do_sys_open+0x154/0x248 Sometimes it crashes at exports_net_open() and sometimes cache_seq_next_rcu(). and same is happening on latest 6.14 kernel as well: [ 0.000000] Linux version 6.14.0-rc5-next-20250304-dirty ... [ 285.455918] Unable to handle kernel paging request at virtual address 00001f4800001f48 ... [ 285.464902] pc : cache_seq_next_rcu+0x78/0xa4 ... [ 285.469695] Call trace: [ 285.470083] cache_seq_next_rcu+0x78/0xa4 (P) [ 285.470488] seq_read+0xe0/0x11c [ 285.470675] proc_reg_read+0x9c/0xf0 [ 285.470874] vfs_read+0xc4/0x2fc [ 285.471057] ksys_read+0x6c/0xf4 [ 285.471231] __arm64_sys_read+0x1c/0x28 [ 285.471428] invoke_syscall+0x44/0x100 [ 285.471633] el0_svc_common.constprop.0+0x40/0xe0 [ 285.471870] do_el0_svc_compat+0x1c/0x34 [ 285.472073] el0_svc_compat+0x2c/0x80 [ 285.472265] el0t_32_sync_handler+0x90/0x140 [ 285.472473] el0t_32_sync+0x19c/0x1a0 [ 285.472887] Code: f9400885 93407c23 937d7c27 11000421 (f86378a3) [ 285.473422] ---[ end trace 0000000000000000 ]--- It reproduced simply with below script: while [ 1 ] do /exportfs -r done & while [ 1 ] do insmod /nfsd.ko mount -t nfsd none /proc/fs/nfsd umount /proc/fs/nfsd rmmod nfsd done & So exporting interfaces to user space shall be done at last and cleanup at first place. With change there is no Kernel OOPs.

• CVE-2025-38322 — CVE-2025-38322 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel: Fix crash in icl_update_topdown_event() The perf_fuzzer found a hard-lockup crash on a RaptorLake machine: Oops: general protection fault, maybe for address 0xffff89aeceab400: 0000 CPU: 23 UID: 0 PID: 0 Comm: swapper/23 Tainted: [W]=WARN Hardware name: Dell Inc. Precision 9660/0VJ762 RIP: 0010:native_read_pmc+0x7/0x40 Code: cc e8 8d a9 01 00 48 89 03 5b cd cc cc cc cc 0f 1f ... RSP: 000:fffb03100273de8 EFLAGS: 00010046 .... Call Trace: <TASK> icl_update_topdown_event+0x165/0x190 ? ktime_get+0x38/0xd0 intel_pmu_read_event+0xf9/0x210 __perf_event_read+0xf9/0x210 CPUs 16-23 are E-core CPUs that don't support the perf metrics feature. The icl_update_topdown_event() should not be invoked on these CPUs. It's a regression of commit: f9bdf1f95339 ("perf/x86/intel: Avoid disable PMU if !cpuc->enabled in sample read") The bug introduced by that commit is that the is_topdown_event() function is mistakenly used to replace the is_topdown_count() call to check if the topdown functions for the perf metrics feature should be invoked. Fix it.

• CVE-2025-38591 — CVE-2025-38591 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bpf: Reject narrower access to pointer ctx fields The following BPF program, simplified from a syzkaller repro, causes a kernel warning: r0 = *(u8 *)(r1 + 169); exit; With pointer field sk being at offset 168 in __sk_buff. This access is detected as a narrower read in bpf_skb_is_valid_access because it doesn't match offsetof(struct __sk_buff, sk). It is therefore allowed and later proceeds to bpf_convert_ctx_access. Note that for the "is_narrower_load" case in the convert_ctx_accesses(), the insn->off is aligned, so the cnt may not be 0 because it matches the offsetof(struct __sk_buff, sk) in the bpf_convert_ctx_access. However, the target_size stays 0 and the verifier errors with a kernel warning: verifier bug: error during ctx access conversion(1) This patch fixes that to return a proper "invalid bpf_context access off=X size=Y" error on the load instruction. The same issue affects multiple other fields in context structures that allow narrow access. Some other non-affected fields (for sk_msg, sk_lookup, and sockopt) were also changed to use bpf_ctx_range_ptr for consistency. Note this syzkaller crash was reported in the "Closes" link below, which used to be about a different bug, fixed in commit fce7bd8e385a ("bpf/verifier: Handle BPF_LOAD_ACQ instructions in insn_def_regno()"). Because syzbot somehow confused the two bugs, the new crash and repro didn't get reported to the mailing list.

• CVE-2025-38614 — CVE-2025-38614 · CWE-674

  In the Linux kernel, the following vulnerability has been resolved: eventpoll: Fix semi-unbounded recursion Ensure that epoll instances can never form a graph deeper than EP_MAX_NESTS+1 links. Currently, ep_loop_check_proc() ensures that the graph is loop-free and does some recursion depth checks, but those recursion depth checks don't limit the depth of the resulting tree for two reasons: - They don't look upwards in the tree. - If there are multiple downwards paths of different lengths, only one of the paths is actually considered for the depth check since commit 28d82dc1c4ed ("epoll: limit paths"). Essentially, the current recursion depth check in ep_loop_check_proc() just serves to prevent it from recursing too deeply while checking for loops. A more thorough check is done in reverse_path_check() after the new graph edge has already been created; this checks, among other things, that no paths going upwards from any non-epoll file with a length of more than 5 edges exist. However, this check does not apply to non-epoll files. As a result, it is possible to recurse to a depth of at least roughly 500, tested on v6.15. (I am unsure if deeper recursion is possible; and this may have changed with commit 8c44dac8add7 ("eventpoll: Fix priority inversion problem").) To fix it: 1. In ep_loop_check_proc(), note the subtree depth of each visited node, and use subtree depths for the total depth calculation even when a subtree has already been visited. 2. Add ep_get_upwards_depth_proc() for similarly determining the maximum depth of an upwards walk. 3. In ep_loop_check(), use these values to limit the total path length between epoll nodes to EP_MAX_NESTS edges.

• CVE-2025-38681 — CVE-2025-38681 · CWE-366

  In the Linux kernel, the following vulnerability has been resolved: mm/ptdump: take the memory hotplug lock inside ptdump_walk_pgd() Memory hot remove unmaps and tears down various kernel page table regions as required. The ptdump code can race with concurrent modifications of the kernel page tables. When leaf entries are modified concurrently, the dump code may log stale or inconsistent information for a VA range, but this is otherwise not harmful. But when intermediate levels of kernel page table are freed, the dump code will continue to use memory that has been freed and potentially reallocated for another purpose. In such cases, the ptdump code may dereference bogus addresses, leading to a number of potential problems. To avoid the above mentioned race condition, platforms such as arm64, riscv and s390 take memory hotplug lock, while dumping kernel page table via the sysfs interface /sys/kernel/debug/kernel_page_tables. Similar race condition exists while checking for pages that might have been marked W+X via /sys/kernel/debug/kernel_page_tables/check_wx_pages which in turn calls ptdump_check_wx(). Instead of solving this race condition again, let's just move the memory hotplug lock inside generic ptdump_check_wx() which will benefit both the scenarios. Drop get_online_mems() and put_online_mems() combination from all existing platform ptdump code paths.

• CVE-2025-38704 — CVE-2025-38704 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: rcu/nocb: Fix possible invalid rdp's->nocb_cb_kthread pointer access In the preparation stage of CPU online, if the corresponding the rdp's->nocb_cb_kthread does not exist, will be created, there is a situation where the rdp's rcuop kthreads creation fails, and then de-offload this CPU's rdp, does not assign this CPU's rdp->nocb_cb_kthread pointer, but this rdp's->nocb_gp_rdp and rdp's->rdp_gp->nocb_gp_kthread is still valid. This will cause the subsequent re-offload operation of this offline CPU, which will pass the conditional check and the kthread_unpark() will access invalid rdp's->nocb_cb_kthread pointer. This commit therefore use rdp's->nocb_gp_kthread instead of rdp_gp's->nocb_gp_kthread for safety check.

• CVE-2025-38721 — CVE-2025-38721 · CWE-772

  In the Linux kernel, the following vulnerability has been resolved: netfilter: ctnetlink: fix refcount leak on table dump There is a reference count leak in ctnetlink_dump_table(): if (res < 0) { nf_conntrack_get(&ct->ct_general); // HERE cb->args[1] = (unsigned long)ct; ... While its very unlikely, its possible that ct == last. If this happens, then the refcount of ct was already incremented. This 2nd increment is never undone. This prevents the conntrack object from being released, which in turn keeps prevents cnet->count from dropping back to 0. This will then block the netns dismantle (or conntrack rmmod) as nf_conntrack_cleanup_net_list() will wait forever. This can be reproduced by running conntrack_resize.sh selftest in a loop. It takes ~20 minutes for me on a preemptible kernel on average before I see a runaway kworker spinning in nf_conntrack_cleanup_net_list. One fix would to change this to: if (res < 0) { if (ct != last) nf_conntrack_get(&ct->ct_general); But this reference counting isn't needed in the first place. We can just store a cookie value instead. A followup patch will do the same for ctnetlink_exp_dump_table, it looks to me as if this has the same problem and like ctnetlink_dump_table, we only need a 'skip hint', not the actual object so we can apply the same cookie strategy there as well.

• CVE-2025-38725 — CVE-2025-38725 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: usb: asix_devices: add phy_mask for ax88772 mdio bus Without setting phy_mask for ax88772 mdio bus, current driver may create at most 32 mdio phy devices with phy address range from 0x00 ~ 0x1f. DLink DUB-E100 H/W Ver B1 is such a device. However, only one main phy device will bind to net phy driver. This is creating issue during system suspend/resume since phy_polling_mode() in phy_state_machine() will directly deference member of phydev->drv for non-main phy devices. Then NULL pointer dereference issue will occur. Due to only external phy or internal phy is necessary, add phy_mask for ax88772 mdio bus to workarnoud the issue.

• CVE-2025-38727 — CVE-2025-38727 · CWE-835

  In the Linux kernel, the following vulnerability has been resolved: netlink: avoid infinite retry looping in netlink_unicast() netlink_attachskb() checks for the socket's read memory allocation constraints. Firstly, it has: rmem < READ_ONCE(sk->sk_rcvbuf) to check if the just increased rmem value fits into the socket's receive buffer. If not, it proceeds and tries to wait for the memory under: rmem + skb->truesize > READ_ONCE(sk->sk_rcvbuf) The checks don't cover the case when skb->truesize + sk->sk_rmem_alloc is equal to sk->sk_rcvbuf. Thus the function neither successfully accepts these conditions, nor manages to reschedule the task - and is called in retry loop for indefinite time which is caught as: rcu: INFO: rcu_sched self-detected stall on CPU rcu: 0-....: (25999 ticks this GP) idle=ef2/1/0x4000000000000000 softirq=262269/262269 fqs=6212 (t=26000 jiffies g=230833 q=259957) NMI backtrace for cpu 0 CPU: 0 PID: 22 Comm: kauditd Not tainted 5.10.240 #68 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc42 04/01/2014 Call Trace: <IRQ> dump_stack lib/dump_stack.c:120 nmi_cpu_backtrace.cold lib/nmi_backtrace.c:105 nmi_trigger_cpumask_backtrace lib/nmi_backtrace.c:62 rcu_dump_cpu_stacks kernel/rcu/tree_stall.h:335 rcu_sched_clock_irq.cold kernel/rcu/tree.c:2590 update_process_times kernel/time/timer.c:1953 tick_sched_handle kernel/time/tick-sched.c:227 tick_sched_timer kernel/time/tick-sched.c:1399 __hrtimer_run_queues kernel/time/hrtimer.c:1652 hrtimer_interrupt kernel/time/hrtimer.c:1717 __sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1113 asm_call_irq_on_stack arch/x86/entry/entry_64.S:808 </IRQ> netlink_attachskb net/netlink/af_netlink.c:1234 netlink_unicast net/netlink/af_netlink.c:1349 kauditd_send_queue kernel/audit.c:776 kauditd_thread kernel/audit.c:897 kthread kernel/kthread.c:328 ret_from_fork arch/x86/entry/entry_64.S:304 Restore the original behavior of the check which commit in Fixes accidentally missed when restructuring the code. Found by Linux Verification Center (linuxtesting.org).

• CVE-2025-38732 — CVE-2025-38732 · CWE-911

  In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_reject: don't leak dst refcount for loopback packets recent patches to add a WARN() when replacing skb dst entry found an old bug: WARNING: include/linux/skbuff.h:1165 skb_dst_check_unset include/linux/skbuff.h:1164 [inline] WARNING: include/linux/skbuff.h:1165 skb_dst_set include/linux/skbuff.h:1210 [inline] WARNING: include/linux/skbuff.h:1165 nf_reject_fill_skb_dst+0x2a4/0x330 net/ipv4/netfilter/nf_reject_ipv4.c:234 [..] Call Trace: nf_send_unreach+0x17b/0x6e0 net/ipv4/netfilter/nf_reject_ipv4.c:325 nft_reject_inet_eval+0x4bc/0x690 net/netfilter/nft_reject_inet.c:27 expr_call_ops_eval net/netfilter/nf_tables_core.c:237 [inline] .. This is because blamed commit forgot about loopback packets. Such packets already have a dst_entry attached, even at PRE_ROUTING stage. Instead of checking hook just check if the skb already has a route attached to it.

• CVE-2025-38736 — CVE-2025-38736 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: usb: asix_devices: Fix PHY address mask in MDIO bus initialization Syzbot reported shift-out-of-bounds exception on MDIO bus initialization. The PHY address should be masked to 5 bits (0-31). Without this mask, invalid PHY addresses could be used, potentially causing issues with MDIO bus operations. Fix this by masking the PHY address with 0x1f (31 decimal) to ensure it stays within the valid range.

• CVE-2025-39681 — CVE-2025-39681 · CWE-369

  In the Linux kernel, the following vulnerability has been resolved: x86/cpu/hygon: Add missing resctrl_cpu_detect() in bsp_init helper Since 923f3a2b48bd ("x86/resctrl: Query LLC monitoring properties once during boot") resctrl_cpu_detect() has been moved from common CPU initialization code to the vendor-specific BSP init helper, while Hygon didn't put that call in their code. This triggers a division by zero fault during early booting stage on our machines with X86_FEATURE_CQM* supported, where get_rdt_mon_resources() tries to calculate mon_l3_config with uninitialized boot_cpu_data.x86_cache_occ_scale. Add the missing resctrl_cpu_detect() in the Hygon BSP init helper. [ bp: Massage commit message. ]

• CVE-2025-39691 — CVE-2025-39691 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: fs/buffer: fix use-after-free when call bh_read() helper There's issue as follows: BUG: KASAN: stack-out-of-bounds in end_buffer_read_sync+0xe3/0x110 Read of size 8 at addr ffffc9000168f7f8 by task swapper/3/0 CPU: 3 UID: 0 PID: 0 Comm: swapper/3 Not tainted 6.16.0-862.14.0.6.x86_64 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) Call Trace: <IRQ> dump_stack_lvl+0x55/0x70 print_address_description.constprop.0+0x2c/0x390 print_report+0xb4/0x270 kasan_report+0xb8/0xf0 end_buffer_read_sync+0xe3/0x110 end_bio_bh_io_sync+0x56/0x80 blk_update_request+0x30a/0x720 scsi_end_request+0x51/0x2b0 scsi_io_completion+0xe3/0x480 ? scsi_device_unbusy+0x11e/0x160 blk_complete_reqs+0x7b/0x90 handle_softirqs+0xef/0x370 irq_exit_rcu+0xa5/0xd0 sysvec_apic_timer_interrupt+0x6e/0x90 </IRQ> Above issue happens when do ntfs3 filesystem mount, issue may happens as follows: mount IRQ ntfs_fill_super read_cache_page do_read_cache_folio filemap_read_folio mpage_read_folio do_mpage_readpage ntfs_get_block_vbo bh_read submit_bh wait_on_buffer(bh); blk_complete_reqs scsi_io_completion scsi_end_request blk_update_request end_bio_bh_io_sync end_buffer_read_sync __end_buffer_read_notouch unlock_buffer wait_on_buffer(bh);--> return will return to caller put_bh --> trigger stack-out-of-bounds In the mpage_read_folio() function, the stack variable 'map_bh' is passed to ntfs_get_block_vbo(). Once unlock_buffer() unlocks and wait_on_buffer() returns to continue processing, the stack variable is likely to be reclaimed. Consequently, during the end_buffer_read_sync() process, calling put_bh() may result in stack overrun. If the bh is not allocated on the stack, it belongs to a folio. Freeing a buffer head which belongs to a folio is done by drop_buffers() which will fail to free buffers which are still locked. So it is safe to call put_bh() before __end_buffer_read_notouch().

• CVE-2025-39721 — CVE-2025-39721 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: crypto: qat - flush misc workqueue during device shutdown Repeated loading and unloading of a device specific QAT driver, for example qat_4xxx, in a tight loop can lead to a crash due to a use-after-free scenario. This occurs when a power management (PM) interrupt triggers just before the device-specific driver (e.g., qat_4xxx.ko) is unloaded, while the core driver (intel_qat.ko) remains loaded. Since the driver uses a shared workqueue (`qat_misc_wq`) across all devices and owned by intel_qat.ko, a deferred routine from the device-specific driver may still be pending in the queue. If this routine executes after the driver is unloaded, it can dereference freed memory, resulting in a page fault and kernel crash like the following: BUG: unable to handle page fault for address: ffa000002e50a01c #PF: supervisor read access in kernel mode RIP: 0010:pm_bh_handler+0x1d2/0x250 [intel_qat] Call Trace: pm_bh_handler+0x1d2/0x250 [intel_qat] process_one_work+0x171/0x340 worker_thread+0x277/0x3a0 kthread+0xf0/0x120 ret_from_fork+0x2d/0x50 To prevent this, flush the misc workqueue during device shutdown to ensure that all pending work items are completed before the driver is unloaded. Note: This approach may slightly increase shutdown latency if the workqueue contains jobs from other devices, but it ensures correctness and stability.

• CVE-2025-39748 — CVE-2025-39748 · CWE-478

  In the Linux kernel, the following vulnerability has been resolved: bpf: Forget ranges when refining tnum after JSET Syzbot reported a kernel warning due to a range invariant violation on the following BPF program. 0: call bpf_get_netns_cookie 1: if r0 == 0 goto <exit> 2: if r0 & Oxffffffff goto <exit> The issue is on the path where we fall through both jumps. That path is unreachable at runtime: after insn 1, we know r0 != 0, but with the sign extension on the jset, we would only fallthrough insn 2 if r0 == 0. Unfortunately, is_branch_taken() isn't currently able to figure this out, so the verifier walks all branches. The verifier then refines the register bounds using the second condition and we end up with inconsistent bounds on this unreachable path: 1: if r0 == 0 goto <exit> r0: u64=[0x1, 0xffffffffffffffff] var_off=(0, 0xffffffffffffffff) 2: if r0 & 0xffffffff goto <exit> r0 before reg_bounds_sync: u64=[0x1, 0xffffffffffffffff] var_off=(0, 0) r0 after reg_bounds_sync: u64=[0x1, 0] var_off=(0, 0) Improving the range refinement for JSET to cover all cases is tricky. We also don't expect many users to rely on JSET given LLVM doesn't generate those instructions. So instead of improving the range refinement for JSETs, Eduard suggested we forget the ranges whenever we're narrowing tnums after a JSET. This patch implements that approach.

• CVE-2025-39756 — CVE-2025-39756 · CWE-401

  In the Linux kernel, the following vulnerability has been resolved: fs: Prevent file descriptor table allocations exceeding INT_MAX When sysctl_nr_open is set to a very high value (for example, 1073741816 as set by systemd), processes attempting to use file descriptors near the limit can trigger massive memory allocation attempts that exceed INT_MAX, resulting in a WARNING in mm/slub.c: WARNING: CPU: 0 PID: 44 at mm/slub.c:5027 __kvmalloc_node_noprof+0x21a/0x288 This happens because kvmalloc_array() and kvmalloc() check if the requested size exceeds INT_MAX and emit a warning when the allocation is not flagged with __GFP_NOWARN. Specifically, when nr_open is set to 1073741816 (0x3ffffff8) and a process calls dup2(oldfd, 1073741880), the kernel attempts to allocate: - File descriptor array: 1073741880 * 8 bytes = 8,589,935,040 bytes - Multiple bitmaps: ~400MB - Total allocation size: > 8GB (exceeding INT_MAX = 2,147,483,647) Reproducer: 1. Set /proc/sys/fs/nr_open to 1073741816: # echo 1073741816 > /proc/sys/fs/nr_open 2. Run a program that uses a high file descriptor: #include <unistd.h> #include <sys/resource.h> int main() { struct rlimit rlim = {1073741824, 1073741824}; setrlimit(RLIMIT_NOFILE, &rlim); dup2(2, 1073741880); // Triggers the warning return 0; } 3. Observe WARNING in dmesg at mm/slub.c:5027 systemd commit a8b627a introduced automatic bumping of fs.nr_open to the maximum possible value. The rationale was that systems with memory control groups (memcg) no longer need separate file descriptor limits since memory is properly accounted. However, this change overlooked that: 1. The kernel's allocation functions still enforce INT_MAX as a maximum size regardless of memcg accounting 2. Programs and tests that legitimately test file descriptor limits can inadvertently trigger massive allocations 3. The resulting allocations (>8GB) are impractical and will always fail systemd's algorithm starts with INT_MAX and keeps halving the value until the kernel accepts it. On most systems, this results in nr_open being set to 1073741816 (0x3ffffff8), which is just under 1GB of file descriptors. While processes rarely use file descriptors near this limit in normal operation, certain selftests (like tools/testing/selftests/core/unshare_test.c) and programs that test file descriptor limits can trigger this issue. Fix this by adding a check in alloc_fdtable() to ensure the requested allocation size does not exceed INT_MAX. This causes the operation to fail with -EMFILE instead of triggering a kernel warning and avoids the impractical >8GB memory allocation request.

• CVE-2025-39764 — CVE-2025-39764 · CWE-911

  In the Linux kernel, the following vulnerability has been resolved: netfilter: ctnetlink: remove refcounting in expectation dumpers Same pattern as previous patch: do not keep the expectation object alive via refcount, only store a cookie value and then use that as the skip hint for dump resumption. AFAICS this has the same issue as the one resolved in the conntrack dumper, when we do if (!refcount_inc_not_zero(&exp->use)) to increment the refcount, there is a chance that exp == last, which causes a double-increment of the refcount and subsequent memory leak.

• CVE-2025-39770 — CVE-2025-39770 · CWE-573

  In the Linux kernel, the following vulnerability has been resolved: net: gso: Forbid IPv6 TSO with extensions on devices with only IPV6_CSUM When performing Generic Segmentation Offload (GSO) on an IPv6 packet that contains extension headers, the kernel incorrectly requests checksum offload if the egress device only advertises NETIF_F_IPV6_CSUM feature, which has a strict contract: it supports checksum offload only for plain TCP or UDP over IPv6 and explicitly does not support packets with extension headers. The current GSO logic violates this contract by failing to disable the feature for packets with extension headers, such as those used in GREoIPv6 tunnels. This violation results in the device being asked to perform an operation it cannot support, leading to a `skb_warn_bad_offload` warning and a collapse of network throughput. While device TSO/USO is correctly bypassed in favor of software GSO for these packets, the GSO stack must be explicitly told not to request checksum offload. Mask NETIF_F_IPV6_CSUM, NETIF_F_TSO6 and NETIF_F_GSO_UDP_L4 in gso_features_check if the IPv6 header contains extension headers to compute checksum in software. The exception is a BIG TCP extension, which, as stated in commit 68e068cabd2c6c53 ("net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets"): "The feature is only enabled on devices that support BIG TCP TSO. The header is only present for PF_PACKET taps like tcpdump, and not transmitted by physical devices." kernel log output (truncated): WARNING: CPU: 1 PID: 5273 at net/core/dev.c:3535 skb_warn_bad_offload+0x81/0x140 ... Call Trace: <TASK> skb_checksum_help+0x12a/0x1f0 validate_xmit_skb+0x1a3/0x2d0 validate_xmit_skb_list+0x4f/0x80 sch_direct_xmit+0x1a2/0x380 __dev_xmit_skb+0x242/0x670 __dev_queue_xmit+0x3fc/0x7f0 ip6_finish_output2+0x25e/0x5d0 ip6_finish_output+0x1fc/0x3f0 ip6_tnl_xmit+0x608/0xc00 [ip6_tunnel] ip6gre_tunnel_xmit+0x1c0/0x390 [ip6_gre] dev_hard_start_xmit+0x63/0x1c0 __dev_queue_xmit+0x6d0/0x7f0 ip6_finish_output2+0x214/0x5d0 ip6_finish_output+0x1fc/0x3f0 ip6_xmit+0x2ca/0x6f0 ip6_finish_output+0x1fc/0x3f0 ip6_xmit+0x2ca/0x6f0 inet6_csk_xmit+0xeb/0x150 __tcp_transmit_skb+0x555/0xa80 tcp_write_xmit+0x32a/0xe90 tcp_sendmsg_locked+0x437/0x1110 tcp_sendmsg+0x2f/0x50 ... skb linear: 00000000: e4 3d 1a 7d ec 30 e4 3d 1a 7e 5d 90 86 dd 60 0e skb linear: 00000010: 00 0a 1b 34 3c 40 20 11 00 00 00 00 00 00 00 00 skb linear: 00000020: 00 00 00 00 00 12 20 11 00 00 00 00 00 00 00 00 skb linear: 00000030: 00 00 00 00 00 11 2f 00 04 01 04 01 01 00 00 00 skb linear: 00000040: 86 dd 60 0e 00 0a 1b 00 06 40 20 23 00 00 00 00 skb linear: 00000050: 00 00 00 00 00 00 00 00 00 12 20 23 00 00 00 00 skb linear: 00000060: 00 00 00 00 00 00 00 00 00 11 bf 96 14 51 13 f9 skb linear: 00000070: ae 27 a0 a8 2b e3 80 18 00 40 5b 6f 00 00 01 01 skb linear: 00000080: 08 0a 42 d4 50 d5 4b 70 f8 1a

• CVE-2025-39773 — CVE-2025-39773 · CWE-667

  In the Linux kernel, the following vulnerability has been resolved: net: bridge: fix soft lockup in br_multicast_query_expired() When set multicast_query_interval to a large value, the local variable 'time' in br_multicast_send_query() may overflow. If the time is smaller than jiffies, the timer will expire immediately, and then call mod_timer() again, which creates a loop and may trigger the following soft lockup issue. watchdog: BUG: soft lockup - CPU#1 stuck for 221s! [rb_consumer:66] CPU: 1 UID: 0 PID: 66 Comm: rb_consumer Not tainted 6.16.0+ #259 PREEMPT(none) Call Trace: <IRQ> __netdev_alloc_skb+0x2e/0x3a0 br_ip6_multicast_alloc_query+0x212/0x1b70 __br_multicast_send_query+0x376/0xac0 br_multicast_send_query+0x299/0x510 br_multicast_query_expired.constprop.0+0x16d/0x1b0 call_timer_fn+0x3b/0x2a0 __run_timers+0x619/0x950 run_timer_softirq+0x11c/0x220 handle_softirqs+0x18e/0x560 __irq_exit_rcu+0x158/0x1a0 sysvec_apic_timer_interrupt+0x76/0x90 </IRQ> This issue can be reproduced with: ip link add br0 type bridge echo 1 > /sys/class/net/br0/bridge/multicast_querier echo 0xffffffffffffffff > /sys/class/net/br0/bridge/multicast_query_interval ip link set dev br0 up The multicast_startup_query_interval can also cause this issue. Similar to the commit 99b40610956a ("net: bridge: mcast: add and enforce query interval minimum"), add check for the query interval maximum to fix this issue.

• CVE-2025-39782 — CVE-2025-39782 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: jbd2: prevent softlockup in jbd2_log_do_checkpoint() Both jbd2_log_do_checkpoint() and jbd2_journal_shrink_checkpoint_list() periodically release j_list_lock after processing a batch of buffers to avoid long hold times on the j_list_lock. However, since both functions contend for j_list_lock, the combined time spent waiting and processing can be significant. jbd2_journal_shrink_checkpoint_list() explicitly calls cond_resched() when need_resched() is true to avoid softlockups during prolonged operations. But jbd2_log_do_checkpoint() only exits its loop when need_resched() is true, relying on potentially sleeping functions like __flush_batch() or wait_on_buffer() to trigger rescheduling. If those functions do not sleep, the kernel may hit a softlockup. watchdog: BUG: soft lockup - CPU#3 stuck for 156s! [kworker/u129:2:373] CPU: 3 PID: 373 Comm: kworker/u129:2 Kdump: loaded Not tainted 6.6.0+ #10 Hardware name: Huawei TaiShan 2280 /BC11SPCD, BIOS 1.27 06/13/2017 Workqueue: writeback wb_workfn (flush-7:2) pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : native_queued_spin_lock_slowpath+0x358/0x418 lr : jbd2_log_do_checkpoint+0x31c/0x438 [jbd2] Call trace: native_queued_spin_lock_slowpath+0x358/0x418 jbd2_log_do_checkpoint+0x31c/0x438 [jbd2] __jbd2_log_wait_for_space+0xfc/0x2f8 [jbd2] add_transaction_credits+0x3bc/0x418 [jbd2] start_this_handle+0xf8/0x560 [jbd2] jbd2__journal_start+0x118/0x228 [jbd2] __ext4_journal_start_sb+0x110/0x188 [ext4] ext4_do_writepages+0x3dc/0x740 [ext4] ext4_writepages+0xa4/0x190 [ext4] do_writepages+0x94/0x228 __writeback_single_inode+0x48/0x318 writeback_sb_inodes+0x204/0x590 __writeback_inodes_wb+0x54/0xf8 wb_writeback+0x2cc/0x3d8 wb_do_writeback+0x2e0/0x2f8 wb_workfn+0x80/0x2a8 process_one_work+0x178/0x3e8 worker_thread+0x234/0x3b8 kthread+0xf0/0x108 ret_from_fork+0x10/0x20 So explicitly call cond_resched() in jbd2_log_do_checkpoint() to avoid softlockup.

• CVE-2025-39795 — CVE-2025-39795 · CWE-674

  In the Linux kernel, the following vulnerability has been resolved: block: avoid possible overflow for chunk_sectors check in blk_stack_limits() In blk_stack_limits(), we check that the t->chunk_sectors value is a multiple of the t->physical_block_size value. However, by finding the chunk_sectors value in bytes, we may overflow the unsigned int which holds chunk_sectors, so change the check to be based on sectors.

• CVE-2025-39826 — CVE-2025-39826 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: rose: convert 'use' field to refcount_t The 'use' field in struct rose_neigh is used as a reference counter but lacks atomicity. This can lead to race conditions where a rose_neigh structure is freed while still being referenced by other code paths. For example, when rose_neigh->use becomes zero during an ioctl operation via rose_rt_ioctl(), the structure may be removed while its timer is still active, potentially causing use-after-free issues. This patch changes the type of 'use' from unsigned short to refcount_t and updates all code paths to use rose_neigh_hold() and rose_neigh_put() which operate reference counts atomically.

• CVE-2025-39827 — CVE-2025-39827 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: rose: include node references in rose_neigh refcount Current implementation maintains two separate reference counting mechanisms: the 'count' field in struct rose_neigh tracks references from rose_node structures, while the 'use' field (now refcount_t) tracks references from rose_sock. This patch merges these two reference counting systems using 'use' field for proper reference management. Specifically, this patch adds incrementing and decrementing of rose_neigh->use when rose_neigh->count is incremented or decremented. This patch also modifies rose_rt_free(), rose_rt_device_down() and rose_clear_route() to properly release references to rose_neigh objects before freeing a rose_node through rose_remove_node(). These changes ensure rose_neigh structures are properly freed only when all references, including those from rose_node structures, are released. As a result, this resolves a slab-use-after-free issue reported by Syzbot.

• CVE-2025-39845 — CVE-2025-39845 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: x86/mm/64: define ARCH_PAGE_TABLE_SYNC_MASK and arch_sync_kernel_mappings() Define ARCH_PAGE_TABLE_SYNC_MASK and arch_sync_kernel_mappings() to ensure page tables are properly synchronized when calling p*d_populate_kernel(). For 5-level paging, synchronization is performed via pgd_populate_kernel(). In 4-level paging, pgd_populate() is a no-op, so synchronization is instead performed at the P4D level via p4d_populate_kernel(). This fixes intermittent boot failures on systems using 4-level paging and a large amount of persistent memory: BUG: unable to handle page fault for address: ffffe70000000034 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: 0002 [#1] SMP NOPTI RIP: 0010:__init_single_page+0x9/0x6d Call Trace: <TASK> __init_zone_device_page+0x17/0x5d memmap_init_zone_device+0x154/0x1bb pagemap_range+0x2e0/0x40f memremap_pages+0x10b/0x2f0 devm_memremap_pages+0x1e/0x60 dev_dax_probe+0xce/0x2ec [device_dax] dax_bus_probe+0x6d/0xc9 [... snip ...] </TASK> It also fixes a crash in vmemmap_set_pmd() caused by accessing vmemmap before sync_global_pgds() [1]: BUG: unable to handle page fault for address: ffffeb3ff1200000 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 0 P4D 0 Oops: Oops: 0002 [#1] PREEMPT SMP NOPTI Tainted: [W]=WARN RIP: 0010:vmemmap_set_pmd+0xff/0x230 <TASK> vmemmap_populate_hugepages+0x176/0x180 vmemmap_populate+0x34/0x80 __populate_section_memmap+0x41/0x90 sparse_add_section+0x121/0x3e0 __add_pages+0xba/0x150 add_pages+0x1d/0x70 memremap_pages+0x3dc/0x810 devm_memremap_pages+0x1c/0x60 xe_devm_add+0x8b/0x100 [xe] xe_tile_init_noalloc+0x6a/0x70 [xe] xe_device_probe+0x48c/0x740 [xe] [... snip ...]

• CVE-2025-39866 — CVE-2025-39866 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: fs: writeback: fix use-after-free in __mark_inode_dirty() An use-after-free issue occurred when __mark_inode_dirty() get the bdi_writeback that was in the progress of switching. CPU: 1 PID: 562 Comm: systemd-random- Not tainted 6.6.56-gb4403bd46a8e #1 ...... pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __mark_inode_dirty+0x124/0x418 lr : __mark_inode_dirty+0x118/0x418 sp : ffffffc08c9dbbc0 ........ Call trace: __mark_inode_dirty+0x124/0x418 generic_update_time+0x4c/0x60 file_modified+0xcc/0xd0 ext4_buffered_write_iter+0x58/0x124 ext4_file_write_iter+0x54/0x704 vfs_write+0x1c0/0x308 ksys_write+0x74/0x10c __arm64_sys_write+0x1c/0x28 invoke_syscall+0x48/0x114 el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x40/0xe4 el0t_64_sync_handler+0x120/0x12c el0t_64_sync+0x194/0x198 Root cause is: systemd-random-seed kworker ---------------------------------------------------------------------- ___mark_inode_dirty inode_switch_wbs_work_fn spin_lock(&inode->i_lock); inode_attach_wb locked_inode_to_wb_and_lock_list get inode->i_wb spin_unlock(&inode->i_lock); spin_lock(&wb->list_lock) spin_lock(&inode->i_lock) inode_io_list_move_locked spin_unlock(&wb->list_lock) spin_unlock(&inode->i_lock) spin_lock(&old_wb->list_lock) inode_do_switch_wbs spin_lock(&inode->i_lock) inode->i_wb = new_wb spin_unlock(&inode->i_lock) spin_unlock(&old_wb->list_lock) wb_put_many(old_wb, nr_switched) cgwb_release old wb released wb_wakeup_delayed() accesses wb, then trigger the use-after-free issue Fix this race condition by holding inode spinlock until wb_wakeup_delayed() finished.

• CVE-2025-39871 — CVE-2025-39871 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: Remove improper idxd_free The call to idxd_free() introduces a duplicate put_device() leading to a reference count underflow: refcount_t: underflow; use-after-free. WARNING: CPU: 15 PID: 4428 at lib/refcount.c:28 refcount_warn_saturate+0xbe/0x110 ... Call Trace: <TASK> idxd_remove+0xe4/0x120 [idxd] pci_device_remove+0x3f/0xb0 device_release_driver_internal+0x197/0x200 driver_detach+0x48/0x90 bus_remove_driver+0x74/0xf0 pci_unregister_driver+0x2e/0xb0 idxd_exit_module+0x34/0x7a0 [idxd] __do_sys_delete_module.constprop.0+0x183/0x280 do_syscall_64+0x54/0xd70 entry_SYSCALL_64_after_hwframe+0x76/0x7e The idxd_unregister_devices() which is invoked at the very beginning of idxd_remove(), already takes care of the necessary put_device() through the following call path: idxd_unregister_devices() -> device_unregister() -> put_device() In addition, when CONFIG_DEBUG_KOBJECT_RELEASE is enabled, put_device() may trigger asynchronous cleanup via schedule_delayed_work(). If idxd_free() is called immediately after, it can result in a use-after-free. Remove the improper idxd_free() to avoid both the refcount underflow and potential memory corruption during module unload.

• CVE-2025-39931 — CVE-2025-39931 · CWE-457

  In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - Set merge to zero early in af_alg_sendmsg If an error causes af_alg_sendmsg to abort, ctx->merge may contain a garbage value from the previous loop. This may then trigger a crash on the next entry into af_alg_sendmsg when it attempts to do a merge that can't be done. Fix this by setting ctx->merge to zero near the start of the loop.

• CVE-2025-39953 — CVE-2025-39953 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: cgroup: split cgroup_destroy_wq into 3 workqueues A hung task can occur during [1] LTP cgroup testing when repeatedly mounting/unmounting perf_event and net_prio controllers with systemd.unified_cgroup_hierarchy=1. The hang manifests in cgroup_lock_and_drain_offline() during root destruction. Related case: cgroup_fj_function_perf_event cgroup_fj_function.sh perf_event cgroup_fj_function_net_prio cgroup_fj_function.sh net_prio Call Trace: cgroup_lock_and_drain_offline+0x14c/0x1e8 cgroup_destroy_root+0x3c/0x2c0 css_free_rwork_fn+0x248/0x338 process_one_work+0x16c/0x3b8 worker_thread+0x22c/0x3b0 kthread+0xec/0x100 ret_from_fork+0x10/0x20 Root Cause: CPU0 CPU1 mount perf_event umount net_prio cgroup1_get_tree cgroup_kill_sb rebind_subsystems // root destruction enqueues // cgroup_destroy_wq // kill all perf_event css // one perf_event css A is dying // css A offline enqueues cgroup_destroy_wq // root destruction will be executed first css_free_rwork_fn cgroup_destroy_root cgroup_lock_and_drain_offline // some perf descendants are dying // cgroup_destroy_wq max_active = 1 // waiting for css A to die Problem scenario: 1. CPU0 mounts perf_event (rebind_subsystems) 2. CPU1 unmounts net_prio (cgroup_kill_sb), queuing root destruction work 3. A dying perf_event CSS gets queued for offline after root destruction 4. Root destruction waits for offline completion, but offline work is blocked behind root destruction in cgroup_destroy_wq (max_active=1) Solution: Split cgroup_destroy_wq into three dedicated workqueues: cgroup_offline_wq – Handles CSS offline operations cgroup_release_wq – Manages resource release cgroup_free_wq – Performs final memory deallocation This separation eliminates blocking in the CSS free path while waiting for offline operations to complete. [1] https://github.com/linux-test-project/ltp/blob/master/runtest/controllers

• CVE-2025-39955 — CVE-2025-39955 · CWE-213

  In the Linux kernel, the following vulnerability has been resolved: tcp: Clear tcp_sk(sk)->fastopen_rsk in tcp_disconnect(). syzbot reported the splat below where a socket had tcp_sk(sk)->fastopen_rsk in the TCP_ESTABLISHED state. [0] syzbot reused the server-side TCP Fast Open socket as a new client before the TFO socket completes 3WHS: 1. accept() 2. connect(AF_UNSPEC) 3. connect() to another destination As of accept(), sk->sk_state is TCP_SYN_RECV, and tcp_disconnect() changes it to TCP_CLOSE and makes connect() possible, which restarts timers. Since tcp_disconnect() forgot to clear tcp_sk(sk)->fastopen_rsk, the retransmit timer triggered the warning and the intended packet was not retransmitted. Let's call reqsk_fastopen_remove() in tcp_disconnect(). [0]: WARNING: CPU: 2 PID: 0 at net/ipv4/tcp_timer.c:542 tcp_retransmit_timer (net/ipv4/tcp_timer.c:542 (discriminator 7)) Modules linked in: CPU: 2 UID: 0 PID: 0 Comm: swapper/2 Not tainted 6.17.0-rc5-g201825fb4278 #62 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:tcp_retransmit_timer (net/ipv4/tcp_timer.c:542 (discriminator 7)) Code: 41 55 41 54 55 53 48 8b af b8 08 00 00 48 89 fb 48 85 ed 0f 84 55 01 00 00 0f b6 47 12 3c 03 74 0c 0f b6 47 12 3c 04 74 04 90 <0f> 0b 90 48 8b 85 c0 00 00 00 48 89 ef 48 8b 40 30 e8 6a 4f 06 3e RSP: 0018:ffffc900002f8d40 EFLAGS: 00010293 RAX: 0000000000000002 RBX: ffff888106911400 RCX: 0000000000000017 RDX: 0000000002517619 RSI: ffffffff83764080 RDI: ffff888106911400 RBP: ffff888106d5c000 R08: 0000000000000001 R09: ffffc900002f8de8 R10: 00000000000000c2 R11: ffffc900002f8ff8 R12: ffff888106911540 R13: ffff888106911480 R14: ffff888106911840 R15: ffffc900002f8de0 FS: 0000000000000000(0000) GS:ffff88907b768000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8044d69d90 CR3: 0000000002c30003 CR4: 0000000000370ef0 Call Trace: <IRQ> tcp_write_timer (net/ipv4/tcp_timer.c:738) call_timer_fn (kernel/time/timer.c:1747) __run_timers (kernel/time/timer.c:1799 kernel/time/timer.c:2372) timer_expire_remote (kernel/time/timer.c:2385 kernel/time/timer.c:2376 kernel/time/timer.c:2135) tmigr_handle_remote_up (kernel/time/timer_migration.c:944 kernel/time/timer_migration.c:1035) __walk_groups.isra.0 (kernel/time/timer_migration.c:533 (discriminator 1)) tmigr_handle_remote (kernel/time/timer_migration.c:1096) handle_softirqs (./arch/x86/include/asm/jump_label.h:36 ./include/trace/events/irq.h:142 kernel/softirq.c:580) irq_exit_rcu (kernel/softirq.c:614 kernel/softirq.c:453 kernel/softirq.c:680 kernel/softirq.c:696) sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1050 (discriminator 35) arch/x86/kernel/apic/apic.c:1050 (discriminator 35)) </IRQ>

• CVE-2025-39964 — CVE-2025-39964 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - Disallow concurrent writes in af_alg_sendmsg Issuing two writes to the same af_alg socket is bogus as the data will be interleaved in an unpredictable fashion. Furthermore, concurrent writes may create inconsistencies in the internal socket state. Disallow this by adding a new ctx->write field that indiciates exclusive ownership for writing.

• CVE-2025-39977 — CVE-2025-39977 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: futex: Prevent use-after-free during requeue-PI syzbot managed to trigger the following race: T1 T2 futex_wait_requeue_pi() futex_do_wait() schedule() futex_requeue() futex_proxy_trylock_atomic() futex_requeue_pi_prepare() requeue_pi_wake_futex() futex_requeue_pi_complete() /* preempt */ * timeout/ signal wakes T1 * futex_requeue_pi_wakeup_sync() // Q_REQUEUE_PI_LOCKED futex_hash_put() // back to userland, on stack futex_q is garbage /* back */ wake_up_state(q->task, TASK_NORMAL); In this scenario futex_wait_requeue_pi() is able to leave without using futex_q::lock_ptr for synchronization. This can be prevented by reading futex_q::task before updating the futex_q::requeue_state. A reference on the task_struct is not needed because requeue_pi_wake_futex() is invoked with a spinlock_t held which implies a RCU read section. Even if T1 terminates immediately after, the task_struct will remain valid during T2's wake_up_state(). A READ_ONCE on futex_q::task before futex_requeue_pi_complete() is enough because it ensures that the variable is read before the state is updated. Read futex_q::task before updating the requeue state, use it for the following wakeup.

• CVE-2025-39978 — CVE-2025-39978 · CWE-825

  In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: Fix potential use after free in otx2_tc_add_flow() This code calls kfree_rcu(new_node, rcu) and then dereferences "new_node" and then dereferences it on the next line. Two lines later, we take a mutex so I don't think this is an RCU safe region. Re-order it to do the dereferences before queuing up the free.

• CVE-2025-39980 — CVE-2025-39980 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: nexthop: Forbid FDB status change while nexthop is in a group The kernel forbids the creation of non-FDB nexthop groups with FDB nexthops: # ip nexthop add id 1 via 192.0.2.1 fdb # ip nexthop add id 2 group 1 Error: Non FDB nexthop group cannot have fdb nexthops. And vice versa: # ip nexthop add id 3 via 192.0.2.2 dev dummy1 # ip nexthop add id 4 group 3 fdb Error: FDB nexthop group can only have fdb nexthops. However, as long as no routes are pointing to a non-FDB nexthop group, the kernel allows changing the type of a nexthop from FDB to non-FDB and vice versa: # ip nexthop add id 5 via 192.0.2.2 dev dummy1 # ip nexthop add id 6 group 5 # ip nexthop replace id 5 via 192.0.2.2 fdb # echo $? 0 This configuration is invalid and can result in a NPD [1] since FDB nexthops are not associated with a nexthop device: # ip route add 198.51.100.1/32 nhid 6 # ping 198.51.100.1 Fix by preventing nexthop FDB status change while the nexthop is in a group: # ip nexthop add id 7 via 192.0.2.2 dev dummy1 # ip nexthop add id 8 group 7 # ip nexthop replace id 7 via 192.0.2.2 fdb Error: Cannot change nexthop FDB status while in a group. [1] BUG: kernel NULL pointer dereference, address: 00000000000003c0 [...] Oops: Oops: 0000 [#1] SMP CPU: 6 UID: 0 PID: 367 Comm: ping Not tainted 6.17.0-rc6-virtme-gb65678cacc03 #1 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014 RIP: 0010:fib_lookup_good_nhc+0x1e/0x80 [...] Call Trace: <TASK> fib_table_lookup+0x541/0x650 ip_route_output_key_hash_rcu+0x2ea/0x970 ip_route_output_key_hash+0x55/0x80 __ip4_datagram_connect+0x250/0x330 udp_connect+0x2b/0x60 __sys_connect+0x9c/0xd0 __x64_sys_connect+0x18/0x20 do_syscall_64+0xa4/0x2a0 entry_SYSCALL_64_after_hwframe+0x4b/0x53

• CVE-2025-40022 — CVE-2025-40022 · CWE-704

  In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - Fix incorrect boolean values in af_alg_ctx Commit 1b34cbbf4f01 ("crypto: af_alg - Disallow concurrent writes in af_alg_sendmsg") changed some fields from bool to 1-bit bitfields of type u32. However, some assignments to these fields, specifically 'more' and 'merge', assign values greater than 1. These relied on C's implicit conversion to bool, such that zero becomes false and nonzero becomes true. With a 1-bit bitfields of type u32 instead, mod 2 of the value is taken instead, resulting in 0 being assigned in some cases when 1 was intended. Fix this by restoring the bool type.

• CVE-2025-40070 — CVE-2025-40070 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: pps: fix warning in pps_register_cdev when register device fail Similar to previous commit 2a934fdb01db ("media: v4l2-dev: fix error handling in __video_register_device()"), the release hook should be set before device_register(). Otherwise, when device_register() return error and put_device() try to callback the release function, the below warning may happen. ------------[ cut here ]------------ WARNING: CPU: 1 PID: 4760 at drivers/base/core.c:2567 device_release+0x1bd/0x240 drivers/base/core.c:2567 Modules linked in: CPU: 1 UID: 0 PID: 4760 Comm: syz.4.914 Not tainted 6.17.0-rc3+ #1 NONE RIP: 0010:device_release+0x1bd/0x240 drivers/base/core.c:2567 Call Trace: <TASK> kobject_cleanup+0x136/0x410 lib/kobject.c:689 kobject_release lib/kobject.c:720 [inline] kref_put include/linux/kref.h:65 [inline] kobject_put+0xe9/0x130 lib/kobject.c:737 put_device+0x24/0x30 drivers/base/core.c:3797 pps_register_cdev+0x2da/0x370 drivers/pps/pps.c:402 pps_register_source+0x2f6/0x480 drivers/pps/kapi.c:108 pps_tty_open+0x190/0x310 drivers/pps/clients/pps-ldisc.c:57 tty_ldisc_open+0xa7/0x120 drivers/tty/tty_ldisc.c:432 tty_set_ldisc+0x333/0x780 drivers/tty/tty_ldisc.c:563 tiocsetd drivers/tty/tty_io.c:2429 [inline] tty_ioctl+0x5d1/0x1700 drivers/tty/tty_io.c:2728 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:598 [inline] __se_sys_ioctl fs/ioctl.c:584 [inline] __x64_sys_ioctl+0x194/0x210 fs/ioctl.c:584 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x5f/0x2a0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> Before commit c79a39dc8d06 ("pps: Fix a use-after-free"), pps_register_cdev() call device_create() to create pps->dev, which will init dev->release to device_create_release(). Now the comment is outdated, just remove it. Thanks for the reminder from Calvin Owens, 'kfree_pps' should be removed in pps_register_source() to avoid a double free in the failure case.

• CVE-2025-40078 — CVE-2025-40078 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bpf: Explicitly check accesses to bpf_sock_addr Syzkaller found a kernel warning on the following sock_addr program: 0: r0 = 0 1: r2 = *(u32 *)(r1 +60) 2: exit which triggers: verifier bug: error during ctx access conversion (0) This is happening because offset 60 in bpf_sock_addr corresponds to an implicit padding of 4 bytes, right after msg_src_ip4. Access to this padding isn't rejected in sock_addr_is_valid_access and it thus later fails to convert the access. This patch fixes it by explicitly checking the various fields of bpf_sock_addr in sock_addr_is_valid_access. I checked the other ctx structures and is_valid_access functions and didn't find any other similar cases. Other cases of (properly handled) padding are covered in new tests in a subsequent patch.

• CVE-2025-40080 — CVE-2025-40080 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: nbd: restrict sockets to TCP and UDP Recently, syzbot started to abuse NBD with all kinds of sockets. Commit cf1b2326b734 ("nbd: verify socket is supported during setup") made sure the socket supported a shutdown() method. Explicitely accept TCP and UNIX stream sockets.

• CVE-2025-40105 — CVE-2025-40105 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: vfs: Don't leak disconnected dentries on umount When user calls open_by_handle_at() on some inode that is not cached, we will create disconnected dentry for it. If such dentry is a directory, exportfs_decode_fh_raw() will then try to connect this dentry to the dentry tree through reconnect_path(). It may happen for various reasons (such as corrupted fs or race with rename) that the call to lookup_one_unlocked() in reconnect_one() will fail to find the dentry we are trying to reconnect and instead create a new dentry under the parent. Now this dentry will not be marked as disconnected although the parent still may well be disconnected (at least in case this inconsistency happened because the fs is corrupted and .. doesn't point to the real parent directory). This creates inconsistency in disconnected flags but AFAICS it was mostly harmless. At least until commit f1ee616214cb ("VFS: don't keep disconnected dentries on d_anon") which removed adding of most disconnected dentries to sb->s_anon list. Thus after this commit cleanup of disconnected dentries implicitely relies on the fact that dput() will immediately reclaim such dentries. However when some leaf dentry isn't marked as disconnected, as in the scenario described above, the reclaim doesn't happen and the dentries are "leaked". Memory reclaim can eventually reclaim them but otherwise they stay in memory and if umount comes first, we hit infamous "Busy inodes after unmount" bug. Make sure all dentries created under a disconnected parent are marked as disconnected as well.

• CVE-2025-40135 — CVE-2025-40135 · CWE-825

  In the Linux kernel, the following vulnerability has been resolved: ipv6: use RCU in ip6_xmit() Use RCU in ip6_xmit() in order to use dst_dev_rcu() to prevent possible UAF.

• CVE-2025-40149 — CVE-2025-40149 · CWE-416

  In the Linux kernel, the following vulnerability has been resolved: tls: Use __sk_dst_get() and dst_dev_rcu() in get_netdev_for_sock(). get_netdev_for_sock() is called during setsockopt(), so not under RCU. Using sk_dst_get(sk)->dev could trigger UAF. Let's use __sk_dst_get() and dst_dev_rcu(). Note that the only ->ndo_sk_get_lower_dev() user is bond_sk_get_lower_dev(), which uses RCU.

• CVE-2025-40219 — CVE-2025-40219 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: PCI/IOV: Fix race between SR-IOV enable/disable and hotplug Commit 05703271c3cd ("PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV") tried to fix a race between the VF removal inside sriov_del_vfs() and concurrent hot unplug by taking the PCI rescan/remove lock in sriov_del_vfs(). Similarly the PCI rescan/remove lock was also taken in sriov_add_vfs() to protect addition of VFs. This approach however causes deadlock on trying to remove PFs with SR-IOV enabled because PFs disable SR-IOV during removal and this removal happens under the PCI rescan/remove lock. So the original fix had to be reverted. Instead of taking the PCI rescan/remove lock in sriov_add_vfs() and sriov_del_vfs(), fix the race that occurs with SR-IOV enable and disable vs hotplug higher up in the callchain by taking the lock in sriov_numvfs_store() before calling into the driver's sriov_configure() callback.

• CVE-2025-40261 — CVE-2025-40261 · CWE-1341

  In the Linux kernel, the following vulnerability has been resolved: nvme: nvme-fc: Ensure ->ioerr_work is cancelled in nvme_fc_delete_ctrl() nvme_fc_delete_assocation() waits for pending I/O to complete before returning, and an error can cause ->ioerr_work to be queued after cancel_work_sync() had been called. Move the call to cancel_work_sync() to be after nvme_fc_delete_association() to ensure ->ioerr_work is not running when the nvme_fc_ctrl object is freed. Otherwise the following can occur: [ 1135.911754] list_del corruption, ff2d24c8093f31f8->next is NULL [ 1135.917705] ------------[ cut here ]------------ [ 1135.922336] kernel BUG at lib/list_debug.c:52! [ 1135.926784] Oops: invalid opcode: 0000 [#1] SMP NOPTI [ 1135.931851] CPU: 48 UID: 0 PID: 726 Comm: kworker/u449:23 Kdump: loaded Not tainted 6.12.0 #1 PREEMPT(voluntary) [ 1135.943490] Hardware name: Dell Inc. PowerEdge R660/0HGTK9, BIOS 2.5.4 01/16/2025 [ 1135.950969] Workqueue: 0x0 (nvme-wq) [ 1135.954673] RIP: 0010:__list_del_entry_valid_or_report.cold+0xf/0x6f [ 1135.961041] Code: c7 c7 98 68 72 94 e8 26 45 fe ff 0f 0b 48 c7 c7 70 68 72 94 e8 18 45 fe ff 0f 0b 48 89 fe 48 c7 c7 80 69 72 94 e8 07 45 fe ff <0f> 0b 48 89 d1 48 c7 c7 a0 6a 72 94 48 89 c2 e8 f3 44 fe ff 0f 0b [ 1135.979788] RSP: 0018:ff579b19482d3e50 EFLAGS: 00010046 [ 1135.985015] RAX: 0000000000000033 RBX: ff2d24c8093f31f0 RCX: 0000000000000000 [ 1135.992148] RDX: 0000000000000000 RSI: ff2d24d6bfa1d0c0 RDI: ff2d24d6bfa1d0c0 [ 1135.999278] RBP: ff2d24c8093f31f8 R08: 0000000000000000 R09: ffffffff951e2b08 [ 1136.006413] R10: ffffffff95122ac8 R11: 0000000000000003 R12: ff2d24c78697c100 [ 1136.013546] R13: fffffffffffffff8 R14: 0000000000000000 R15: ff2d24c78697c0c0 [ 1136.020677] FS: 0000000000000000(0000) GS:ff2d24d6bfa00000(0000) knlGS:0000000000000000 [ 1136.028765] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1136.034510] CR2: 00007fd207f90b80 CR3: 000000163ea22003 CR4: 0000000000f73ef0 [ 1136.041641] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1136.048776] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 [ 1136.055910] PKRU: 55555554 [ 1136.058623] Call Trace: [ 1136.061074] <TASK> [ 1136.063179] ? show_trace_log_lvl+0x1b0/0x2f0 [ 1136.067540] ? show_trace_log_lvl+0x1b0/0x2f0 [ 1136.071898] ? move_linked_works+0x4a/0xa0 [ 1136.075998] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.081744] ? __die_body.cold+0x8/0x12 [ 1136.085584] ? die+0x2e/0x50 [ 1136.088469] ? do_trap+0xca/0x110 [ 1136.091789] ? do_error_trap+0x65/0x80 [ 1136.095543] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.101289] ? exc_invalid_op+0x50/0x70 [ 1136.105127] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.110874] ? asm_exc_invalid_op+0x1a/0x20 [ 1136.115059] ? __list_del_entry_valid_or_report.cold+0xf/0x6f [ 1136.120806] move_linked_works+0x4a/0xa0 [ 1136.124733] worker_thread+0x216/0x3a0 [ 1136.128485] ? __pfx_worker_thread+0x10/0x10 [ 1136.132758] kthread+0xfa/0x240 [ 1136.135904] ? __pfx_kthread+0x10/0x10 [ 1136.139657] ret_from_fork+0x31/0x50 [ 1136.143236] ? __pfx_kthread+0x10/0x10 [ 1136.146988] ret_from_fork_asm+0x1a/0x30 [ 1136.150915] </TASK>

• CVE-2025-40300 — CVE-2025-40300 · CWE-402

  In the Linux kernel, the following vulnerability has been resolved: x86/vmscape: Add conditional IBPB mitigation VMSCAPE is a vulnerability that exploits insufficient branch predictor isolation between a guest and a userspace hypervisor (like QEMU). Existing mitigations already protect kernel/KVM from a malicious guest. Userspace can additionally be protected by flushing the branch predictors after a VMexit. Since it is the userspace that consumes the poisoned branch predictors, conditionally issue an IBPB after a VMexit and before returning to userspace. Workloads that frequently switch between hypervisor and userspace will incur the most overhead from the new IBPB. This new IBPB is not integrated with the existing IBPB sites. For instance, a task can use the existing speculation control prctl() to get an IBPB at context switch time. With this implementation, the IBPB is doubled up: one at context switch and another before running userspace. The intent is to integrate and optimize these cases post-embargo. [ dhansen: elaborate on suboptimal IBPB solution ]

• CVE-2025-61984 — CVE-2025-61984 · CWE-159

  ssh in OpenSSH before 10.1 allows control characters in usernames that originate from certain possibly untrusted sources, potentially leading to code execution when a ProxyCommand is used. The untrusted sources are the command line and %-sequence expansion of a configuration file. (A configuration file that provides a complete literal username is not categorized as an untrusted source.)

• CVE-2025-61985 — CVE-2025-61985 · CWE-158

  ssh in OpenSSH before 10.1 allows the '\0' character in an ssh:// URI, potentially leading to code execution when a ProxyCommand is used.

• CVE-2025-68206 — CVE-2025-68206 · CWE-166

  In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_ct: add seqadj extension for natted connections Sequence adjustment may be required for FTP traffic with PASV/EPSV modes. due to need to re-write packet payload (IP, port) on the ftp control connection. This can require changes to the TCP length and expected seq / ack_seq. The easiest way to reproduce this issue is with PASV mode. Example ruleset: table inet ftp_nat { ct helper ftp_helper { type "ftp" protocol tcp l3proto inet } chain prerouting { type filter hook prerouting priority 0; policy accept; tcp dport 21 ct state new ct helper set "ftp_helper" } } table ip nat { chain prerouting { type nat hook prerouting priority -100; policy accept; tcp dport 21 dnat ip prefix to ip daddr map { 192.168.100.1 : 192.168.13.2/32 } } chain postrouting { type nat hook postrouting priority 100 ; policy accept; tcp sport 21 snat ip prefix to ip saddr map { 192.168.13.2 : 192.168.100.1/32 } } } Note that the ftp helper gets assigned *after* the dnat setup. The inverse (nat after helper assign) is handled by an existing check in nf_nat_setup_info() and will not show the problem. Topoloy: +-------------------+ +----------------------------------+ | FTP: 192.168.13.2 | <-> | NAT: 192.168.13.3, 192.168.100.1 | +-------------------+ +----------------------------------+ | +-----------------------+ | Client: 192.168.100.2 | +-----------------------+ ftp nat changes do not work as expected in this case: Connected to 192.168.100.1. [..] ftp> epsv EPSV/EPRT on IPv4 off. ftp> ls 227 Entering passive mode (192,168,100,1,209,129). 421 Service not available, remote server has closed connection. Kernel logs: Missing nfct_seqadj_ext_add() setup call WARNING: CPU: 1 PID: 0 at net/netfilter/nf_conntrack_seqadj.c:41 [..] __nf_nat_mangle_tcp_packet+0x100/0x160 [nf_nat] nf_nat_ftp+0x142/0x280 [nf_nat_ftp] help+0x4d1/0x880 [nf_conntrack_ftp] nf_confirm+0x122/0x2e0 [nf_conntrack] nf_hook_slow+0x3c/0xb0 .. Fix this by adding the required extension when a conntrack helper is assigned to a connection that has a nat binding.

• CVE-2025-68261 — CVE-2025-68261 · CWE-367

  In the Linux kernel, the following vulnerability has been resolved: ext4: add i_data_sem protection in ext4_destroy_inline_data_nolock() Fix a race between inline data destruction and block mapping. The function ext4_destroy_inline_data_nolock() changes the inode data layout by clearing EXT4_INODE_INLINE_DATA and setting EXT4_INODE_EXTENTS. At the same time, another thread may execute ext4_map_blocks(), which tests EXT4_INODE_EXTENTS to decide whether to call ext4_ext_map_blocks() or ext4_ind_map_blocks(). Without i_data_sem protection, ext4_ind_map_blocks() may receive inode with EXT4_INODE_EXTENTS flag and triggering assert. kernel BUG at fs/ext4/indirect.c:546! EXT4-fs (loop2): unmounting filesystem. invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014 RIP: 0010:ext4_ind_map_blocks.cold+0x2b/0x5a fs/ext4/indirect.c:546 Call Trace: <TASK> ext4_map_blocks+0xb9b/0x16f0 fs/ext4/inode.c:681 _ext4_get_block+0x242/0x590 fs/ext4/inode.c:822 ext4_block_write_begin+0x48b/0x12c0 fs/ext4/inode.c:1124 ext4_write_begin+0x598/0xef0 fs/ext4/inode.c:1255 ext4_da_write_begin+0x21e/0x9c0 fs/ext4/inode.c:3000 generic_perform_write+0x259/0x5d0 mm/filemap.c:3846 ext4_buffered_write_iter+0x15b/0x470 fs/ext4/file.c:285 ext4_file_write_iter+0x8e0/0x17f0 fs/ext4/file.c:679 call_write_iter include/linux/fs.h:2271 [inline] do_iter_readv_writev+0x212/0x3c0 fs/read_write.c:735 do_iter_write+0x186/0x710 fs/read_write.c:861 vfs_iter_write+0x70/0xa0 fs/read_write.c:902 iter_file_splice_write+0x73b/0xc90 fs/splice.c:685 do_splice_from fs/splice.c:763 [inline] direct_splice_actor+0x10f/0x170 fs/splice.c:950 splice_direct_to_actor+0x33a/0xa10 fs/splice.c:896 do_splice_direct+0x1a9/0x280 fs/splice.c:1002 do_sendfile+0xb13/0x12c0 fs/read_write.c:1255 __do_sys_sendfile64 fs/read_write.c:1323 [inline] __se_sys_sendfile64 fs/read_write.c:1309 [inline] __x64_sys_sendfile64+0x1cf/0x210 fs/read_write.c:1309 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

• CVE-2025-68264 — CVE-2025-68264 · CWE-362

  In the Linux kernel, the following vulnerability has been resolved: ext4: refresh inline data size before write operations The cached ei->i_inline_size can become stale between the initial size check and when ext4_update_inline_data()/ext4_create_inline_data() use it. Although ext4_get_max_inline_size() reads the correct value at the time of the check, concurrent xattr operations can modify i_inline_size before ext4_write_lock_xattr() is acquired. This causes ext4_update_inline_data() and ext4_create_inline_data() to work with stale capacity values, leading to a BUG_ON() crash in ext4_write_inline_data(): kernel BUG at fs/ext4/inline.c:1331! BUG_ON(pos + len > EXT4_I(inode)->i_inline_size); The race window: 1. ext4_get_max_inline_size() reads i_inline_size = 60 (correct) 2. Size check passes for 50-byte write 3. [Another thread adds xattr, i_inline_size changes to 40] 4. ext4_write_lock_xattr() acquires lock 5. ext4_update_inline_data() uses stale i_inline_size = 60 6. Attempts to write 50 bytes but only 40 bytes actually available 7. BUG_ON() triggers Fix this by recalculating i_inline_size via ext4_find_inline_data_nolock() immediately after acquiring xattr_sem. This ensures ext4_update_inline_data() and ext4_create_inline_data() work with current values that are protected from concurrent modifications. This is similar to commit a54c4613dac1 ("ext4: fix race writing to an inline_data file while its xattrs are changing") which fixed i_inline_off staleness. This patch addresses the related i_inline_size staleness issue.

• CVE-2025-68265 — CVE-2025-68265 · CWE-825

  In the Linux kernel, the following vulnerability has been resolved: nvme: fix admin request_queue lifetime The namespaces can access the controller's admin request_queue, and stale references on the namespaces may exist after tearing down the controller. Ensure the admin request_queue is active by moving the controller's 'put' to after all controller references have been released to ensure no one is can access the request_queue. This fixes a reported use-after-free bug: BUG: KASAN: slab-use-after-free in blk_queue_enter+0x41c/0x4a0 Read of size 8 at addr ffff88c0a53819f8 by task nvme/3287 CPU: 67 UID: 0 PID: 3287 Comm: nvme Tainted: G E 6.13.2-ga1582f1a031e #15 Tainted: [E]=UNSIGNED_MODULE Hardware name: Jabil /EGS 2S MB1, BIOS 1.00 06/18/2025 Call Trace: <TASK> dump_stack_lvl+0x4f/0x60 print_report+0xc4/0x620 ? _raw_spin_lock_irqsave+0x70/0xb0 ? _raw_read_unlock_irqrestore+0x30/0x30 ? blk_queue_enter+0x41c/0x4a0 kasan_report+0xab/0xe0 ? blk_queue_enter+0x41c/0x4a0 blk_queue_enter+0x41c/0x4a0 ? __irq_work_queue_local+0x75/0x1d0 ? blk_queue_start_drain+0x70/0x70 ? irq_work_queue+0x18/0x20 ? vprintk_emit.part.0+0x1cc/0x350 ? wake_up_klogd_work_func+0x60/0x60 blk_mq_alloc_request+0x2b7/0x6b0 ? __blk_mq_alloc_requests+0x1060/0x1060 ? __switch_to+0x5b7/0x1060 nvme_submit_user_cmd+0xa9/0x330 nvme_user_cmd.isra.0+0x240/0x3f0 ? force_sigsegv+0xe0/0xe0 ? nvme_user_cmd64+0x400/0x400 ? vfs_fileattr_set+0x9b0/0x9b0 ? cgroup_update_frozen_flag+0x24/0x1c0 ? cgroup_leave_frozen+0x204/0x330 ? nvme_ioctl+0x7c/0x2c0 blkdev_ioctl+0x1a8/0x4d0 ? blkdev_common_ioctl+0x1930/0x1930 ? fdget+0x54/0x380 __x64_sys_ioctl+0x129/0x190 do_syscall_64+0x5b/0x160 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7f765f703b0b Code: ff ff ff 85 c0 79 9b 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d dd 52 0f 00 f7 d8 64 89 01 48 RSP: 002b:00007ffe2cefe808 EFLAGS: 00000202 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffe2cefe860 RCX: 00007f765f703b0b RDX: 00007ffe2cefe860 RSI: 00000000c0484e41 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000000000003 R09: 0000000000000000 R10: 00007f765f611d50 R11: 0000000000000202 R12: 0000000000000003 R13: 00000000c0484e41 R14: 0000000000000001 R15: 00007ffe2cefea60 </TASK>

• CVE-2025-68266 — CVE-2025-68266 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bfs: Reconstruct file type when loading from disk syzbot is reporting that S_IFMT bits of inode->i_mode can become bogus when the S_IFMT bits of the 32bits "mode" field loaded from disk are corrupted or when the 32bits "attributes" field loaded from disk are corrupted. A documentation says that BFS uses only lower 9 bits of the "mode" field. But I can't find an explicit explanation that the unused upper 23 bits (especially, the S_IFMT bits) are initialized with 0. Therefore, ignore the S_IFMT bits of the "mode" field loaded from disk. Also, verify that the value of the "attributes" field loaded from disk is either BFS_VREG or BFS_VDIR (because BFS supports only regular files and the root directory).

• CVE-2025-68291 — CVE-2025-68291 · CWE-909

  In the Linux kernel, the following vulnerability has been resolved: mptcp: Initialise rcv_mss before calling tcp_send_active_reset() in mptcp_do_fastclose(). syzbot reported divide-by-zero in __tcp_select_window() by MPTCP socket. [0] We had a similar issue for the bare TCP and fixed in commit 499350a5a6e7 ("tcp: initialize rcv_mss to TCP_MIN_MSS instead of 0"). Let's apply the same fix to mptcp_do_fastclose(). [0]: Oops: divide error: 0000 [#1] SMP KASAN PTI CPU: 0 UID: 0 PID: 6068 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 RIP: 0010:__tcp_select_window+0x824/0x1320 net/ipv4/tcp_output.c:3336 Code: ff ff ff 44 89 f1 d3 e0 89 c1 f7 d1 41 01 cc 41 21 c4 e9 a9 00 00 00 e8 ca 49 01 f8 e9 9c 00 00 00 e8 c0 49 01 f8 44 89 e0 99 <f7> 7c 24 1c 41 29 d4 48 bb 00 00 00 00 00 fc ff df e9 80 00 00 00 RSP: 0018:ffffc90003017640 EFLAGS: 00010293 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff88807b469e40 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffc90003017730 R08: ffff888033268143 R09: 1ffff1100664d028 R10: dffffc0000000000 R11: ffffed100664d029 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 FS: 000055557faa0500(0000) GS:ffff888126135000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f64a1912ff8 CR3: 0000000072122000 CR4: 00000000003526f0 Call Trace: <TASK> tcp_select_window net/ipv4/tcp_output.c:281 [inline] __tcp_transmit_skb+0xbc7/0x3aa0 net/ipv4/tcp_output.c:1568 tcp_transmit_skb net/ipv4/tcp_output.c:1649 [inline] tcp_send_active_reset+0x2d1/0x5b0 net/ipv4/tcp_output.c:3836 mptcp_do_fastclose+0x27e/0x380 net/mptcp/protocol.c:2793 mptcp_disconnect+0x238/0x710 net/mptcp/protocol.c:3253 mptcp_sendmsg_fastopen+0x2f8/0x580 net/mptcp/protocol.c:1776 mptcp_sendmsg+0x1774/0x1980 net/mptcp/protocol.c:1855 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg+0xe5/0x270 net/socket.c:742 __sys_sendto+0x3bd/0x520 net/socket.c:2244 __do_sys_sendto net/socket.c:2251 [inline] __se_sys_sendto net/socket.c:2247 [inline] __x64_sys_sendto+0xde/0x100 net/socket.c:2247 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0xfa0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f66e998f749 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffff9acedb8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007f66e9be5fa0 RCX: 00007f66e998f749 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 00007ffff9acee10 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000001 R13: 00007f66e9be5fa0 R14: 00007f66e9be5fa0 R15: 0000000000000006 </TASK>

• CVE-2025-68337 — CVE-2025-68337 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: jbd2: avoid bug_on in jbd2_journal_get_create_access() when file system corrupted There's issue when file system corrupted: ------------[ cut here ]------------ kernel BUG at fs/jbd2/transaction.c:1289! Oops: invalid opcode: 0000 [#1] SMP KASAN PTI CPU: 5 UID: 0 PID: 2031 Comm: mkdir Not tainted 6.18.0-rc1-next RIP: 0010:jbd2_journal_get_create_access+0x3b6/0x4d0 RSP: 0018:ffff888117aafa30 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff88811a86b000 RCX: ffffffff89a63534 RDX: 1ffff110200ec602 RSI: 0000000000000004 RDI: ffff888100763010 RBP: ffff888100763000 R08: 0000000000000001 R09: ffff888100763028 R10: 0000000000000003 R11: 0000000000000000 R12: 0000000000000000 R13: ffff88812c432000 R14: ffff88812c608000 R15: ffff888120bfc000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f91d6970c99 CR3: 00000001159c4000 CR4: 00000000000006f0 Call Trace: <TASK> __ext4_journal_get_create_access+0x42/0x170 ext4_getblk+0x319/0x6f0 ext4_bread+0x11/0x100 ext4_append+0x1e6/0x4a0 ext4_init_new_dir+0x145/0x1d0 ext4_mkdir+0x326/0x920 vfs_mkdir+0x45c/0x740 do_mkdirat+0x234/0x2f0 __x64_sys_mkdir+0xd6/0x120 do_syscall_64+0x5f/0xfa0 entry_SYSCALL_64_after_hwframe+0x76/0x7e The above issue occurs with us in errors=continue mode when accompanied by storage failures. There have been many inconsistencies in the file system data. In the case of file system data inconsistency, for example, if the block bitmap of a referenced block is not set, it can lead to the situation where a block being committed is allocated and used again. As a result, the following condition will not be satisfied then trigger BUG_ON. Of course, it is entirely possible to construct a problematic image that can trigger this BUG_ON through specific operations. In fact, I have constructed such an image and easily reproduced this issue. Therefore, J_ASSERT() holds true only under ideal conditions, but it may not necessarily be satisfied in exceptional scenarios. Using J_ASSERT() directly in abnormal situations would cause the system to crash, which is clearly not what we want. So here we directly trigger a JBD abort instead of immediately invoking BUG_ON.

• CVE-2025-68349 — CVE-2025-68349 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: NFSv4/pNFS: Clear NFS_INO_LAYOUTCOMMIT in pnfs_mark_layout_stateid_invalid Fixes a crash when layout is null during this call stack: write_inode -> nfs4_write_inode -> pnfs_layoutcommit_inode pnfs_set_layoutcommit relies on the lseg refcount to keep the layout around. Need to clear NFS_INO_LAYOUTCOMMIT otherwise we might attempt to reference a null layout.

• CVE-2025-68363 — CVE-2025-68363 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bpf: Check skb->transport_header is set in bpf_skb_check_mtu The bpf_skb_check_mtu helper needs to use skb->transport_header when the BPF_MTU_CHK_SEGS flag is used: bpf_skb_check_mtu(skb, ifindex, &mtu_len, 0, BPF_MTU_CHK_SEGS) The transport_header is not always set. There is a WARN_ON_ONCE report when CONFIG_DEBUG_NET is enabled + skb->gso_size is set + bpf_prog_test_run is used: WARNING: CPU: 1 PID: 2216 at ./include/linux/skbuff.h:3071 skb_gso_validate_network_len bpf_skb_check_mtu bpf_prog_3920e25740a41171_tc_chk_segs_flag # A test in the next patch bpf_test_run bpf_prog_test_run_skb For a normal ingress skb (not test_run), skb_reset_transport_header is performed but there is plan to avoid setting it as described in commit 2170a1f09148 ("net: no longer reset transport_header in __netif_receive_skb_core()"). This patch fixes the bpf helper by checking skb_transport_header_was_set(). The check is done just before skb->transport_header is used, to avoid breaking the existing bpf prog. The WARN_ON_ONCE is limited to bpf_prog_test_run, so targeting bpf-next.

• CVE-2025-68371 — CVE-2025-68371 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: scsi: smartpqi: Fix device resources accessed after device removal Correct possible race conditions during device removal. Previously, a scheduled work item to reset a LUN could still execute after the device was removed, leading to use-after-free and other resource access issues. This race condition occurs because the abort handler may schedule a LUN reset concurrently with device removal via sdev_destroy(), leading to use-after-free and improper access to freed resources. - Check in the device reset handler if the device is still present in the controller's SCSI device list before running; if not, the reset is skipped. - Cancel any pending TMF work that has not started in sdev_destroy(). - Ensure device freeing in sdev_destroy() is done while holding the LUN reset mutex to avoid races with ongoing resets.

• CVE-2025-68724 — CVE-2025-68724 · CWE-190

  In the Linux kernel, the following vulnerability has been resolved: crypto: asymmetric_keys - prevent overflow in asymmetric_key_generate_id Use check_add_overflow() to guard against potential integer overflows when adding the binary blob lengths and the size of an asymmetric_key_id structure and return ERR_PTR(-EOVERFLOW) accordingly. This prevents a possible buffer overflow when copying data from potentially malicious X.509 certificate fields that can be arbitrarily large, such as ASN.1 INTEGER serial numbers, issuer names, etc.

• CVE-2025-68725 — CVE-2025-68725 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bpf: Do not let BPF test infra emit invalid GSO types to stack Yinhao et al. reported that their fuzzer tool was able to trigger a skb_warn_bad_offload() from netif_skb_features() -> gso_features_check(). When a BPF program - triggered via BPF test infra - pushes the packet to the loopback device via bpf_clone_redirect() then mentioned offload warning can be seen. GSO-related features are then rightfully disabled. We get into this situation due to convert___skb_to_skb() setting gso_segs and gso_size but not gso_type. Technically, it makes sense that this warning triggers since the GSO properties are malformed due to the gso_type. Potentially, the gso_type could be marked non-trustworthy through setting it at least to SKB_GSO_DODGY without any other specific assumptions, but that also feels wrong given we should not go further into the GSO engine in the first place. The checks were added in 121d57af308d ("gso: validate gso_type in GSO handlers") because there were malicious (syzbot) senders that combine a protocol with a non-matching gso_type. If we would want to drop such packets, gso_features_check() currently only returns feature flags via netif_skb_features(), so one location for potentially dropping such skbs could be validate_xmit_unreadable_skb(), but then otoh it would be an additional check in the fast-path for a very corner case. Given bpf_clone_redirect() is the only place where BPF test infra could emit such packets, lets reject them right there.

• CVE-2025-68742 — CVE-2025-68742 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: bpf: Fix invalid prog->stats access when update_effective_progs fails Syzkaller triggers an invalid memory access issue following fault injection in update_effective_progs. The issue can be described as follows: __cgroup_bpf_detach update_effective_progs compute_effective_progs bpf_prog_array_alloc <-- fault inject purge_effective_progs /* change to dummy_bpf_prog */ array->items[index] = &dummy_bpf_prog.prog ---softirq start--- __do_softirq ... __cgroup_bpf_run_filter_skb __bpf_prog_run_save_cb bpf_prog_run stats = this_cpu_ptr(prog->stats) /* invalid memory access */ flags = u64_stats_update_begin_irqsave(&stats->syncp) ---softirq end--- static_branch_dec(&cgroup_bpf_enabled_key[atype]) The reason is that fault injection caused update_effective_progs to fail and then changed the original prog into dummy_bpf_prog.prog in purge_effective_progs. Then a softirq came, and accessing the members of dummy_bpf_prog.prog in the softirq triggers invalid mem access. To fix it, skip updating stats when stats is NULL.

• CVE-2025-68764 — CVE-2025-68764 · CWE-266

  In the Linux kernel, the following vulnerability has been resolved: NFS: Automounted filesystems should inherit ro,noexec,nodev,sync flags When a filesystem is being automounted, it needs to preserve the user-set superblock mount options, such as the "ro" flag.

• CVE-2025-68773 — CVE-2025-68773 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: spi: fsl-cpm: Check length parity before switching to 16 bit mode Commit fc96ec826bce ("spi: fsl-cpm: Use 16 bit mode for large transfers with even size") failed to make sure that the size is really even before switching to 16 bit mode. Until recently the problem went unnoticed because kernfs uses a pre-allocated bounce buffer of size PAGE_SIZE for reading EEPROM. But commit 8ad6249c51d0 ("eeprom: at25: convert to spi-mem API") introduced an additional dynamically allocated bounce buffer whose size is exactly the size of the transfer, leading to a buffer overrun in the fsl-cpm driver when that size is odd. Add the missing length parity verification and remain in 8 bit mode when the length is not even.

• CVE-2025-68776 — CVE-2025-68776 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: net/hsr: fix NULL pointer dereference in prp_get_untagged_frame() prp_get_untagged_frame() calls __pskb_copy() to create frame->skb_std but doesn't check if the allocation failed. If __pskb_copy() returns NULL, skb_clone() is called with a NULL pointer, causing a crash: Oops: general protection fault, probably for non-canonical address 0xdffffc000000000f: 0000 [#1] SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000078-0x000000000000007f] CPU: 0 UID: 0 PID: 5625 Comm: syz.1.18 Not tainted syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:skb_clone+0xd7/0x3a0 net/core/skbuff.c:2041 Code: 03 42 80 3c 20 00 74 08 4c 89 f7 e8 23 29 05 f9 49 83 3e 00 0f 85 a0 01 00 00 e8 94 dd 9d f8 48 8d 6b 7e 49 89 ee 49 c1 ee 03 <43> 0f b6 04 26 84 c0 0f 85 d1 01 00 00 44 0f b6 7d 00 41 83 e7 0c RSP: 0018:ffffc9000d00f200 EFLAGS: 00010207 RAX: ffffffff892235a1 RBX: 0000000000000000 RCX: ffff88803372a480 RDX: 0000000000000000 RSI: 0000000000000820 RDI: 0000000000000000 RBP: 000000000000007e R08: ffffffff8f7d0f77 R09: 1ffffffff1efa1ee R10: dffffc0000000000 R11: fffffbfff1efa1ef R12: dffffc0000000000 R13: 0000000000000820 R14: 000000000000000f R15: ffff88805144cc00 FS: 0000555557f6d500(0000) GS:ffff88808d72f000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000555581d35808 CR3: 000000005040e000 CR4: 0000000000352ef0 Call Trace: <TASK> hsr_forward_do net/hsr/hsr_forward.c:-1 [inline] hsr_forward_skb+0x1013/0x2860 net/hsr/hsr_forward.c:741 hsr_handle_frame+0x6ce/0xa70 net/hsr/hsr_slave.c:84 __netif_receive_skb_core+0x10b9/0x4380 net/core/dev.c:5966 __netif_receive_skb_one_core net/core/dev.c:6077 [inline] __netif_receive_skb+0x72/0x380 net/core/dev.c:6192 netif_receive_skb_internal net/core/dev.c:6278 [inline] netif_receive_skb+0x1cb/0x790 net/core/dev.c:6337 tun_rx_batched+0x1b9/0x730 drivers/net/tun.c:1485 tun_get_user+0x2b65/0x3e90 drivers/net/tun.c:1953 tun_chr_write_iter+0x113/0x200 drivers/net/tun.c:1999 new_sync_write fs/read_write.c:593 [inline] vfs_write+0x5c9/0xb30 fs/read_write.c:686 ksys_write+0x145/0x250 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0xfa0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f0449f8e1ff Code: 89 54 24 18 48 89 74 24 10 89 7c 24 08 e8 f9 92 02 00 48 8b 54 24 18 48 8b 74 24 10 41 89 c0 8b 7c 24 08 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 31 44 89 c7 48 89 44 24 08 e8 4c 93 02 00 48 RSP: 002b:00007ffd7ad94c90 EFLAGS: 00000293 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 00007f044a1e5fa0 RCX: 00007f0449f8e1ff RDX: 000000000000003e RSI: 0000200000000500 RDI: 00000000000000c8 RBP: 00007ffd7ad94d20 R08: 0000000000000000 R09: 0000000000000000 R10: 000000000000003e R11: 0000000000000293 R12: 0000000000000001 R13: 00007f044a1e5fa0 R14: 00007f044a1e5fa0 R15: 0000000000000003 </TASK> Add a NULL check immediately after __pskb_copy() to handle allocation failures gracefully.

• CVE-2025-68782 — CVE-2025-68782 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: scsi: target: Reset t_task_cdb pointer in error case If allocation of cmd->t_task_cdb fails, it remains NULL but is later dereferenced in the 'err' path. In case of error, reset NULL t_task_cdb value to point at the default fixed-size buffer. Found by Linux Verification Center (linuxtesting.org) with SVACE.

• CVE-2025-68787 — CVE-2025-68787 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: netrom: Fix memory leak in nr_sendmsg() syzbot reported a memory leak [1]. When function sock_alloc_send_skb() return NULL in nr_output(), the original skb is not freed, which was allocated in nr_sendmsg(). Fix this by freeing it before return. [1] BUG: memory leak unreferenced object 0xffff888129f35500 (size 240): comm "syz.0.17", pid 6119, jiffies 4294944652 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 10 52 28 81 88 ff ff ..........R(.... backtrace (crc 1456a3e4): kmemleak_alloc_recursive include/linux/kmemleak.h:44 [inline] slab_post_alloc_hook mm/slub.c:4983 [inline] slab_alloc_node mm/slub.c:5288 [inline] kmem_cache_alloc_node_noprof+0x36f/0x5e0 mm/slub.c:5340 __alloc_skb+0x203/0x240 net/core/skbuff.c:660 alloc_skb include/linux/skbuff.h:1383 [inline] alloc_skb_with_frags+0x69/0x3f0 net/core/skbuff.c:6671 sock_alloc_send_pskb+0x379/0x3e0 net/core/sock.c:2965 sock_alloc_send_skb include/net/sock.h:1859 [inline] nr_sendmsg+0x287/0x450 net/netrom/af_netrom.c:1105 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg net/socket.c:742 [inline] sock_write_iter+0x293/0x2a0 net/socket.c:1195 new_sync_write fs/read_write.c:593 [inline] vfs_write+0x45d/0x710 fs/read_write.c:686 ksys_write+0x143/0x170 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xa4/0xfa0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f

• CVE-2025-68788 — CVE-2025-68788 · CWE-360

  In the Linux kernel, the following vulnerability has been resolved: fsnotify: do not generate ACCESS/MODIFY events on child for special files inotify/fanotify do not allow users with no read access to a file to subscribe to events (e.g. IN_ACCESS/IN_MODIFY), but they do allow the same user to subscribe for watching events on children when the user has access to the parent directory (e.g. /dev). Users with no read access to a file but with read access to its parent directory can still stat the file and see if it was accessed/modified via atime/mtime change. The same is not true for special files (e.g. /dev/null). Users will not generally observe atime/mtime changes when other users read/write to special files, only when someone sets atime/mtime via utimensat(). Align fsnotify events with this stat behavior and do not generate ACCESS/MODIFY events to parent watchers on read/write of special files. The events are still generated to parent watchers on utimensat(). This closes some side-channels that could be possibly used for information exfiltration [1]. [1] https://snee.la/pdf/pubs/file-notification-attacks.pdf

• CVE-2025-68798 — CVE-2025-68798 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: perf/x86/amd: Check event before enable to avoid GPF On AMD machines cpuc->events[idx] can become NULL in a subtle race condition with NMI->throttle->x86_pmu_stop(). Check event for NULL in amd_pmu_enable_all() before enable to avoid a GPF. This appears to be an AMD only issue. Syzkaller reported a GPF in amd_pmu_enable_all. INFO: NMI handler (perf_event_nmi_handler) took too long to run: 13.143 msecs Oops: general protection fault, probably for non-canonical address 0xdffffc0000000034: 0000 PREEMPT SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x00000000000001a0-0x00000000000001a7] CPU: 0 UID: 0 PID: 328415 Comm: repro_36674776 Not tainted 6.12.0-rc1-syzk RIP: 0010:x86_pmu_enable_event (arch/x86/events/perf_event.h:1195 arch/x86/events/core.c:1430) RSP: 0018:ffff888118009d60 EFLAGS: 00010012 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000034 RSI: 0000000000000000 RDI: 00000000000001a0 RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000002 R13: ffff88811802a440 R14: ffff88811802a240 R15: ffff8881132d8601 FS: 00007f097dfaa700(0000) GS:ffff888118000000(0000) GS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000200001c0 CR3: 0000000103d56000 CR4: 00000000000006f0 Call Trace: <IRQ> amd_pmu_enable_all (arch/x86/events/amd/core.c:760 (discriminator 2)) x86_pmu_enable (arch/x86/events/core.c:1360) event_sched_out (kernel/events/core.c:1191 kernel/events/core.c:1186 kernel/events/core.c:2346) __perf_remove_from_context (kernel/events/core.c:2435) event_function (kernel/events/core.c:259) remote_function (kernel/events/core.c:92 (discriminator 1) kernel/events/core.c:72 (discriminator 1)) __flush_smp_call_function_queue (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/csd.h:64 kernel/smp.c:135 kernel/smp.c:540) __sysvec_call_function_single (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./arch/x86/include/asm/trace/irq_vectors.h:99 arch/x86/kernel/smp.c:272) sysvec_call_function_single (arch/x86/kernel/smp.c:266 (discriminator 47) arch/x86/kernel/smp.c:266 (discriminator 47)) </IRQ>

• CVE-2025-68803 — CVE-2025-68803 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: NFSD: NFSv4 file creation neglects setting ACL An NFSv4 client that sets an ACL with a named principal during file creation retrieves the ACL afterwards, and finds that it is only a default ACL (based on the mode bits) and not the ACL that was requested during file creation. This violates RFC 8881 section 6.4.1.3: "the ACL attribute is set as given". The issue occurs in nfsd_create_setattr(), which calls nfsd_attrs_valid() to determine whether to call nfsd_setattr(). However, nfsd_attrs_valid() checks only for iattr changes and security labels, but not POSIX ACLs. When only an ACL is present, the function returns false, nfsd_setattr() is skipped, and the POSIX ACL is never applied to the inode. Subsequently, when the client retrieves the ACL, the server finds no POSIX ACL on the inode and returns one generated from the file's mode bits rather than returning the originally-specified ACL.

• CVE-2025-68814 — CVE-2025-68814 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: io_uring: fix filename leak in __io_openat_prep() __io_openat_prep() allocates a struct filename using getname(). However, for the condition of the file being installed in the fixed file table as well as having O_CLOEXEC flag set, the function returns early. At that point, the request doesn't have REQ_F_NEED_CLEANUP flag set. Due to this, the memory for the newly allocated struct filename is not cleaned up, causing a memory leak. Fix this by setting the REQ_F_NEED_CLEANUP for the request just after the successful getname() call, so that when the request is torn down, the filename will be cleaned up, along with other resources needing cleanup.

• CVE-2025-68816 — CVE-2025-68816 · CWE-134

  In the Linux kernel, the following vulnerability has been resolved: net/mlx5: fw_tracer, Validate format string parameters Add validation for format string parameters in the firmware tracer to prevent potential security vulnerabilities and crashes from malformed format strings received from firmware. The firmware tracer receives format strings from the device firmware and uses them to format trace messages. Without proper validation, bad firmware could provide format strings with invalid format specifiers (e.g., %s, %p, %n) that could lead to crashes, or other undefined behavior. Add mlx5_tracer_validate_params() to validate that all format specifiers in trace strings are limited to safe integer/hex formats (%x, %d, %i, %u, %llx, %lx, etc.). Reject strings containing other format types that could be used to access arbitrary memory or cause crashes. Invalid format strings are added to the trace output for visibility with "BAD_FORMAT: " prefix.

• CVE-2025-68818 — CVE-2025-68818 · CWE-476

  In the Linux kernel, the following vulnerability has been resolved: scsi: Revert "scsi: qla2xxx: Perform lockless command completion in abort path" This reverts commit 0367076b0817d5c75dfb83001ce7ce5c64d803a9. The commit being reverted added code to __qla2x00_abort_all_cmds() to call sp->done() without holding a spinlock. But unlike the older code below it, this new code failed to check sp->cmd_type and just assumed TYPE_SRB, which results in a jump to an invalid pointer in target-mode with TYPE_TGT_CMD: qla2xxx [0000:65:00.0]-d034:8: qla24xx_do_nack_work create sess success 0000000009f7a79b qla2xxx [0000:65:00.0]-5003:8: ISP System Error - mbx1=1ff5h mbx2=10h mbx3=0h mbx4=0h mbx5=191h mbx6=0h mbx7=0h. qla2xxx [0000:65:00.0]-d01e:8: -> fwdump no buffer qla2xxx [0000:65:00.0]-f03a:8: qla_target(0): System error async event 0x8002 occurred qla2xxx [0000:65:00.0]-00af:8: Performing ISP error recovery - ha=0000000058183fda. BUG: kernel NULL pointer dereference, address: 0000000000000000 PF: supervisor instruction fetch in kernel mode PF: error_code(0x0010) - not-present page PGD 0 P4D 0 Oops: 0010 [#1] SMP CPU: 2 PID: 9446 Comm: qla2xxx_8_dpc Tainted: G O 6.1.133 #1 Hardware name: Supermicro Super Server/X11SPL-F, BIOS 4.2 12/15/2023 RIP: 0010:0x0 Code: Unable to access opcode bytes at 0xffffffffffffffd6. RSP: 0018:ffffc90001f93dc8 EFLAGS: 00010206 RAX: 0000000000000282 RBX: 0000000000000355 RCX: ffff88810d16a000 RDX: ffff88810dbadaa8 RSI: 0000000000080000 RDI: ffff888169dc38c0 RBP: ffff888169dc38c0 R08: 0000000000000001 R09: 0000000000000045 R10: ffffffffa034bdf0 R11: 0000000000000000 R12: ffff88810800bb40 R13: 0000000000001aa8 R14: ffff888100136610 R15: ffff8881070f7400 FS: 0000000000000000(0000) GS:ffff88bf80080000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 000000010c8ff006 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __die+0x4d/0x8b ? page_fault_oops+0x91/0x180 ? trace_buffer_unlock_commit_regs+0x38/0x1a0 ? exc_page_fault+0x391/0x5e0 ? asm_exc_page_fault+0x22/0x30 __qla2x00_abort_all_cmds+0xcb/0x3e0 [qla2xxx_scst] qla2x00_abort_all_cmds+0x50/0x70 [qla2xxx_scst] qla2x00_abort_isp_cleanup+0x3b7/0x4b0 [qla2xxx_scst] qla2x00_abort_isp+0xfd/0x860 [qla2xxx_scst] qla2x00_do_dpc+0x581/0xa40 [qla2xxx_scst] kthread+0xa8/0xd0 </TASK> Then commit 4475afa2646d ("scsi: qla2xxx: Complete command early within lock") added the spinlock back, because not having the lock caused a race and a crash. But qla2x00_abort_srb() in the switch below already checks for qla2x00_chip_is_down() and handles it the same way, so the code above the switch is now redundant and still buggy in target-mode. Remove it.

• CVE-2025-68820 — CVE-2025-68820 · CWE-252

  In the Linux kernel, the following vulnerability has been resolved: ext4: xattr: fix null pointer deref in ext4_raw_inode() If ext4_get_inode_loc() fails (e.g. if it returns -EFSCORRUPTED), iloc.bh will remain set to NULL. Since ext4_xattr_inode_dec_ref_all() lacks error checking, this will lead to a null pointer dereference in ext4_raw_inode(), called right after ext4_get_inode_loc(). Found by Linux Verification Center (linuxtesting.org) with SVACE.

• CVE-2025-71064 — CVE-2025-71064 · CWE-909

  In the Linux kernel, the following vulnerability has been resolved: net: hns3: using the num_tqps in the vf driver to apply for resources Currently, hdev->htqp is allocated using hdev->num_tqps, and kinfo->tqp is allocated using kinfo->num_tqps. However, kinfo->num_tqps is set to min(new_tqps, hdev->num_tqps); Therefore, kinfo->num_tqps may be smaller than hdev->num_tqps, which causes some hdev->htqp[i] to remain uninitialized in hclgevf_knic_setup(). Thus, this patch allocates hdev->htqp and kinfo->tqp using hdev->num_tqps, ensuring that the lengths of hdev->htqp and kinfo->tqp are consistent and that all elements are properly initialized.

• CVE-2025-71075 — CVE-2025-71075 · CWE-364

  In the Linux kernel, the following vulnerability has been resolved: scsi: aic94xx: fix use-after-free in device removal path The asd_pci_remove() function fails to synchronize with pending tasklets before freeing the asd_ha structure, leading to a potential use-after-free vulnerability. When a device removal is triggered (via hot-unplug or module unload), race condition can occur. The fix adds tasklet_kill() before freeing the asd_ha structure, ensuring all scheduled tasklets complete before cleanup proceeds.

• CVE-2025-71079 — CVE-2025-71079 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: nfc: fix deadlock between nfc_unregister_device and rfkill_fop_write A deadlock can occur between nfc_unregister_device() and rfkill_fop_write() due to lock ordering inversion between device_lock and rfkill_global_mutex. The problematic lock order is: Thread A (rfkill_fop_write): rfkill_fop_write() mutex_lock(&rfkill_global_mutex) rfkill_set_block() nfc_rfkill_set_block() nfc_dev_down() device_lock(&dev->dev) <- waits for device_lock Thread B (nfc_unregister_device): nfc_unregister_device() device_lock(&dev->dev) rfkill_unregister() mutex_lock(&rfkill_global_mutex) <- waits for rfkill_global_mutex This creates a classic ABBA deadlock scenario. Fix this by moving rfkill_unregister() and rfkill_destroy() outside the device_lock critical section. Store the rfkill pointer in a local variable before releasing the lock, then call rfkill_unregister() after releasing device_lock. This change is safe because rfkill_fop_write() holds rfkill_global_mutex while calling the rfkill callbacks, and rfkill_unregister() also acquires rfkill_global_mutex before cleanup. Therefore, rfkill_unregister() will wait for any ongoing callback to complete before proceeding, and device_del() is only called after rfkill_unregister() returns, preventing any use-after-free. The similar lock ordering in nfc_register_device() (device_lock -> rfkill_global_mutex via rfkill_register) is safe because during registration the device is not yet in rfkill_list, so no concurrent rfkill operations can occur on this device.

• CVE-2025-71085 — CVE-2025-71085 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: ipv6: BUG() in pskb_expand_head() as part of calipso_skbuff_setattr() There exists a kernel oops caused by a BUG_ON(nhead < 0) at net/core/skbuff.c:2232 in pskb_expand_head(). This bug is triggered as part of the calipso_skbuff_setattr() routine when skb_cow() is passed headroom > INT_MAX (i.e. (int)(skb_headroom(skb) + len_delta) < 0). The root cause of the bug is due to an implicit integer cast in __skb_cow(). The check (headroom > skb_headroom(skb)) is meant to ensure that delta = headroom - skb_headroom(skb) is never negative, otherwise we will trigger a BUG_ON in pskb_expand_head(). However, if headroom > INT_MAX and delta <= -NET_SKB_PAD, the check passes, delta becomes negative, and pskb_expand_head() is passed a negative value for nhead. Fix the trigger condition in calipso_skbuff_setattr(). Avoid passing "negative" headroom sizes to skb_cow() within calipso_skbuff_setattr() by only using skb_cow() to grow headroom. PoC: Using `netlabelctl` tool: netlabelctl map del default netlabelctl calipso add pass doi:7 netlabelctl map add default address:0::1/128 protocol:calipso,7 Then run the following PoC: int fd = socket(AF_INET6, SOCK_DGRAM, IPPROTO_UDP); // setup msghdr int cmsg_size = 2; int cmsg_len = 0x60; struct msghdr msg; struct sockaddr_in6 dest_addr; struct cmsghdr * cmsg = (struct cmsghdr *) calloc(1, sizeof(struct cmsghdr) + cmsg_len); msg.msg_name = &dest_addr; msg.msg_namelen = sizeof(dest_addr); msg.msg_iov = NULL; msg.msg_iovlen = 0; msg.msg_control = cmsg; msg.msg_controllen = cmsg_len; msg.msg_flags = 0; // setup sockaddr dest_addr.sin6_family = AF_INET6; dest_addr.sin6_port = htons(31337); dest_addr.sin6_flowinfo = htonl(31337); dest_addr.sin6_addr = in6addr_loopback; dest_addr.sin6_scope_id = 31337; // setup cmsghdr cmsg->cmsg_len = cmsg_len; cmsg->cmsg_level = IPPROTO_IPV6; cmsg->cmsg_type = IPV6_HOPOPTS; char * hop_hdr = (char *)cmsg + sizeof(struct cmsghdr); hop_hdr[1] = 0x9; //set hop size - (0x9 + 1) * 8 = 80 sendmsg(fd, &msg, 0);

• CVE-2025-71086 — CVE-2025-71086 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: rose: fix invalid array index in rose_kill_by_device() rose_kill_by_device() collects sockets into a local array[] and then iterates over them to disconnect sockets bound to a device being brought down. The loop mistakenly indexes array[cnt] instead of array[i]. For cnt < ARRAY_SIZE(array), this reads an uninitialized entry; for cnt == ARRAY_SIZE(array), it is an out-of-bounds read. Either case can lead to an invalid socket pointer dereference and also leaks references taken via sock_hold(). Fix the index to use i.

• CVE-2025-71088 — CVE-2025-71088 · CWE-366

  In the Linux kernel, the following vulnerability has been resolved: mptcp: fallback earlier on simult connection Syzkaller reports a simult-connect race leading to inconsistent fallback status: WARNING: CPU: 3 PID: 33 at net/mptcp/subflow.c:1515 subflow_data_ready+0x40b/0x7c0 net/mptcp/subflow.c:1515 Modules linked in: CPU: 3 UID: 0 PID: 33 Comm: ksoftirqd/3 Not tainted syzkaller #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:subflow_data_ready+0x40b/0x7c0 net/mptcp/subflow.c:1515 Code: 89 ee e8 78 61 3c f6 40 84 ed 75 21 e8 8e 66 3c f6 44 89 fe bf 07 00 00 00 e8 c1 61 3c f6 41 83 ff 07 74 09 e8 76 66 3c f6 90 <0f> 0b 90 e8 6d 66 3c f6 48 89 df e8 e5 ad ff ff 31 ff 89 c5 89 c6 RSP: 0018:ffffc900006cf338 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff888031acd100 RCX: ffffffff8b7f2abf RDX: ffff88801e6ea440 RSI: ffffffff8b7f2aca RDI: 0000000000000005 RBP: 0000000000000000 R08: 0000000000000005 R09: 0000000000000007 R10: 0000000000000004 R11: 0000000000002c10 R12: ffff88802ba69900 R13: 1ffff920000d9e67 R14: ffff888046f81800 R15: 0000000000000004 FS: 0000000000000000(0000) GS:ffff8880d69bc000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000560fc0ca1670 CR3: 0000000032c3a000 CR4: 0000000000352ef0 Call Trace: <TASK> tcp_data_queue+0x13b0/0x4f90 net/ipv4/tcp_input.c:5197 tcp_rcv_state_process+0xfdf/0x4ec0 net/ipv4/tcp_input.c:6922 tcp_v6_do_rcv+0x492/0x1740 net/ipv6/tcp_ipv6.c:1672 tcp_v6_rcv+0x2976/0x41e0 net/ipv6/tcp_ipv6.c:1918 ip6_protocol_deliver_rcu+0x188/0x1520 net/ipv6/ip6_input.c:438 ip6_input_finish+0x1e4/0x4b0 net/ipv6/ip6_input.c:489 NF_HOOK include/linux/netfilter.h:318 [inline] NF_HOOK include/linux/netfilter.h:312 [inline] ip6_input+0x105/0x2f0 net/ipv6/ip6_input.c:500 dst_input include/net/dst.h:471 [inline] ip6_rcv_finish net/ipv6/ip6_input.c:79 [inline] NF_HOOK include/linux/netfilter.h:318 [inline] NF_HOOK include/linux/netfilter.h:312 [inline] ipv6_rcv+0x264/0x650 net/ipv6/ip6_input.c:311 __netif_receive_skb_one_core+0x12d/0x1e0 net/core/dev.c:5979 __netif_receive_skb+0x1d/0x160 net/core/dev.c:6092 process_backlog+0x442/0x15e0 net/core/dev.c:6444 __napi_poll.constprop.0+0xba/0x550 net/core/dev.c:7494 napi_poll net/core/dev.c:7557 [inline] net_rx_action+0xa9f/0xfe0 net/core/dev.c:7684 handle_softirqs+0x216/0x8e0 kernel/softirq.c:579 run_ksoftirqd kernel/softirq.c:968 [inline] run_ksoftirqd+0x3a/0x60 kernel/softirq.c:960 smpboot_thread_fn+0x3f7/0xae0 kernel/smpboot.c:160 kthread+0x3c2/0x780 kernel/kthread.c:463 ret_from_fork+0x5d7/0x6f0 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> The TCP subflow can process the simult-connect syn-ack packet after transitioning to TCP_FIN1 state, bypassing the MPTCP fallback check, as the sk_state_change() callback is not invoked for * -> FIN_WAIT1 transitions. That will move the msk socket to an inconsistent status and the next incoming data will hit the reported splat. Close the race moving the simult-fallback check at the earliest possible stage - that is at syn-ack generation time. About the fixes tags: [2] was supposed to also fix this issue introduced by [3]. [1] is required as a dependence: it was not explicitly marked as a fix, but it is one and it has already been backported before [3]. In other words, this commit should be backported up to [3], including [2] and [1] if that's not already there.

• CVE-2025-71095 — CVE-2025-71095 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: stmmac: fix the crash issue for zero copy XDP_TX action There is a crash issue when running zero copy XDP_TX action, the crash log is shown below. [ 216.122464] Unable to handle kernel paging request at virtual address fffeffff80000000 [ 216.187524] Internal error: Oops: 0000000096000144 [#1] SMP [ 216.301694] Call trace: [ 216.304130] dcache_clean_poc+0x20/0x38 (P) [ 216.308308] __dma_sync_single_for_device+0x1bc/0x1e0 [ 216.313351] stmmac_xdp_xmit_xdpf+0x354/0x400 [ 216.317701] __stmmac_xdp_run_prog+0x164/0x368 [ 216.322139] stmmac_napi_poll_rxtx+0xba8/0xf00 [ 216.326576] __napi_poll+0x40/0x218 [ 216.408054] Kernel panic - not syncing: Oops: Fatal exception in interrupt For XDP_TX action, the xdp_buff is converted to xdp_frame by xdp_convert_buff_to_frame(). The memory type of the resulting xdp_frame depends on the memory type of the xdp_buff. For page pool based xdp_buff it produces xdp_frame with memory type MEM_TYPE_PAGE_POOL. For zero copy XSK pool based xdp_buff it produces xdp_frame with memory type MEM_TYPE_PAGE_ORDER0. However, stmmac_xdp_xmit_back() does not check the memory type and always uses the page pool type, this leads to invalid mappings and causes the crash. Therefore, check the xdp_buff memory type in stmmac_xdp_xmit_back() to fix this issue.

• CVE-2025-71097 — CVE-2025-71097 · CWE-772

  In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix reference count leak when using error routes with nexthop objects When a nexthop object is deleted, it is marked as dead and then fib_table_flush() is called to flush all the routes that are using the dead nexthop. The current logic in fib_table_flush() is to only flush error routes (e.g., blackhole) when it is called as part of network namespace dismantle (i.e., with flush_all=true). Therefore, error routes are not flushed when their nexthop object is deleted: # ip link add name dummy1 up type dummy # ip nexthop add id 1 dev dummy1 # ip route add 198.51.100.1/32 nhid 1 # ip route add blackhole 198.51.100.2/32 nhid 1 # ip nexthop del id 1 # ip route show blackhole 198.51.100.2 nhid 1 dev dummy1 As such, they keep holding a reference on the nexthop object which in turn holds a reference on the nexthop device, resulting in a reference count leak: # ip link del dev dummy1 [ 70.516258] unregister_netdevice: waiting for dummy1 to become free. Usage count = 2 Fix by flushing error routes when their nexthop is marked as dead. IPv6 does not suffer from this problem.

• CVE-2025-71098 — CVE-2025-71098 · CWE-125

  In the Linux kernel, the following vulnerability has been resolved: ip6_gre: make ip6gre_header() robust Over the years, syzbot found many ways to crash the kernel in ip6gre_header() [1]. This involves team or bonding drivers ability to dynamically change their dev->needed_headroom and/or dev->hard_header_len In this particular crash mld_newpack() allocated an skb with a too small reserve/headroom, and by the time mld_sendpack() was called, syzbot managed to attach an ip6gre device. [1] skbuff: skb_under_panic: text:ffffffff8a1d69a8 len:136 put:40 head:ffff888059bc7000 data:ffff888059bc6fe8 tail:0x70 end:0x6c0 dev:team0 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:213 ! <TASK> skb_under_panic net/core/skbuff.c:223 [inline] skb_push+0xc3/0xe0 net/core/skbuff.c:2641 ip6gre_header+0xc8/0x790 net/ipv6/ip6_gre.c:1371 dev_hard_header include/linux/netdevice.h:3436 [inline] neigh_connected_output+0x286/0x460 net/core/neighbour.c:1618 neigh_output include/net/neighbour.h:556 [inline] ip6_finish_output2+0xfb3/0x1480 net/ipv6/ip6_output.c:136 __ip6_finish_output net/ipv6/ip6_output.c:-1 [inline] ip6_finish_output+0x234/0x7d0 net/ipv6/ip6_output.c:220 NF_HOOK_COND include/linux/netfilter.h:307 [inline] ip6_output+0x340/0x550 net/ipv6/ip6_output.c:247 NF_HOOK+0x9e/0x380 include/linux/netfilter.h:318 mld_sendpack+0x8d4/0xe60 net/ipv6/mcast.c:1855 mld_send_cr net/ipv6/mcast.c:2154 [inline] mld_ifc_work+0x83e/0xd60 net/ipv6/mcast.c:2693

• CVE-2025-71104 — CVE-2025-71104 · CWE-681

  In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Fix VM hard lockup after prolonged inactivity with periodic HV timer When advancing the target expiration for the guest's APIC timer in periodic mode, set the expiration to "now" if the target expiration is in the past (similar to what is done in update_target_expiration()). Blindly adding the period to the previous target expiration can result in KVM generating a practically unbounded number of hrtimer IRQs due to programming an expired timer over and over. In extreme scenarios, e.g. if userspace pauses/suspends a VM for an extended duration, this can even cause hard lockups in the host. Currently, the bug only affects Intel CPUs when using the hypervisor timer (HV timer), a.k.a. the VMX preemption timer. Unlike the software timer, a.k.a. hrtimer, which KVM keeps running even on exits to userspace, the HV timer only runs while the guest is active. As a result, if the vCPU does not run for an extended duration, there will be a huge gap between the target expiration and the current time the vCPU resumes running. Because the target expiration is incremented by only one period on each timer expiration, this leads to a series of timer expirations occurring rapidly after the vCPU/VM resumes. More critically, when the vCPU first triggers a periodic HV timer expiration after resuming, advancing the expiration by only one period will result in a target expiration in the past. As a result, the delta may be calculated as a negative value. When the delta is converted into an absolute value (tscdeadline is an unsigned u64), the resulting value can overflow what the HV timer is capable of programming. I.e. the large value will exceed the VMX Preemption Timer's maximum bit width of cpu_preemption_timer_multi + 32, and thus cause KVM to switch from the HV timer to the software timer (hrtimers). After switching to the software timer, periodic timer expiration callbacks may be executed consecutively within a single clock interrupt handler, because hrtimers honors KVM's request for an expiration in the past and immediately re-invokes KVM's callback after reprogramming. And because the interrupt handler runs with IRQs disabled, restarting KVM's hrtimer over and over until the target expiration is advanced to "now" can result in a hard lockup. E.g. the following hard lockup was triggered in the host when running a Windows VM (only relevant because it used the APIC timer in periodic mode) after resuming the VM from a long suspend (in the host). NMI watchdog: Watchdog detected hard LOCKUP on cpu 45 ... RIP: 0010:advance_periodic_target_expiration+0x4d/0x80 [kvm] ... RSP: 0018:ff4f88f5d98d8ef0 EFLAGS: 00000046 RAX: fff0103f91be678e RBX: fff0103f91be678e RCX: 00843a7d9e127bcc RDX: 0000000000000002 RSI: 0052ca4003697505 RDI: ff440d5bfbdbd500 RBP: ff440d5956f99200 R08: ff2ff2a42deb6a84 R09: 000000000002a6c0 R10: 0122d794016332b3 R11: 0000000000000000 R12: ff440db1af39cfc0 R13: ff440db1af39cfc0 R14: ffffffffc0d4a560 R15: ff440db1af39d0f8 FS: 00007f04a6ffd700(0000) GS:ff440db1af380000(0000) knlGS:000000e38a3b8000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000d5651feff8 CR3: 000000684e038002 CR4: 0000000000773ee0 PKRU: 55555554 Call Trace: <IRQ> apic_timer_fn+0x31/0x50 [kvm] __hrtimer_run_queues+0x100/0x280 hrtimer_interrupt+0x100/0x210 ? ttwu_do_wakeup+0x19/0x160 smp_apic_timer_interrupt+0x6a/0x130 apic_timer_interrupt+0xf/0x20 </IRQ> Moreover, if the suspend duration of the virtual machine is not long enough to trigger a hard lockup in this scenario, since commit 98c25ead5eda ("KVM: VMX: Move preemption timer <=> hrtimer dance to common x86"), KVM will continue using the software timer until the guest reprograms the APIC timer in some way. Since the periodic timer does not require frequent APIC timer register programming, the guest may continue to use the software timer in ---truncated---

• CVE-2025-71112 — CVE-2025-71112 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: net: hns3: add VLAN id validation before using Currently, the VLAN id may be used without validation when receive a VLAN configuration mailbox from VF. The length of vlan_del_fail_bmap is BITS_TO_LONGS(VLAN_N_VID). It may cause out-of-bounds memory access once the VLAN id is bigger than or equal to VLAN_N_VID. Therefore, VLAN id needs to be checked to ensure it is within the range of VLAN_N_VID.

• CVE-2025-71113 — CVE-2025-71113 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - zero initialize memory allocated via sock_kmalloc Several crypto user API contexts and requests allocated with sock_kmalloc() were left uninitialized, relying on callers to set fields explicitly. This resulted in the use of uninitialized data in certain error paths or when new fields are added in the future. The ACVP patches also contain two user-space interface files: algif_kpp.c and algif_akcipher.c. These too rely on proper initialization of their context structures. A particular issue has been observed with the newly added 'inflight' variable introduced in af_alg_ctx by commit: 67b164a871af ("crypto: af_alg - Disallow multiple in-flight AIO requests") Because the context is not memset to zero after allocation, the inflight variable has contained garbage values. As a result, af_alg_alloc_areq() has incorrectly returned -EBUSY randomly when the garbage value was interpreted as true: https://github.com/gregkh/linux/blame/master/crypto/af_alg.c#L1209 The check directly tests ctx->inflight without explicitly comparing against true/false. Since inflight is only ever set to true or false later, an uninitialized value has triggered -EBUSY failures. Zero-initializing memory allocated with sock_kmalloc() ensures inflight and other fields start in a known state, removing random issues caused by uninitialized data.

• CVE-2025-71114 — CVE-2025-71114 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: via_wdt: fix critical boot hang due to unnamed resource allocation The VIA watchdog driver uses allocate_resource() to reserve a MMIO region for the watchdog control register. However, the allocated resource was not given a name, which causes the kernel resource tree to contain an entry marked as "<BAD>" under /proc/iomem on x86 platforms. During boot, this unnamed resource can lead to a critical hang because subsequent resource lookups and conflict checks fail to handle the invalid entry properly.

• CVE-2025-71120 — CVE-2025-71120 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: SUNRPC: svcauth_gss: avoid NULL deref on zero length gss_token in gss_read_proxy_verf A zero length gss_token results in pages == 0 and in_token->pages[0] is NULL. The code unconditionally evaluates page_address(in_token->pages[0]) for the initial memcpy, which can dereference NULL even when the copy length is 0. Guard the first memcpy so it only runs when length > 0.

• CVE-2025-71123 — CVE-2025-71123 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: ext4: fix string copying in parse_apply_sb_mount_options() strscpy_pad() can't be used to copy a non-NUL-term string into a NUL-term string of possibly bigger size. Commit 0efc5990bca5 ("string.h: Introduce memtostr() and memtostr_pad()") provides additional information in that regard. So if this happens, the following warning is observed: strnlen: detected buffer overflow: 65 byte read of buffer size 64 WARNING: CPU: 0 PID: 28655 at lib/string_helpers.c:1032 __fortify_report+0x96/0xc0 lib/string_helpers.c:1032 Modules linked in: CPU: 0 UID: 0 PID: 28655 Comm: syz-executor.3 Not tainted 6.12.54-syzkaller-00144-g5f0270f1ba00 #0 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:__fortify_report+0x96/0xc0 lib/string_helpers.c:1032 Call Trace: <TASK> __fortify_panic+0x1f/0x30 lib/string_helpers.c:1039 strnlen include/linux/fortify-string.h:235 [inline] sized_strscpy include/linux/fortify-string.h:309 [inline] parse_apply_sb_mount_options fs/ext4/super.c:2504 [inline] __ext4_fill_super fs/ext4/super.c:5261 [inline] ext4_fill_super+0x3c35/0xad00 fs/ext4/super.c:5706 get_tree_bdev_flags+0x387/0x620 fs/super.c:1636 vfs_get_tree+0x93/0x380 fs/super.c:1814 do_new_mount fs/namespace.c:3553 [inline] path_mount+0x6ae/0x1f70 fs/namespace.c:3880 do_mount fs/namespace.c:3893 [inline] __do_sys_mount fs/namespace.c:4103 [inline] __se_sys_mount fs/namespace.c:4080 [inline] __x64_sys_mount+0x280/0x300 fs/namespace.c:4080 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x64/0x140 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x76/0x7e Since userspace is expected to provide s_mount_opts field to be at most 63 characters long with the ending byte being NUL-term, use a 64-byte buffer which matches the size of s_mount_opts, so that strscpy_pad() does its job properly. Return with error if the user still managed to provide a non-NUL-term string here. Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

• CVE-2025-71131 — CVE-2025-71131 · CWE-825

  In the Linux kernel, the following vulnerability has been resolved: crypto: seqiv - Do not use req->iv after crypto_aead_encrypt As soon as crypto_aead_encrypt is called, the underlying request may be freed by an asynchronous completion. Thus dereferencing req->iv after it returns is invalid. Instead of checking req->iv against info, create a new variable unaligned_info and use it for that purpose instead.

• CVE-2025-71161 — CVE-2025-71161 · CWE-835

  In the Linux kernel, the following vulnerability has been resolved: dm-verity: disable recursive forward error correction There are two problems with the recursive correction: 1. It may cause denial-of-service. In fec_read_bufs, there is a loop that has 253 iterations. For each iteration, we may call verity_hash_for_block recursively. There is a limit of 4 nested recursions - that means that there may be at most 253^4 (4 billion) iterations. Red Hat QE team actually created an image that pushes dm-verity to this limit - and this image just makes the udev-worker process get stuck in the 'D' state. 2. It doesn't work. In fec_read_bufs we store data into the variable "fio->bufs", but fio bufs is shared between recursive invocations, if "verity_hash_for_block" invoked correction recursively, it would overwrite partially filled fio->bufs.

• CVE-2025-71162 — CVE-2025-71162 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: tegra-adma: Fix use-after-free A use-after-free bug exists in the Tegra ADMA driver when audio streams are terminated, particularly during XRUN conditions. The issue occurs when the DMA buffer is freed by tegra_adma_terminate_all() before the vchan completion tasklet finishes accessing it. The race condition follows this sequence: 1. DMA transfer completes, triggering an interrupt that schedules the completion tasklet (tasklet has not executed yet) 2. Audio playback stops, calling tegra_adma_terminate_all() which frees the DMA buffer memory via kfree() 3. The scheduled tasklet finally executes, calling vchan_complete() which attempts to access the already-freed memory Since tasklets can execute at any time after being scheduled, there is no guarantee that the buffer will remain valid when vchan_complete() runs. Fix this by properly synchronizing the virtual channel completion: - Calling vchan_terminate_vdesc() in tegra_adma_stop() to mark the descriptors as terminated instead of freeing the descriptor. - Add the callback tegra_adma_synchronize() that calls vchan_synchronize() which kills any pending tasklets and frees any terminated descriptors. Crash logs: [ 337.427523] BUG: KASAN: use-after-free in vchan_complete+0x124/0x3b0 [ 337.427544] Read of size 8 at addr ffff000132055428 by task swapper/0/0 [ 337.427562] Call trace: [ 337.427564] dump_backtrace+0x0/0x320 [ 337.427571] show_stack+0x20/0x30 [ 337.427575] dump_stack_lvl+0x68/0x84 [ 337.427584] print_address_description.constprop.0+0x74/0x2b8 [ 337.427590] kasan_report+0x1f4/0x210 [ 337.427598] __asan_load8+0xa0/0xd0 [ 337.427603] vchan_complete+0x124/0x3b0 [ 337.427609] tasklet_action_common.constprop.0+0x190/0x1d0 [ 337.427617] tasklet_action+0x30/0x40 [ 337.427623] __do_softirq+0x1a0/0x5c4 [ 337.427628] irq_exit+0x110/0x140 [ 337.427633] handle_domain_irq+0xa4/0xe0 [ 337.427640] gic_handle_irq+0x64/0x160 [ 337.427644] call_on_irq_stack+0x20/0x4c [ 337.427649] do_interrupt_handler+0x7c/0x90 [ 337.427654] el1_interrupt+0x30/0x80 [ 337.427659] el1h_64_irq_handler+0x18/0x30 [ 337.427663] el1h_64_irq+0x7c/0x80 [ 337.427667] cpuidle_enter_state+0xe4/0x540 [ 337.427674] cpuidle_enter+0x54/0x80 [ 337.427679] do_idle+0x2e0/0x380 [ 337.427685] cpu_startup_entry+0x2c/0x70 [ 337.427690] rest_init+0x114/0x130 [ 337.427695] arch_call_rest_init+0x18/0x24 [ 337.427702] start_kernel+0x380/0x3b4 [ 337.427706] __primary_switched+0xc0/0xc8

• CVE-2025-71163 — CVE-2025-71163 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: fix device leaks on compat bind and unbind Make sure to drop the reference taken when looking up the idxd device as part of the compat bind and unbind sysfs interface.

• CVE-2025-71185 — CVE-2025-71185 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: ti: dma-crossbar: fix device leak on am335x route allocation Make sure to drop the reference taken when looking up the crossbar platform device during am335x route allocation.

• CVE-2025-71186 — CVE-2025-71186 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: stm32: dmamux: fix device leak on route allocation Make sure to drop the reference taken when looking up the DMA mux platform device during route allocation. Note that holding a reference to a device does not prevent its driver data from going away so there is no point in keeping the reference.

• CVE-2025-71189 — CVE-2025-71189 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: dw: dmamux: fix OF node leak on route allocation failure Make sure to drop the reference taken to the DMA master OF node also on late route allocation failures.

• CVE-2025-71190 — CVE-2025-71190 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: bcm-sba-raid: fix device leak on probe Make sure to drop the reference taken when looking up the mailbox device during probe on probe failures and on driver unbind.

• CVE-2025-71191 — CVE-2025-71191 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: at_hdmac: fix device leak on of_dma_xlate() Make sure to drop the reference taken when looking up the DMA platform device during of_dma_xlate() when releasing channel resources. Note that commit 3832b78b3ec2 ("dmaengine: at_hdmac: add missing put_device() call in at_dma_xlate()") fixed the leak in a couple of error paths but the reference is still leaking on successful allocation.

• CVE-2025-71197 — CVE-2025-71197 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: w1: therm: Fix off-by-one buffer overflow in alarms_store The sysfs buffer passed to alarms_store() is allocated with 'size + 1' bytes and a NUL terminator is appended. However, the 'size' argument does not account for this extra byte. The original code then allocated 'size' bytes and used strcpy() to copy 'buf', which always writes one byte past the allocated buffer since strcpy() copies until the NUL terminator at index 'size'. Fix this by parsing the 'buf' parameter directly using simple_strtoll() without allocating any intermediate memory or string copying. This removes the overflow while simplifying the code.

• CVE-2025-71221 — CVE-2025-71221 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: dmaengine: mmp_pdma: Fix race condition in mmp_pdma_residue() Add proper locking in mmp_pdma_residue() to prevent use-after-free when accessing descriptor list and descriptor contents. The race occurs when multiple threads call tx_status() while the tasklet on another CPU is freeing completed descriptors: CPU 0 CPU 1 ----- ----- mmp_pdma_tx_status() mmp_pdma_residue() -> NO LOCK held list_for_each_entry(sw, ..) DMA interrupt dma_do_tasklet() -> spin_lock(&desc_lock) list_move(sw->node, ...) spin_unlock(&desc_lock) | dma_pool_free(sw) <- FREED! -> access sw->desc <- UAF! This issue can be reproduced when running dmatest on the same channel with multiple threads (threads_per_chan > 1). Fix by protecting the chain_running list iteration and descriptor access with the chan->desc_lock spinlock.

• CVE-2025-71265 — CVE-2025-71265 · CWE-20

  In the Linux kernel, the following vulnerability has been resolved: fs: ntfs3: fix infinite loop in attr_load_runs_range on inconsistent metadata We found an infinite loop bug in the ntfs3 file system that can lead to a Denial-of-Service (DoS) condition. A malformed NTFS image can cause an infinite loop when an attribute header indicates an empty run list, while directory entries reference it as containing actual data. In NTFS, setting evcn=-1 with svcn=0 is a valid way to represent an empty run list, and run_unpack() correctly handles this by checking if evcn + 1 equals svcn and returning early without parsing any run data. However, this creates a problem when there is metadata inconsistency, where the attribute header claims to be empty (evcn=-1) but the caller expects to read actual data. When run_unpack() immediately returns success upon seeing this condition, it leaves the runs_tree uninitialized with run->runs as a NULL. The calling function attr_load_runs_range() assumes that a successful return means that the runs were loaded and sets clen to 0, expecting the next run_lookup_entry() call to succeed. Because runs_tree remains uninitialized, run_lookup_entry() continues to fail, and the loop increments vcn by zero (vcn += 0), leading to an infinite loop. This patch adds a retry counter to detect when run_lookup_entry() fails consecutively after attr_load_runs_vcn(). If the run is still not found on the second attempt, it indicates corrupted metadata and returns -EINVAL, preventing the Denial-of-Service (DoS) vulnerability.

• CVE-2025-71266 — CVE-2025-71266 · CWE-835

  In the Linux kernel, the following vulnerability has been resolved: fs: ntfs3: check return value of indx_find to avoid infinite loop We found an infinite loop bug in the ntfs3 file system that can lead to a Denial-of-Service (DoS) condition. A malformed dentry in the ntfs3 filesystem can cause the kernel to hang during the lookup operations. By setting the HAS_SUB_NODE flag in an INDEX_ENTRY within a directory's INDEX_ALLOCATION block and manipulating the VCN pointer, an attacker can cause the indx_find() function to repeatedly read the same block, allocating 4 KB of memory each time. The kernel lacks VCN loop detection and depth limits, causing memory exhaustion and an OOM crash. This patch adds a return value check for fnd_push() to prevent a memory exhaustion vulnerability caused by infinite loops. When the index exceeds the size of the fnd->nodes array, fnd_push() returns -EINVAL. The indx_find() function checks this return value and stops processing, preventing further memory allocation.

• CVE-2025-71267 — CVE-2025-71267 · CWE-835

  In the Linux kernel, the following vulnerability has been resolved: fs: ntfs3: fix infinite loop triggered by zero-sized ATTR_LIST We found an infinite loop bug in the ntfs3 file system that can lead to a Denial-of-Service (DoS) condition. A malformed NTFS image can cause an infinite loop when an ATTR_LIST attribute indicates a zero data size while the driver allocates memory for it. When ntfs_load_attr_list() processes a resident ATTR_LIST with data_size set to zero, it still allocates memory because of al_aligned(0). This creates an inconsistent state where ni->attr_list.size is zero, but ni->attr_list.le is non-null. This causes ni_enum_attr_ex to incorrectly assume that no attribute list exists and enumerates only the primary MFT record. When it finds ATTR_LIST, the code reloads it and restarts the enumeration, repeating indefinitely. The mount operation never completes, hanging the kernel thread. This patch adds validation to ensure that data_size is non-zero before memory allocation. When a zero-sized ATTR_LIST is detected, the function returns -EINVAL, preventing a DoS vulnerability.

• CVE-2026-3497 — CVE-2026-3497 · CWE-908

  Vulnerability in the OpenSSH GSSAPI delta included in various Linux distributions. This vulnerability affects the GSSAPI patches added by various Linux distributions and does not affect the OpenSSH upstream project itself. The usage of sshpkt_disconnect() on an error, which does not terminate the process, allows an attacker to send an unexpected GSSAPI message type during the GSSAPI key exchange to the server, which will call the underlying function and continue the execution of the program without setting the related connection variables. As the variables are not initialized to NULL the code later accesses those uninitialized variables, accessing random memory, which could lead to undefined behavior. The recommended workaround is to use ssh_packet_disconnect() instead, which does terminate the process. The impact of the vulnerability depends heavily on the compiler flag hardening configuration.

• CVE-2026-22977 — CVE-2026-22977 · CWE-489

  In the Linux kernel, the following vulnerability has been resolved: net: sock: fix hardened usercopy panic in sock_recv_errqueue skbuff_fclone_cache was created without defining a usercopy region, [1] unlike skbuff_head_cache which properly whitelists the cb[] field. [2] This causes a usercopy BUG() when CONFIG_HARDENED_USERCOPY is enabled and the kernel attempts to copy sk_buff.cb data to userspace via sock_recv_errqueue() -> put_cmsg(). The crash occurs when: 1. TCP allocates an skb using alloc_skb_fclone() (from skbuff_fclone_cache) [1] 2. The skb is cloned via skb_clone() using the pre-allocated fclone [3] 3. The cloned skb is queued to sk_error_queue for timestamp reporting 4. Userspace reads the error queue via recvmsg(MSG_ERRQUEUE) 5. sock_recv_errqueue() calls put_cmsg() to copy serr->ee from skb->cb [4] 6. __check_heap_object() fails because skbuff_fclone_cache has no usercopy whitelist [5] When cloned skbs allocated from skbuff_fclone_cache are used in the socket error queue, accessing the sock_exterr_skb structure in skb->cb via put_cmsg() triggers a usercopy hardening violation: [ 5.379589] usercopy: Kernel memory exposure attempt detected from SLUB object 'skbuff_fclone_cache' (offset 296, size 16)! [ 5.382796] kernel BUG at mm/usercopy.c:102! [ 5.383923] Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI [ 5.384903] CPU: 1 UID: 0 PID: 138 Comm: poc_put_cmsg Not tainted 6.12.57 #7 [ 5.384903] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 [ 5.384903] RIP: 0010:usercopy_abort+0x6c/0x80 [ 5.384903] Code: 1a 86 51 48 c7 c2 40 15 1a 86 41 52 48 c7 c7 c0 15 1a 86 48 0f 45 d6 48 c7 c6 80 15 1a 86 48 89 c1 49 0f 45 f3 e8 84 27 88 ff <0f> 0b 490 [ 5.384903] RSP: 0018:ffffc900006f77a8 EFLAGS: 00010246 [ 5.384903] RAX: 000000000000006f RBX: ffff88800f0ad2a8 RCX: 1ffffffff0f72e74 [ 5.384903] RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff87b973a0 [ 5.384903] RBP: 0000000000000010 R08: 0000000000000000 R09: fffffbfff0f72e74 [ 5.384903] R10: 0000000000000003 R11: 79706f6372657375 R12: 0000000000000001 [ 5.384903] R13: ffff88800f0ad2b8 R14: ffffea00003c2b40 R15: ffffea00003c2b00 [ 5.384903] FS: 0000000011bc4380(0000) GS:ffff8880bf100000(0000) knlGS:0000000000000000 [ 5.384903] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5.384903] CR2: 000056aa3b8e5fe4 CR3: 000000000ea26004 CR4: 0000000000770ef0 [ 5.384903] PKRU: 55555554 [ 5.384903] Call Trace: [ 5.384903] <TASK> [ 5.384903] __check_heap_object+0x9a/0xd0 [ 5.384903] __check_object_size+0x46c/0x690 [ 5.384903] put_cmsg+0x129/0x5e0 [ 5.384903] sock_recv_errqueue+0x22f/0x380 [ 5.384903] tls_sw_recvmsg+0x7ed/0x1960 [ 5.384903] ? srso_alias_return_thunk+0x5/0xfbef5 [ 5.384903] ? schedule+0x6d/0x270 [ 5.384903] ? srso_alias_return_thunk+0x5/0xfbef5 [ 5.384903] ? mutex_unlock+0x81/0xd0 [ 5.384903] ? __pfx_mutex_unlock+0x10/0x10 [ 5.384903] ? __pfx_tls_sw_recvmsg+0x10/0x10 [ 5.384903] ? _raw_spin_lock_irqsave+0x8f/0xf0 [ 5.384903] ? _raw_read_unlock_irqrestore+0x20/0x40 [ 5.384903] ? srso_alias_return_thunk+0x5/0xfbef5 The crash offset 296 corresponds to skb2->cb within skbuff_fclones: - sizeof(struct sk_buff) = 232 - offsetof(struct sk_buff, cb) = 40 - offset of skb2.cb in fclones = 232 + 40 = 272 - crash offset 296 = 272 + 24 (inside sock_exterr_skb.ee) This patch uses a local stack variable as a bounce buffer to avoid the hardened usercopy check failure. [1] https://elixir.bootlin.com/linux/v6.12.62/source/net/ipv4/tcp.c#L885 [2] https://elixir.bootlin.com/linux/v6.12.62/source/net/core/skbuff.c#L5104 [3] https://elixir.bootlin.com/linux/v6.12.62/source/net/core/skbuff.c#L5566 [4] https://elixir.bootlin.com/linux/v6.12.62/source/net/core/skbuff.c#L5491 [5] https://elixir.bootlin.com/linux/v6.12.62/source/mm/slub.c#L5719

• CVE-2026-22979 — CVE-2026-22979 · CWE-772

  In the Linux kernel, the following vulnerability has been resolved: net: fix memory leak in skb_segment_list for GRO packets When skb_segment_list() is called during packet forwarding, it handles packets that were aggregated by the GRO engine. Historically, the segmentation logic in skb_segment_list assumes that individual segments are split from a parent SKB and may need to carry their own socket memory accounting. Accordingly, the code transfers truesize from the parent to the newly created segments. Prior to commit ed4cccef64c1 ("gro: fix ownership transfer"), this truesize subtraction in skb_segment_list() was valid because fragments still carry a reference to the original socket. However, commit ed4cccef64c1 ("gro: fix ownership transfer") changed this behavior by ensuring that fraglist entries are explicitly orphaned (skb->sk = NULL) to prevent illegal orphaning later in the stack. This change meant that the entire socket memory charge remained with the head SKB, but the corresponding accounting logic in skb_segment_list() was never updated. As a result, the current code unconditionally adds each fragment's truesize to delta_truesize and subtracts it from the parent SKB. Since the fragments are no longer charged to the socket, this subtraction results in an effective under-count of memory when the head is freed. This causes sk_wmem_alloc to remain non-zero, preventing socket destruction and leading to a persistent memory leak. The leak can be observed via KMEMLEAK when tearing down the networking environment: unreferenced object 0xffff8881e6eb9100 (size 2048): comm "ping", pid 6720, jiffies 4295492526 backtrace: kmem_cache_alloc_noprof+0x5c6/0x800 sk_prot_alloc+0x5b/0x220 sk_alloc+0x35/0xa00 inet6_create.part.0+0x303/0x10d0 __sock_create+0x248/0x640 __sys_socket+0x11b/0x1d0 Since skb_segment_list() is exclusively used for SKB_GSO_FRAGLIST packets constructed by GRO, the truesize adjustment is removed. The call to skb_release_head_state() must be preserved. As documented in commit cf673ed0e057 ("net: fix fraglist segmentation reference count leak"), it is still required to correctly drop references to SKB extensions that may be overwritten during __copy_skb_header().

Acknowledgments, as the advisory lists them

• Siemens ProductCERT: reported these vulnerabilities to CISA.

The advisory's legal notice

The use of Siemens Security Advisories is subject to the terms and conditions listed on: https://www.siemens.com/productcert/terms-of-use.

Sources

• The advisory at cisa.gov
• The CSAF document (JSON)

DeSpy's copy of this version is dated 2026-09-28.